Re: (..) Re: Wlan Speed - Up- und Download zu niedrig

25 May 2011

      Kyek, Andreas, VF-DE schrieb:
...
Ralf Arndt [...]
...
Kann hier jemand etwas zum Modul carl9170 sagen?
@Ernst: Versuche mal ein rmmod carl9170
Das kannst du dir in den Sourcen selber ansehen:
/usr/src/.../drivers/net/wireless/ath/ (in Kconfig)
a) ar9170: "Atheros AR9170 802.11n USB Support" needs firmware 
...Drivers/ar9170
b) carl9170: "Linux Community AR9179 802.11n USB support"
depends on ... EXPERIMENTAL ... provides more features than the 
original, but it need special firmware (carl9170-1.fw) to do 
that
Also das sind beides Treiber für die gleiche Karte; carl ist der 
neuere aber experimentelle Treiber.
Warum zum Henker beide geladen sind? Das macht IMO keinen Sinn.
evtl. einen auf die "Blacklist" setzen?
Andreas
hallo

Spaßvögel sind mir immer willkommen, insbesondere wenn sie auch
was zur Lösung des Problems beitragen können bzw wollen.  Damit
können wir aber das Thema Loopback als erledigt betrachten.

Zur Thema über die Firmware  kann ich folgendes beitragen:
Mit der Distri 11.4 wird das Paket kernel-firmware ausgeliefert.
Darin sind auch ar9170-1 und ar9170-2 enthalten, sind jedoch nicht
für den AVM  Fritz Wlan Stick USB N (300 Mbit/s)  geeignet.

Für den genannten Wlan-Stick gibt es bei opensuse.org auch
das Paket ar9170-firmware mit folgender Beschreibung:
[Zitat]
ar9170-firmware
- Firmware images for Atheros draft-n USB WLAN cards -
This package contains binary firmware images for Atheros draft-N USB
WLAN adaptors in combination with the new mac80211-based driver
ar9170usb.ko. The files will be copied to /lib/firmware.
[/Zitat Ende]

Das Modul "carl9170" ist für MAC - Aktivierung durch Auswahl:
 entweder ar9170usb   oder   carl9170
Siehe auch weiter unten (Auszug aus /var/log/messages)

Ich habe  "rmmod carl9170" ausgeführt, keine Veränderung

dazu hier noch auszugsweise lsmod:

[Zitat - auszugsweise]
biberbau:~ # lsmod
Module                  Size  Used by
[ . . .]
carl9170               77067  0
ar9170usb              52845  0
mac80211              264354  2 carl9170,ar9170usb
ath                    14619  2 carl9170,ar9170usb
cfg80211              154761  4 carl9170,ar9170usb,mac80211,ath
rfkill                 17734  1 cfg80211
[ . . . ]
via_rhine              20927  0
[ . . .]
 carl9170,ar9170usb,usb_storage,ohci_hcd,uhci_hcd,ehci_hcd
biberbau:~ #
[/Zitat Ende]

Weil in /var/log/messages auch viele Infos zur Firmware stehen,
füge ich einen Auszug der Datei bei, damit auch andere Inhalte
überprüft werden können:

