sudo cdrecord-dvd dev=benq -v -sao -eject <image> Cdrecord-Clone 2.01-dvd (x86_64-suse-linux) Copyright (C) 1995-2004 Jörg Schilling Note: This version is an unofficial (modified) version with DVD support Note: and therefore may have bugs that are not present in the original. Note: Please send bug reports or support requests to http://bugs.opensuse.org/ Note: The author of cdrecord should not be bothered with problems in
Moin, ich versuche gerade, meinen Benq DW1650 mit cdrecord-dvd in Betrieb zu nehmen. Das Brennen von DVDs klappt auch weitgehend: -------------- this version. TOC Type: 1 = CD-ROM scsidev: 'ATA:0,0,0' devname: 'ATA' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.5.27 Using libscg version 'schily-0.8'. cdrecord-dvd: Warning: using inofficial libscg transport code version (okir@suse.de-scsi-linux-sg.c-1.83-resmgr-patch '@(#)scsi-linux-sg.c 1.83 04/05/20 Copyright 1997 J. Schilling'). Driveropts: 'burnfree' SCSI buffer size: 64512 atapi: -1 Device type : Removable CD-ROM Version : 0 Response Format: 1 Vendor_info : 'BENQ ' Identifikation : 'DVD DD DW1650 ' Revision : 'BCFC' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: 0x001B Profile: 0x002B Profile: 0x001B (current) Profile: 0x001A Profile: 0x0016 Profile: 0x0015 Profile: 0x0014 Profile: 0x0013 Profile: 0x0011 Profile: 0x0010 Profile: 0x000A Profile: 0x0009 Profile: 0x0008 cdrecord-dvd: Found DVD media: using cdr_mdvd. Using generic SCSI-3/mmc DVD-R(W) driver (mmc_mdvd). Driver flags : SWABAUDIO BURNFREE Supported modes: PACKET SAO Drive buf size : 688128 = 672 KB FIFO size : 134217728 = 131072 KB Track 01: data 1150 MB Total size: 1321 MB (130:56.89) = 589267 sectors Lout start: 1322 MB (130:58/67) = 589267 sectors Current Secsize: 2048 ATIP start of lead out: 157789 (35:05/64) Blocks total: 2295104 Blocks current: 2295104 Blocks remaining: 1705837 scsi_set_streaming Speed set to 11080 KB/s Starting to write CD/DVD at speed 8.0 in real SAO mode for single session. Last chance to quit, starting real write 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. trackno=0 BURN-Free is ON. Turning BURN-Free off BURN-Free is OFF. cdrecord-dvd: Turning BURN-Free on Performing OPC... Sending CUE sheet... cdrecord-dvd: WARNING: Drive returns wrong startsec (0) using -150 Starting new track at sector: 0 Track 01: 1150 of 1150 MB written (fifo 100%) [buf 56%] 2.4x. Track 01: Total bytes read/written: 1206818816/1206818816 (589267 sectors). Writing time: 473.995s Average write speed 1.9x. Min drive buffer fill was 1% Total of 7 possible drive buffer underruns predicted. Fixating... Fixating time: 0.591s cdrecord-dvd: fifo had 19009 puts and 19009 gets. cdrecord-dvd: fifo was 0 times empty and 9370 times full, min fill was 99%. -------------- Nur: Er fixiert die DVDs nicht automatisch (Fixating time 0.591s wäre reichlich schnell). :-( Ein anschließendes "sudo cdrecord-dvd dev=benq -v -fix" produziert dann zwar eine sauber fixierte und lesbare DVD, aber warum brauche ich dafür zwei Schritte? Das war bei meinem alten System (8.0 mit NEC Brenner) nicht nötig, allerdings hatte ich da auch das offizielle cdrecord. Fehlt mir da ein magischer Schalter oder brauche ich die Schilling-Version? Achja: /etc/default/crecord -------------- benq= ATA:0,0,0 48 -1 burnfree CDR_DEVICE=benq CDR_FIFOSIZE=128m -------------- Danke im Voraus Martin