Hallo, mein Megaraid 9271-8i Controller piepst und zeigt im Storage Manager auch an, dass ein Alarm aktiv ist. Darüber hinaus aber keinen Fehler. Alle VDs sind in optimalem Zustand. Eine Suppor-Anfrage bei Broadcom wird aus welchen Gründen auch immer nicht abgesendet, obwohl das Webformular an jedem Eintrag einen grünen Haken schreibt. Der Controller hat die aktuelleste Firmware. Angeschlossen sind 6 SAS HDs im RAID 10 mit je einer Hot Spare. Außerdem 2 SSDsf im Raid 1 als Cache. Hat jemand eine Idee wie ich den Fehler lokalisieren und beheben kann. Neustart und Spannungswechslel waren erfolglos. Oder kennt jemand ein Forum, in dem solchte Themen besprochen werden? -- Dirk Nachstehend die Controllerdaten: Generating detailed summary of the adapter, it may take a while to complete. Controller = 0 Status = Success Description = None Basics : ====== Controller = 0 Model = LSI MegaRAID SAS 9271-8i Serial Number = SV42432893 Current Controller Date/Time = 02/17/2024, 14:53:51 Current System Date/time = 02/17/2024, 14:53:51 SAS Address = 500605b008f770d0 PCI Address = 00:05:00:00 Mfg Date = 06/12/14 Rework Date = 00/00/00 Revision No = 28A Version : ======= Firmware Package Build = 23.34.0-0019 Firmware Version = 3.460.115-6465 Bios Version = 5.50.03.0_4.17.08.00_0x06110200 WebBIOS Version = 6.1-76-e_76-Rel Preboot CLI Version = 05.07-00:#%00011 NVDATA Version = 2.1507.03-0162 Boot Block Version = 2.05.00.00-0010 Bootloader Version = 07.26.26.219 Driver Name = megaraid_sas Driver Version = 07.713.01.00-rc1 Bus : === Vendor Id = 0x1000 Device Id = 0x5B SubVendor Id = 0x1000 SubDevice Id = 0x9271 Host Interface = PCI-E Device Interface = SAS-6G Bus Number = 5 Device Number = 0 Function Number = 0 Pending Images in Flash : ======================= Image name = No pending images Status : ====== Controller Status = Optimal Memory Correctable Errors = 0 Memory Uncorrectable Errors = 0 ECC Bucket Count = 0 Any Offline VD Cache Preserved = No BBU Status = 0 Support PD Firmware Download = No Lock Key Assigned = No Failed to get lock key on bootup = No Lock key has not been backed up = No Bios was not detected during boot = No Controller must be rebooted to complete security operation = No A rollback operation is in progress = No At least one PFK exists in NVRAM = Yes SSC Policy is WB = Yes Controller has booted into safe mode = No Supported Adapter Operations : ============================ Rebuild Rate = Yes CC Rate = Yes BGI Rate = Yes Reconstruct Rate = Yes Patrol Read Rate = Yes Alarm Control = Yes Cluster Support = No BBU = Yes Spanning = Yes Dedicated Hot Spare = Yes Revertible Hot Spares = Yes Foreign Config Import = Yes Self Diagnostic = Yes Allow Mixed Redundancy on Array = No Global Hot Spares = Yes Deny SCSI Passthrough = No Deny SMP Passthrough = No Deny STP Passthrough = No Support more than 8 Phys = Yes FW and Event Time in GMT = No Support Enhanced Foreign Import = Yes Support Enclosure Enumeration = Yes Support Allowed Operations = Yes Abort CC on Error = Yes Support Multipath = Yes Support Odd & Even Drive count in RAID1E = No Support Security = No Support Config Page Model = Yes Support the OCE without adding drives = Yes Support EKM = No Snapshot Enabled = No Support PFK = Yes Support PI = Yes Support LDPI Type1 = No Support LDPI Type2 = No Support LDPI Type3 = No Support Ld BBM Info = No Support Shield State = Yes Block SSD Write Disk Cache Change = No Support Suspend Resume BG ops = Yes Support Emergency Spares = No Support Set Link Speed = Yes Support Boot Time PFK Change = No Support JBOD = No Disable Online PFK Change = No Support