Re: Aldi-Kartenleser streikt unter SuSE 8.2

16 Aug 2003

      Am Donnerstag, 14. August 2003 22:05 schrieb Christian Boltz:
...
Hallo Frank, hallo H.-Peter, hallo Leute,
Am Montag, 11. August 2003 17:06 schrieb Frank Zündorff:
...
Am Sonntag, 10. August 2003 15:54 schrieb H.-Peter Baldamus:
...
Am Freitag, 8. August 2003 19:44 schrieb Frank Zündorff:
...
Bin ich wirklich der einzige hier, der seinen Kartenlesen
nicht ans Rennen bekommt?
Nein! Ich bekomme jedoch nicht den von Aldi, sondern den von
Typhoon nicht zum Rennen.
Oh, ein Leidensgenosse. Wie sind die Symthome bei Dir?
Die sind bei Euch beiden leider gleich - Ihr habt beide einen
Kartenleser, der nicht so recht will, und beide liefert Ihr keine
Auszüge aus /var/log/messages
- beim Anstöpseln des Readers
- beim Einstecken einer Speicherkarte
- beim Mountversuch
Nun habe ich mich auch entschlossen, wie Frank, die beiden Auszüge 
zu liefern (wahnsinnig lang; beschränke mich auf's notwendigste).