[ Zitat /va/log messages]
May 25 17:17:43 biberbau kernel: imklog 5.6.3, log source =
/proc/kmsg started.
May 25 17:17:43 biberbau rsyslogd: [origin software="rsyslogd"
swVersion="5.6.3" x-pid="974" x-info="http://www.rsyslog.com"] start
May 25 17:17:43 biberbau kernel: [   12.098539] ip6_tables: (C)
2000-2006 Netfilter Core Team
May 25 17:17:43 biberbau kernel: [   12.174291] nf_conntrack version
0.5.0 (16384 buckets, 65536 max)
May 25 17:17:43 biberbau kernel: [   12.192527] ip_tables: (C)
2000-2006 Netfilter Core Team
May 25 17:17:46 biberbau kernel: [   16.491464] BIOS EDD facility
v0.16 2004-Jun-25, 1 devices found
May 25 17:17:47 biberbau polkitd[1147]: started daemon version 0.99
using authority implementation `local' version `0.99'
May 25 17:17:49 biberbau ifup:     lo
May 25 17:17:49 biberbau ifup:     lo
May 25 17:17:49 biberbau ifup: IP address: 127.0.0.1/8
May 25 17:17:49 biberbau ifup:
May 25 17:17:49 biberbau ifup:
May 25 17:17:49 biberbau ifup: IP address: 127.0.0.2/8
May 25 17:17:49 biberbau ifup:
May 25 17:17:49 biberbau ifup:     eth0      device: VIA
Technologies, Inc. VT6102 [Rhine-II] (rev 78)
May 25 17:17:49 biberbau ifup:               No configuration found
for eth0
May 25 17:18:03 biberbau kernel: [   33.049758] usb 1-6: USB
disconnect, address 2
May 25 17:18:04 biberbau kernel: [   34.328023] usb 1-6: new high
speed USB device using ehci_hcd and address 3
May 25 17:18:04 biberbau kernel: [   34.491336] usb 1-6: New USB
device found, idVendor=057c, idProduct=8401
May 25 17:18:04 biberbau kernel: [   34.491341] usb 1-6: New USB
device strings: Mfr=16, Product=32, SerialNumber=48
May 25 17:18:04 biberbau kernel: [   34.491345] usb 1-6: Product:
FRITZ!WLAN USB Stick N
May 25 17:18:04 biberbau kernel: [   34.491348] usb 1-6:
Manufacturer: AVM Berlin
May 25 17:18:04 biberbau kernel: [   34.491351] usb 1-6:
SerialNumber: BC054301A052
May 25 17:18:04 biberbau kernel: [   34.584023] cfg80211: Calling
CRDA to update world regulatory domain
May 25 17:18:04 biberbau kernel: [   34.780633] cfg80211: World
regulatory domain updated:
May 25 17:18:04 biberbau kernel: [   34.780638]     (start_freq -
end_freq @ bandwidth), (max_antenna_gain, max_eirp)
May 25 17:18:04 biberbau kernel: [   34.780643]     (2402000 KHz -
2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
May 25 17:18:04 biberbau kernel: [   34.780647]     (2457000 KHz -
2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
May 25 17:18:04 biberbau kernel: [   34.780650]     (2474000 KHz -
2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
May 25 17:18:04 biberbau kernel: [   34.780654]     (5170000 KHz -
5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
May 25 17:18:04 biberbau kernel: [   34.780658]     (5735000 KHz -
5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
May 25 17:18:04 biberbau kernel: [   34.836038] usb 1-6: reset high
speed USB device using ehci_hcd and address 3
May 25 17:18:05 biberbau kernel: [   35.988200] usbcore: registered
new interface driver ar9170usb
May 25 17:18:06 biberbau kernel: [   36.009854] usbcore: registered
new interface driver carl9170
May 25 17:18:06 biberbau kernel: [   36.482090] ath: EEPROM
regdomain: 0x8114
May 25 17:18:06 biberbau kernel: [   36.482095] ath: EEPROM
indicates we should expect a country code
May 25 17:18:06 biberbau kernel: [   36.482098] ath: doing EEPROM
country->regdmn map search
May 25 17:18:06 biberbau kernel: [   36.482101] ath: country maps to
regdmn code: 0x37
May 25 17:18:06 biberbau kernel: [   36.482105] ath: Country alpha2
being used: DE
May 25 17:18:06 biberbau kernel: [   36.482107] ath: Regpair used: 0x37
May 25 17:18:06 biberbau kernel: [   36.539364] ieee80211 phy0:
Selected rate control algorithm 'minstrel_ht'
May 25 17:18:06 biberbau kernel: [   36.541223] cfg80211: Calling
CRDA for country: DE
May 25 17:18:06 biberbau kernel: [   36.542909] Registered led
device: ar9170-phy0::tx
May 25 17:18:06 biberbau kernel: [   36.542968] Registered led
device: ar9170-phy0::assoc