Perf Tuning = Yes Support SSD PatrolRead = Yes Real Time Scheduler = Yes Support Reset Now = Yes Support Emulated Drives = Yes Headless Mode = Yes Dedicated HotSpares Limited = No Point In Time Progress = Yes Extended LD = Yes Boot Volume Supported = No Support Uneven span = No Support Config Auto Balance = No Support Maintenance Mode = No Support Diagnostic results = No Support Ext Enclosure = Yes Support Sesmonitoring = No Support SecurityonJBOD = No Support ForceFlash = No Support DisableImmediateIO = No Support LargeIOSupport = No Support DrvActivityLEDSetting = Yes Support FlushWriteVerify = Yes Support CPLDUpdate = No Support ForceTo512e = Yes Support discardCacheDuringLDDelete = No Support JBOD Write cache = No Support Large QD Support = No Support SRIOV Options = No Supported PD Operations : ======================= Force Online = Yes Force Offline = Yes Force Rebuild = Yes Deny Force Failed = No Deny Force Good/Bad = No Deny Missing Replace = No Deny Clear = No Deny Locate = No Support Power State = Yes Set Power State For Cfg = No Support T10 Power State = No Support Temperature = Yes NCQ = Yes Support Max Rate SATA = No Support Degraded Media = No Support Parallel FW Update = No Support Drive Crypto Erase = No Supported VD Operations : ======================= Read Policy = Yes Write Policy = Yes IO Policy = Yes Access Policy = Yes Disk Cache Policy = Yes Reconstruction = Yes Deny Locate = No Deny CC = No Allow Ctrl Encryption = No Enable LDBBM = No Support FastPath = Yes Performance Metrics = Yes Power Savings = No Support Powersave Max With Cache = No Support Breakmirror = No Support SSC WriteBack = Yes Support SSC Association = Yes Support VD Hide = No Support VD Cachebypass = No Support VD discardCacheDuringLDDelete = No Advanced Software Option : ======================== -------------------------------------------------------------- Adv S/W Opt Time Remaining Mode -------------------------------------------------------------- MegaRAID FastPath Unlimited Secured MegaRAID CacheCade Pro 2.0 Unlimited Secured MegaRAID RAID6 Unlimited Factory Installed MegaRAID RAID5 Unlimited Factory Installed Cache Offload Unlimited Factory Installed -------------------------------------------------------------- Safe ID = 95C8A1TVM2X9UJTEGN74D1VKQVGRCM6AF2HCP6RZ HwCfg : ===== ChipRevision = D1 BatteryFRU = N/A Front End Port Count = 0 Backend Port Count = 8 BBU = Present Alarm = On Serial Debugger = Present NVRAM Size = 32KB Flash Size = 16MB On Board Memory Size = 1024MB CacheVault Flash Size = NA TPM = Absent Upgrade Key = Present On Board Expander = Absent Temperature Sensor for ROC = Present Temperature Sensor for Controller = Absent Upgradable CPLD = Absent Current Size of CacheCade (GB) = 73 Current Size of FW Cache (MB) = 787 ROC temperature(Degree Celsius) = 76 Policies : ======== Policies Table : ============== ------------------------------------------------ Policy Current Default ------------------------------------------------ Predictive Fail Poll Interval 300 sec Interrupt Throttle Active Count 16 Interrupt Throttle Completion 50 us Rebuild Rate 30 % 30% PR Rate 30 % 30% BGI Rate 30 % 30% Check Consistency Rate 30 % 30% Reconstruction Rate 30 % 30% Cache Flush Interval 4s ------------------------------------------------ Flush Time(Default) = 4s Drive Coercion Mode = 1GB Auto Rebuild = On Battery Warning = On ECC Bucket Size = 15 ECC Bucket Leak Rate (hrs) = 24 Restore HotSpare on Insertion = Off Expose Enclosure Devices = On Maintain PD Fail History = Off Reorder Host Requests = On Auto detect BackPlane = SGPIO/i2c SEP Load Balance