/var/log/messages nach Stöpseln mit SecureDigital-Karte (in anderen 
USB-Anschluß):
Aug 16 12:04:14 xxxx kernel: usb.c: USB disconnect on device 
00:03.1-1.5 address 6
Aug 16 12:05:15 xxxx kernel: hub.c: new USB device 00:03.0-2, 
assigned address 4
Aug 16 12:05:15 xxxx kernel: usb.c: USB device 4 (vend/prod 
0x7cc/0x200) is not claimed by any active driver.
Aug 16 12:05:19 xxxx kernel: Initializing USB Mass Storage driver...
Aug 16 12:05:19 xxxx kernel: usb.c: registered new driver 
usb-storage
Aug 16 12:05:19 xxxx kernel: scsi1 : SCSI emulation for USB Mass 
Storage devices
Aug 16 12:05:19 xxxx kernel:   Vendor: SPRING    Model: MultiCard 
Slot A  Rev: 0100
Aug 16 12:05:19 xxxx kernel:   Type:   Direct-Access                      
ANSI SCSI revision: 02
Aug 16 12:05:19 xxxx kernel:   Vendor: SPRING    Model: MultiCard 
Slot D  Rev: 0100
Aug 16 12:05:19 xxxx kernel:   Type:   Direct-Access                      
ANSI SCSI revision: 02
Aug 16 12:05:19 xxxx kernel:   Vendor: SPRING    Model: MultiCard 
Slot S  Rev: 0100
Aug 16 12:05:19 xxxx kernel:   Type:   Direct-Access                      
ANSI SCSI revision: 02
Aug 16 12:05:19 xxxx kernel:   Vendor: SPRING    Model: MultiCard 
Slot M  Rev: 0100
Aug 16 12:05:19 xxxx kernel:   Type:   Direct-Access                      
ANSI SCSI revision: 02
Aug 16 12:05:19 xxxx kernel: Attached scsi removable disk sda at 
scsi1, channel 0, id 0, lun 0
Aug 16 12:05:19 xxxx kernel: Attached scsi removable disk sdb at 
scsi1, channel 0, id 0, lun 1
Aug 16 12:05:19 xxxx kernel: Attached scsi removable disk sdc at 
scsi1, channel 0, id 0, lun 2
Aug 16 12:05:19 xxxx kernel: Attached scsi removable disk sdd at 
scsi1, channel 0, id 0, lun 3
Aug 16 12:05:19 xxxx kernel: sda : READ CAPACITY failed.
Aug 16 12:05:19 xxxx kernel: sda : status = 1, message = 00, host = 
0, driver = 08
Aug 16 12:05:19 xxxx kernel: Current sd00:00: sns = 70  2
Aug 16 12:05:19 xxxx kernel: ASC=3a ASCQ= 0
Aug 16 12:05:19 xxxx kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 
0x00 0x00 0x10 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
0x00 0x00 0x00 0x00 0x00 0x00
Aug 16 12:05:19 xxxx kernel: sda : block size assumed to be 512 
bytes, disk size 1GB.
Aug 16 12:05:19 xxxx kernel:  sda: I/O error: dev 08:00, sector 0
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:00, sector 0
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:00, sector 2097144
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:00, sector 2097144
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:00, sector 0
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:00, sector 0
Aug 16 12:05:19 xxxx kernel:  unable to read partition table
Aug 16 12:05:19 xxxx kernel: SCSI device sdb: 124160 512-byte hdwr 
sectors (64 MB)
Aug 16 12:05:19 xxxx kernel: sdb: Write Protect is off
Aug 16 12:05:19 xxxx kernel:  sdb: sdb1
Aug 16 12:05:19 xxxx kernel: sdc : READ CAPACITY failed.
Aug 16 12:05:19 xxxx kernel: sdc : status = 1, message = 00, host = 
0, driver = 08
Aug 16 12:05:19 xxxx kernel: Current sd00:00: sns = 70  2
Aug 16 12:05:19 xxxx kernel: ASC=3a ASCQ= 0
Aug 16 12:05:19 xxxx kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 
0x00 0x00 0x10 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
0x00 0x00 0x00 0x00 0x00 0x00
Aug 16 12:05:19 xxxx kernel: sdc : block size assumed to be 512 
bytes, disk size 1GB.
Aug 16 12:05:19 xxxx kernel:  sdc: I/O error: dev 08:20, sector 0
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:20, sector 0
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:20, sector 2097144
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:20, sector 2097144
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:20, sector 0
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:20, sector 0
Aug 16 12:05:19 xxxx kernel:  unable to read partition table
Aug 16 12:05:19 xxxx kernel: sdd : READ CAPACITY failed.
Aug 16 12:05:19 xxxx kernel: sdd : status = 1, message = 00, host = 
0, driver = 08
Aug 16 12:05:19 xxxx kernel: Current sd00:00: sns = 70  2
Aug 16 12:05:19 xxxx kernel: ASC=3a ASCQ= 0
Aug 16 12:05:19 xxxx kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 
0x00 0x00 0x10 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
0x00 0x00 0x00 0x00 0x00 0x00
Aug 16 12:05:19 xxxx kernel: sdd : block size assumed to be 512 
bytes, disk size 1GB.
Aug 16 12:05:19 xxxx kernel:  sdd: I/O error: dev 08:30, sector 0
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:30, sector 0
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:30, sector 2097144
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:30, sector 2097144
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:30, sector 0
Aug 16 12:05:19 xxxx kernel:  I/O error: dev 08:30, sector 0
Aug 16 12:05:19 xxxx kernel:  unable to read partition table
Aug 16 12:05:19 xxxx kernel: WARNING: USB Mass Storage data Aug 16 
integrity not assured
Aug 16 12:05:19 xxxx kernel: USB Mass Storage device found at 4
Aug 16 12:05:19 xxxx kernel: USB Mass Storage support registered.
Aug 16 12:05:19 xxxx insmod: Using 
/lib/modules/2.4.20-4GB-athlon/kernel/drivers/usb/storage/usb-storage.o
12:05:19 peti insmod: Symbol version prefix ''