May 25 17:18:06 biberbau kernel: [   36.542976] usb 1-6: Atheros
AR9170 is registered as 'phy0'
May 25 17:18:06 biberbau kernel: [   36.552162] cfg80211: Regulatory
domain changed to country: DE
May 25 17:18:06 biberbau kernel: [   36.552167]     (start_freq -
end_freq @ bandwidth), (max_antenna_gain, max_eirp)
May 25 17:18:06 biberbau kernel: [   36.552171]     (2400000 KHz -
2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
May 25 17:18:06 biberbau kernel: [   36.552174]     (5150000 KHz -
5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
May 25 17:18:06 biberbau kernel: [   36.552178]     (5470000 KHz -
5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
May 25 17:18:06 biberbau ifup:     wlan0     name: FRITZ!WLAN USB
Stick N
May 25 17:18:06 biberbau ifup-wireless:     wlan0     starting
wpa_supplicant
May 25 17:18:08 biberbau kernel: [   38.052449] ADDRCONF(NETDEV_UP):
wlan0: link is not ready
May 25 17:18:08 biberbau kernel: [   38.087020] NET: Registered
protocol family 17
May 25 17:18:08 biberbau ifup-dhcp: Starting DHCP4 client on wlan0
May 25 17:18:08 biberbau dhcpcd[2202]: wlan0: dhcpcd 3.2.3 starting
May 25 17:18:08 biberbau dhcpcd[2202]: wlan0: hardware address =
bc:05:43:01:a0:52
May 25 17:18:08 biberbau dhcpcd[2202]: wlan0: broadcasting for a lease
May 25 17:18:08 biberbau ifup-dhcp: .
May 25 17:18:11 biberbau ifup-dhcp: .
May 25 17:18:12 biberbau kernel: [   42.663393] wlan0: authenticate
with 00:24:01:69:a9:31 (try 1)
May 25 17:18:12 biberbau kernel: [   42.665233] wlan0: authenticated
May 25 17:18:12 biberbau kernel: [   42.665414] wlan0: associate
with 00:24:01:69:a9:31 (try 1)
May 25 17:18:12 biberbau kernel: [   42.671353] wlan0: RX AssocResp
from 00:24:01:69:a9:31 (capab=0x431 status=0 aid=1)
May 25 17:18:12 biberbau kernel: [   42.671359] wlan0: associated
May 25 17:18:12 biberbau kernel: [   42.713457]
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
May 25 17:18:13 biberbau ifup-dhcp: .
May 25 17:18:15 biberbau ifup-dhcp: .
May 25 17:18:18 biberbau ifup-dhcp: .
May 25 17:18:18 biberbau dhcpcd[2202]: wlan0: offered 192.168.0.199
from 192.168.0.1
May 25 17:18:18 biberbau dhcpcd[2202]: wlan0: checking 192.168.0.199
is available on attached networks
May 25 17:18:19 biberbau dhcpcd[2202]: wlan0: leased 192.168.0.199
for 86400 seconds
May 25 17:18:19 biberbau dhcpcd[2202]: wlan0: adding IP address
192.168.0.199/24
May 25 17:18:19 biberbau dhcpcd[2202]: wlan0: adding default route
via 192.168.0.1 metric 0
May 25 17:18:20 biberbau ifdown:     wlan0     name: FRITZ!WLAN USB
Stick N
May 25 17:18:20 biberbau ifup:     wlan0     name: FRITZ!WLAN USB
Stick N
May 25 17:18:20 biberbau ifup-dhcp: .
May 25 17:18:20 biberbau SuSEfirewall2:
/var/lock/SuSEfirewall2.booting exists which means system boot in
progress, exit.
May 25 17:18:20 biberbau dhcpcd[2202]: wlan0: exiting
May 25 17:18:20 biberbau ifup-dhcp:
May 25 17:18:20 biberbau ifup-dhcp:     wlan0     IP address:
192.168.0.199/24
May 25 17:18:22 biberbau kernel: Kernel logging (proc) stopped.
May 25 17:18:22 biberbau rsyslogd: [origin software="rsyslogd"
swVersion="5.6.3" x-pid="974" x-info="http://www.rsyslog.com"]
exiting on signal 15.
May 25 17:18:22 biberbau kernel: imklog 5.6.3, log source =
/proc/kmsg started.
May 25 17:18:22 biberbau rsyslogd: [origin software="rsyslogd"
swVersion="5.6.3" x-pid="4040" x-info="http://www.rsyslog.com"] start
May 25 17:18:23 biberbau named[4119]: starting BIND 9.7.3 -t
/var/lib/named -u named
May 25 17:18:23 biberbau named[4119]: built with '--prefix=/usr'
'--bindir=/usr/bin' '--sbindir=/usr/sbin' '--sysconfdir=/etc'
'--localstatedir=/var' '--libdir=/usr/lib'
'--includedir=/usr/include/bind' '--mandir=/usr/share/man'
'--infodir=/usr/share/info' '--with-openssl' '--enable-threads'
'--with-libtool' '--enable-runidn' '--with-libxml2'
'--with-dlz-mysql' '--with-dlz-ldap' '--with-gssapi'
'CFLAGS=-fomit-frame-pointer -fmessage-length=0 -O2 -Wall
-D_FORTIFY_SOURCE=2 -fstack-protector -funwind-tables