Mode = Auto Security Key Assigned = Off Disable Online Controller Reset = Off Use drive activity for locate = On Boot : ==== BIOS Enumerate VDs = 1 Stop BIOS on Error = Off Delay during POST = 0 Spin Down Mode = Internal Only Enable Ctrl-R = No Enable Web BIOS = Yes Enable PreBoot CLI = Yes Enable BIOS = No Max Drives to Spinup at One Time = 2 Maximum number of direct attached drives to spin up in 1 min = 10 Delay Among Spinup Groups (sec) = 12 Allow Boot with Preserved Cache = Off High Availability : ================= Topology Type = None Cluster Permitted = No Cluster Active = No Defaults : ======== Phy Polarity = 0 Phy PolaritySplit = 0 Strip Size = 64 KB Write Policy = WB Read Policy = RA Cache When BBU Bad = Off Cached IO = Off VD PowerSave Policy = Automatic Default spin down time (mins) = 30 Coercion Mode = 1 GB ZCR Config = Unknown Max Chained Enclosures = 16 Direct PD Mapping = No Restore Hot Spare on Insertion = No Expose Enclosure Devices = Yes Maintain PD Fail History = No Zero Based Enclosure Enumeration = No Disable Puncturing = No EnableLDBBM = No DisableHII = No Un-Certified Hard Disk Drives = Allow SMART Mode = Mode 6 Enable LED Header = No LED Show Drive Activity = No Dirty LED Shows Drive Activity = No EnableCrashDump = No Disable Online Controller Reset = No Treat Single span R1E as R10 = No Power Saving option = Enabled TTY Log In Flash = Yes Auto Enhanced Import = Yes BreakMirror RAID Support = No Disable Join Mirror = No Enable Shield State = No Time taken to detect CME = 60 sec Capabilities : ============ Supported Drives = SAS, SATA Boot Volume Supported = NO RAID Level Supported = RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50, RAID60, PRL 11, PRL 11 with spanning, SRL 3 supported, PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span Enable JBOD = No Mix in Enclosure = Allowed Mix of SAS/SATA of HDD type in VD = Allowed Mix of SAS/SATA of SSD type in VD = Allowed Mix of SSD/HDD in VD = Not Allowed SAS Disable = No Max Arms Per VD = 32 Max Spans Per VD = 8 Max Arrays = 128 Max VD per array = 64 Max Number of VDs = 64 Max Parallel Commands = 1008 Max SGE Count = 60 Max Data Transfer Size = 8192 sectors Max Strips PerIO = 42 Max Configurable CacheCade Size(GB) = 512 Max Transportable DGs = 0 Min Strip Size = 8 KB Max Strip Size = 1.0 MB Scheduled Tasks : =============== Consistency Check Reoccurrence = 168 hrs Next Consistency check launch = 02/20/2024, 21:00:00 Patrol Read Reoccurrence = 168 hrs Next Patrol Read launch = 02/22/2024, 00:00:00 Battery learn Reoccurrence = 670 hrs Next Battery Learn = 03/09/2024, 02:00:00 OEMID = LSI Drive Groups = 2 TOPOLOGY : ======== ------------------------------------------------------------------------------ DG Arr Row EID:Slot DID Type State BT Size PDC PI SED DS3 FSpace TR ------------------------------------------------------------------------------ 0 - - - - RAID10 Optl N 14.553 TB dsbl N N none N N 0 0 - - - RAID1 Optl N 7.276 TB dsbl N N none N N 0 0 0 252:0 34 DRIVE Onln N 7.276 TB dsbl N N none - N 0 0 1 252:4 38 DRIVE Onln N 7.276 TB dsbl N N none - N 0 1 - - - RAID1 Optl N 7.276 TB dsbl N N none N N 0 1 0 252:1 33 DRIVE Onln N 7.276 TB dsbl N N none - N 0 1 1 252:5 35 DRIVE Onln N 7.276 TB dsbl N N none - N 0 - - 252:2 36 DRIVE DHS - 7.276 TB - - - - - N 1 - - - - Cac1 Optl N 73.574 GB dflt N N none N N 1 0 - - - RAID1 Optl N 73.574 GB dflt N N none N N 1 0 0 252:3 32 DRIVE Onln N 73.574 GB dflt N N none - N 1 0 1 252:7 27 DRIVE Onln N 222.585 GB dflt N N none - N ------------------------------------------------------------------------------ DG=Disk