Am Sonntag, 24. Februar 2008 16:06:59 schrieb Martin Schröder:
Installier die smartmontools und benutze sie.
Ich hab hier mal die Ausgabe von smartctl -a /dev/sda eingefügt. Ich sehe da errors, bloß werd ich nicht so recht schlau draus. Ein -t long läuft gerade. Ergebnis folgt. Bodo smartctl -a /dev/sda smartctl version 5.37 [i686-suse-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: IBM/Hitachi Travelstar 60GH and 40GN family Device Model: IC25N020ATCS04-0 Serial Number: CSH209DGDB9A7F Firmware Version: CA2OA71A User Capacity: 20.003.880.960 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 5 ATA Standard is: ATA/ATAPI-5 T13 1321D revision 3 Local Time is: Sun Feb 24 16:33:50 2008 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 645) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 26) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0 3 Spin_Up_Time 0x0007 144 144 033 Pre-fail Always - 1 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 1464 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0 9 Power_On_Hours 0x0012 097 097 000 Old_age Always - 1683 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1257 191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 140 193 Load_Cycle_Count 0x0012 097 097 000 Old_age Always - 35089 194 Temperature_Celsius 0x0002 127 127 000 Old_age Always - 43 (Lifetime Min/Max 11/57) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 3 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 95 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 95 occurred at disk power-on lifetime: 1645 hours (68 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 02 85 33 8a e1 Error: UNC 2 sectors at LBA = 0x018a3385 = 25834373 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 7f 33 8a e1 00 04:56:04.900 READ DMA ca 00 08 3f e9 72 e0 00 04:56:04.900 WRITE DMA c8 00 08 7f 33 8a e1 00 04:56:00.400 READ DMA ca 00 60 df e8 72 e0 00 04:56:00.400 WRITE DMA ca 00 08 37 32 ea e0 00 04:56:00.400 WRITE DMA Error 94 occurred at disk power-on lifetime: 1645 hours (68 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 02 85 33 8a e1 Error: UNC 2 sectors at LBA = 0x018a3385 = 25834373 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 7f 33 8a e1 00 04:56:00.400 READ DMA ca 00 60 df e8 72 e0 00 04:56:00.400 WRITE DMA ca 00 08 37 32 ea e0 00 04:56:00.400 WRITE DMA ca 00 08 7f 31 ea e0 00 04:56:00.400 WRITE DMA ca 00 08 d7 e8 72 e0 00 04:56:00.400 WRITE DMA Error 93 occurred at disk power-on lifetime: 1645 hours (68 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 02 d5 31 8a e1 Error: UNC 2 sectors at LBA = 0x018a31d5 = 25833941 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 cf 31 8a e1 00 04:55:55.700 READ DMA ca 00 08 37 32 ea e0 00 04:55:55.700 WRITE DMA ca 00 08 b7 5b 70 e0 00 04:55:55.700 WRITE DMA ca 00 08 5f 63 84 e1 00 04:55:55.700 WRITE DMA ca 00 10 c7 5b 84 e1 00 04:55:55.700 WRITE DMA Error 92 occurred at disk power-on lifetime: 1645 hours (68 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 02 d5 31 8a e1 Error: UNC 2 sectors at LBA = 0x018a31d5 = 25833941 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 cf 31 8a e1 00 04:55:51.100 READ DMA ca 00 18 e7 e7 72 e0 00 04:55:51.100 WRITE DMA ca 00 08 37 32 ea e0 00 04:55:51.100 WRITE DMA ca 00 08 7f 31 ea e0 00 04:55:51.100 WRITE DMA ca 00 08 df e7 72 e0 00 04:55:51.100 WRITE DMA Error 91 occurred at disk power-on lifetime: 1645 hours (68 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 02 25 30 8a e1 Error: UNC 2 sectors at LBA = 0x018a3025 = 25833509 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 1f 30 8a e1 00 04:55:46.500 READ DMA ca 00 f0 1f e6 72 e0 00 04:55:46.500 WRITE DMA ca 00 08 37 32 ea e0 00 04:55:46.500 WRITE DMA c8 00 08 1f 30 8a e1 00 04:55:42.000 READ DMA c8 00 18 27 73 e9 e0 00 04:55:42.000 READ DMA SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Device does not support Selective Self Tests/Logging -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org