-fasynchronous-unwind-tables -g -fno-strict-aliasing'
'LDFLAGS=-L/usr/lib'
May 25 17:18:23 biberbau named[4119]: adjusted limit on open files
from 8192 to 1048576
May 25 17:18:23 biberbau named[4119]: found 2 CPUs, using 2 worker
threads
May 25 17:18:23 biberbau named[4119]: using up to 4096 sockets
May 25 17:18:23 biberbau named[4119]: loading configuration from
'/etc/named.conf'
May 25 17:18:23 biberbau named[4119]: using default UDP/IPv4 port
range: [1024, 65535]
May 25 17:18:23 biberbau named[4119]: using default UDP/IPv6 port
range: [1024, 65535]
May 25 17:18:23 biberbau named[4119]: listening on IPv6 interfaces,
port 53
May 25 17:18:23 biberbau named[4119]: listening on IPv4 interface
lo, 127.0.0.1#53
May 25 17:18:23 biberbau named[4119]: listening on IPv4 interface
lo, 127.0.0.2#53
May 25 17:18:23 biberbau named[4119]: listening on IPv4 interface
wlan0, 192.168.0.199#53
May 25 17:18:23 biberbau named[4119]: generating session key for
dynamic DNS
May 25 17:18:23 biberbau named[4119]: set up managed keys zone for
view _default, file 'managed-keys.bind'
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
0.IN-ADDR.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
127.IN-ADDR.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
254.169.IN-ADDR.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
2.0.192.IN-ADDR.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
100.51.198.IN-ADDR.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
113.0.203.IN-ADDR.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
255.255.255.255.IN-ADDR.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.IP6.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.IP6.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone: D.F.IP6.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
8.E.F.IP6.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
9.E.F.IP6.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
A.E.F.IP6.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
B.E.F.IP6.ARPA
May 25 17:18:23 biberbau named[4119]: automatic empty zone:
8.B.D.0.1.0.0.2.IP6.ARPA
May 25 17:18:23 biberbau named[4119]: command channel listening on
127.0.0.1#953
May 25 17:18:23 biberbau named[4119]: command channel listening on
::1#953
May 25 17:18:23 biberbau named[4119]: the working directory is not
writable
May 25 17:18:23 biberbau named[4119]: zone 0.0.127.in-addr.arpa/IN:
loaded serial 42
May 25 17:18:23 biberbau named[4119]: zone
0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa/IN:
loaded serial 42
May 25 17:18:23 biberbau named[4119]: zone localhost/IN: loaded
serial 42
May 25 17:18:23 biberbau named[4119]: managed-keys-zone ./IN:
loading from master file managed-keys.bind failed: file not found
May 25 17:18:23 biberbau named[4119]: managed-keys-zone ./IN: loaded
serial 0
May 25 17:18:23 biberbau named[4119]: running
[ . . .]
May 25 17:18:33 biberbau acpid: client connected from 4426[0:0]
May 25 17:18:33 biberbau acpid: 1 client rule loaded
May 25 17:18:33 biberbau atieventsd[4426]: acpid connection established
May 25 17:18:33 biberbau /usr/sbin/cron[4456]: (CRON) STARTUP (1.4.6)
May 25 17:18:33 biberbau /usr/sbin/cron[4456]: (CRON) INFO (running
with inotify support)
May 25 17:18:33 biberbau SuSEfirewall2: Setting up rules from
/etc/sysconfig/SuSEfirewall2 ...
May 25 17:18:34 biberbau SuSEfirewall2: Firewall rules successfully set
[/Zitat Ende /var/log/messages]

Schlußbemerkung für heute:
Ich habe den Wlan-Stick an anderer Stelle aufgestellt. Jetzt steht
er 3 m
entfernt vom Router und es gibt es keine Hindernisse zwichen Router und
Wlan-Stick (Vorher Entfernung zum Router = 5 m , keine Hindernisse)
Kein Unterschied. (Der PC, der funktioniert, steht im Keller)

Grüße
Ernst

-- 
Um die Liste abzubestellen, schicken Sie eine Mail an:
    opensuse-de+unsubscribe@opensuse.org
Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken
Sie eine Mail an: opensuse-de+help@opensuse.org

Re: (..) Re: Wlan Speed - Up- und Download zu niedrig

Ernst Scott