Group Index|Arr=Array Index|Row=Row Index|EID=Enclosure Device ID DID=Device ID|Type=Drive Type|Onln=Online|Rbld=Rebuild|Dgrd=Degraded Pdgd=Partially degraded|Offln=Offline|BT=Background Task Active PDC=PD Cache|PI=Protection Info|SED=Self Encrypting Drive|Frgn=Foreign DS3=Dimmer Switch 3|dflt=Default|Msng=Missing|FSpace=Free Space Present TR=Transport Ready Virtual Drives = 2 VD LIST : ======= ---------------------------------------------------------------- DG/VD TYPE State Access Consist Cache Cac sCC Size Name ---------------------------------------------------------------- 0/0 RAID10 Optl RW Yes NRAWBD RW ON 14.553 TB 1/1 Cac1 Optl RW Yes NRWBD - ON 73.574 GB ---------------------------------------------------------------- Cac=CacheCade|Rec=Recovery|OfLn=OffLine|Pdgd=Partially Degraded|Dgrd=Degraded Optl=Optimal|RO=Read Only|RW=Read Write|HD=Hidden|TRANS=TransportReady| B=Blocked| Consist=Consistent|R=Read Ahead Always|NR=No Read Ahead|WB=WriteBack| AWB=Always WriteBack|WT=WriteThrough|C=Cached IO|D=Direct IO|sCC=Scheduled Check Consistency Physical Drives = 8 PD LIST : ======= --------------------------------------------------------------------------------- EID:Slt DID State DG Size Intf Med SED PI SeSz Model Sp Type --------------------------------------------------------------------------------- 252:0 34 Onln 0 7.276 TB SAS HDD N N 512B HUH728080AL5200 U - 252:1 33 Onln 0 7.276 TB SAS HDD N N 512B HUH728080AL5200 U - 252:2 36 DHS 7.276 TB SAS HDD N N 512B HUH728080AL5200 U - 252:3 32 Onln 1 73.574 GB SATA SSD N N 512B INTEL SSDSC2BB080G6 U - 252:4 38 Onln 0 7.276 TB SAS HDD N N 512B HUH728080AL5200 U - 252:5 35 Onln 0 7.276 TB SAS HDD N N 512B HUH728080AL5200 U - 252:6 37 DHS 7.276 TB SAS HDD N N 512B HUH728080AL5200 U - 252:7 27 Onln 1 222.585 GB SATA SSD N N 512B INTEL SSDSC2KB240G8 U - --------------------------------------------------------------------------------- EID-Enclosure Device ID|Slt-Slot No.|DID-Device ID|DG-DriveGroup DHS-Dedicated Hot Spare|UGood-Unconfigured Good|GHS-Global Hotspare UBad-Unconfigured Bad|Onln-Online|Offln-Offline|Intf-Interface Med-Media Type|SED-Self Encryptive Drive|PI-Protection Info SeSz-Sector Size|Sp-Spun|U-Up|D-Down|T-Transition|F-Foreign UGUnsp-Unsupported|UGShld-UnConfigured shielded|HSPShld-Hotspare shielded CFShld-Configured shielded|Cpybck-CopyBack|CBShld-Copyback Shielded Cachevault_Info : =============== --------------------------------------------------------- Model State Temp Mode MfgDate Next Learn --------------------------------------------------------- CVPM02 Optimal 38C - 2015/03/27 2024/03/09 02:15:55 --------------------------------------------------------- seqNum: 0x00012ac3 Time: Mon Nov 7 02:49:58 2022 Code: 0x000000fb Class: 2 Locale: 0x01 Event Description: VD 00/0 is now DEGRADED Event Data: =========== Target Id: 0 seqNum: 0x00012ace Time: Mon Nov 7 02:51:02 2022 Code: 0x00000159 Class: 2 Locale: 0x20 Event Description: Controller encountered a fatal error and was reset Event Data: =========== None seqNum: 0x000151ee Time: Sat Jul 1 08:37:17 2023 Code: 0x000000fb Class: 2 Locale: 0x01 Event Description: VD 01/1 is now DEGRADED Event Data: =========== Target Id: 1 seqNum: 0x00015420 Seconds since last reboot: 83 Code: 0x000000fb Class: 2 Locale: 0x01 Event Description: VD 01/1 is now DEGRADED Event Data: =========== Target Id: 1 Controller = 0 Status = Success Description = None Events = GETEVENTS Controller Properties : ===================== ------------------------------------ Ctrl Status Method Value ------------------------------------ 0 Success handleSuboption Events