[..] Jetzt wird beschrieben, daß sda, sdc, sdd keine Karte hat

Aug 16 12:05:20 xxxx /etc/hotplug/usb.agent[2688]: Can't ignore 
signal CHLD, forcing to default.
Aug 16 12:05:20 xxxx kernel: SCSI error: host 1 id 0 lun 2 return 
code = 8000002
Aug 16 12:05:20 xxxx kernel:    Sense class 7, sense error 0, 
extended sense 0
Aug 16 12:05:20 xxxx kernel: sdc : READ CAPACITY failed.
Aug 16 12:05:20 xxxx kernel: sdc : status = 1, message = 00, host = 
0, driver = 08
Aug 16 12:05:20 xxxx kernel: Current sd00:00: sns = 70  2
Aug 16 12:05:20 xxxx kernel: ASC=3a ASCQ= 0
Aug 16 12:05:20 xxxx kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 
0x00 0x00 0x10 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
0x00 0x00 0x00 0x00 0x00 0x00
Aug 16 12:05:20 xxxx kernel: sdc : block size assumed to be 512 
bytes, disk size 1GB.
Aug 16 12:05:20 xxxx kernel:  sdc: I/O error: dev 08:20, sector 0
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:20, sector 0
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:20, sector 2097144
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:20, sector 2097144
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:20, sector 0
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:20, sector 0
Aug 16 12:05:20 xxxx kernel:  unable to read partition table
Aug 16 12:05:20 xxxx kernel: SCSI error: host 1 id 0 lun 0 return 
code = 8000002
Aug 16 12:05:20 xxxx kernel:    Sense class 7, sense error 0, 
extended sense 0
Aug 16 12:05:20 xxxx kernel: sda : READ CAPACITY failed.
Aug 16 12:05:20 xxxx kernel: sda : status = 1, message = 00, host = 
0, driver = 08
Aug 16 12:05:20 xxxx kernel: Current sd00:00: sns = 70  2
Aug 16 12:05:20 xxxx kernel: ASC=3a ASCQ= 0
Aug 16 12:05:20 xxxx kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 
0x00 0x00 0x10 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
0x00 0x00 0x00 0x00 0x00 0x00
Aug 16 12:05:20 xxxx kernel: sda : block size assumed to be 512 
bytes, disk size 1GB.
Aug 16 12:05:20 xxxx kernel:  sda: I/O error: dev 08:00, sector 0
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:00, sector 0
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:00, sector 2097144
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:00, sector 2097144
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:00, sector 0
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:00, sector 0
Aug 16 12:05:20 xxxx kernel:  unable to read partition table
Aug 16 12:05:20 xxxx kernel: SCSI error: host 1 id 0 lun 3 return 
code = 8000002
Aug 16 12:05:20 xxxx kernel:    Sense class 7, sense error 0, 
extended sense 0
Aug 16 12:05:20 xxxx kernel: sdd : READ CAPACITY failed.
Aug 16 12:05:20 xxxx kernel: sdd : status = 1, message = 00, host = 
0, driver = 08
Aug 16 12:05:20 xxxx kernel: Current sd00:00: sns = 70  2
Aug 16 12:05:20 xxxx kernel: ASC=3a ASCQ= 0
Aug 16 12:05:20 xxxx kernel: Raw sense data:0x70 0x00 0x02 0x00 0x00 
0x00 0x00 0x10 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
0x00 0x00 0x00 0x00 0x00 0x00
Aug 16 12:05:20 xxxx kernel: sdd : block size assumed to be 512 
bytes, disk size 1GB.
Aug 16 12:05:20 xxxx kernel:  sdd: I/O error: dev 08:30, sector 0
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:30, sector 0
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:30, sector 2097144
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:30, sector 2097144
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:30, sector 0
Aug 16 12:05:20 xxxx kernel:  I/O error: dev 08:30, sector 0
Aug 16 12:05:20 xxxx kernel:  unable to read partition table

Also Gerät erkannt, sdb1 aber nicht mountbar! Symbol auf Desktop 
angelegt. Klick bringt den Hinweis
mount: Falscher Dateisystemtyp, ungültige Optionen, der
»Superblock« von /dev/sdb1 ist beschädigt oder es sind
zu viele Dateisysteme eingehängt. - na prima - , in /etc/fstab ist 
der Hotplug-Eintrag vorhanden.

/lsusb -v liefert:
[...]
Bus 003 Device 004: ID 07cc:0200 Carry Computer Eng., Co., Ltd 
6-in-1 Card Reader
  Language IDs: none (invalid length string descriptor bf; len=0)
string descriptor 1 invalid (bf bf; len=0)
string descriptor 2 invalid (bf bf; len=0)
string descriptor 3 invalid (bf bf; len=0)
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 Interface
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x07cc Carry Computer Eng., Co., Ltd
  idProduct          0x0200 6-in-1 Card Reader
  bcdDevice            0.12
  iManufacturer           1
  iProduct                2
  iSerial                 3
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           39
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          4
    bmAttributes         0x80
    MaxPower              100mA
string descriptor 5 invalid (bf bf; len=0)
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk (Zip)
      iInterface              5
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               none
        wMaxPacketSize         64
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               none
        wMaxPacketSize         64
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               none
        wMaxPacketSize          8
        bInterval              10
  Language IDs: none (invalid length string descriptor bf; len=0)
[...]

Christian (oder ....), kannst Du was damit anfangen? Vielleicht 
sogar helfen?

Grüße
H.-Peter