Hallo Leute, Beim Brennen eine CD mit x-cd-roast-0.98alpha10 unter SuSE 8.0 bekomme ich den Fehler OPC failed mit einem Plextor Brenner (PX-W2410A, Revision: 1.03) und einer maxell CD-RW. Wenn ich einer anderen RW-Rohling nehmen, von Plextor, dann geht es. Wenn ich den Rohling der nehme der mit dem Plextor nicht tat und in eimen HP Brenner verwende (CD-Writer+ 8200, Revision: 1.0f) gibt es ebenfalls keine Probleme. Allerdings habe ich auf der maxell CD einen winzigen Aufdruck gefunden: 'For music use only' mach das evt. was aus? Wenn ja warum nur bei dem Plextor Brenner? Vielen Dank Michael --- Löschen einer RW (maxell) mit Plextor Brenner scsidev: '1,0,0' scsibus: 1 target: 0 lun: 0 Linux sg driver version: 3.1.22 Cdrecord 1.11a19 (i686-pc-linux-gnu) Copyright (C) 1995-2002 Jörg Schilling TOC Type: 1 = CD-ROM Using libscg version 'schily-0.6' atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 1 Vendor_info : 'PLEXTOR ' Identifikation : 'CD-R PX-W2410A' Revision : '1.03' Device seems to be: Generic mmc CD-RW. Using generic SCSI-3/mmc CD-R driver (mmc_cdr). Driver flags : SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 4194304 = 4096 KB Current Secsize: 2048 ATIP info from disk: Indicated writing power: 5 Reference speed: 2 Is unrestricted Is erasable ATIP start of lead in: -11635 (97:26/65) ATIP start of lead out: 335175 (74:31/00) speed low: 2 speed high: 2 power mult factor: 5 6 recommended erase/write power: 3 Disk type: Phase change Manuf. index: 3 Manufacturer: CMC Magnetics Corporation Blocks total: 335175 Blocks current: 335175 Blocks remaining: 335325 Starting to write CD/DVD at speed 4 in write mode for single session. 0 seconds. Operation starts. cdrecord: OPC failed. Performing OPC... Blanking PMA, TOC, pregap Blanking time: 49.094s ---- Brennen einer RW (maxell) mit Plextor Brenner: scsidev: '1,0,0' scsibus: 1 target: 0 lun: 0 Linux sg driver version: 3.1.22 Cdrecord 1.11a19 (i686-pc-linux-gnu) Copyright (C) 1995-2002 Jörg Schilling TOC Type: 1 = CD-ROM Using libscg version 'schily-0.6' atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 1 Vendor_info : 'PLEXTOR ' Identifikation : 'CD-R PX-W2410A' Revision : '1.03' Device seems to be: Generic mmc CD-RW. Using generic SCSI-3/mmc CD-R driver (mmc_cdr). Driver flags : SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 2394336 = 2338 KB Current Secsize: 2048 ATIP info from disk: Indicated writing power: 5 Reference speed: 2 Is unrestricted Is erasable ATIP start of lead in: -11635 (97:26/65) ATIP start of lead out: 335175 (74:31/00) speed low: 2 speed high: 2 power mult factor: 5 6 recommended erase/write power: 3 Disk type: Phase change Manuf. index: 3 Manufacturer: CMC Magnetics Corporation Blocks total: 1166730 Blocks current: 1166730 Blocks remaining: 1166880 Starting to write CD/DVD at speed 4 in write mode for single session. 0 seconds. Operation starts. cdrecord: OPC failed. Performing OPC... Blanking PMA, TOC, pregap cdrecord: Input/output error. blank unit: scsi sendcmd: no error CDB: A1 01 00 00 00 00 00 00 00 00 00 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 03 00 00 00 00 0A 00 00 00 00 73 03 00 00 Sense Key: 0x3 Medium Error, Segment 0 Sense Code: 0x73 Qual 0x03 (power calibration area error) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 12.009s timeout 9600s cdrecord: Cannot blank disk, aborting.