After my tumbleweed upgrade last week, I am no longer able to boot into my system unless I use the 'nomodeset' configuration. In that case, I cannot get into a graphical target at all. This has only happened since the kernel upgrade to 4.19. Here is my hardware information # hwinfo --gfxcard 23: PCI 300.0: 0380 Display controller [Created at pci.378] Unique ID: svHJ.+ug88O0PpPA Parent ID: w+J7.XZwpGIabNM5 SysFS ID: /devices/pci0000:00/0000:00:03.1/0000:03:00.0 SysFS BusID: 0000:03:00.0 Hardware Class: graphics card Model: "ATI Baffin [Radeon RX 460]" Vendor: pci 0x1002 "ATI Technologies Inc" Device: pci 0x67ef "Baffin [Radeon RX 460]" SubVendor: pci 0x1028 "Dell" SubDevice: pci 0x07e2 Revision: 0xff Driver: "amdgpu" Driver Modules: "amdgpu" Memory Range: 0xe0000000-0xefffffff (ro,non-prefetchable) Memory Range: 0xf0000000-0xf01fffff (ro,non-prefetchable) I/O Ports: 0xd000-0xdfff (rw) Memory Range: 0xfe800000-0xfe83ffff (rw,non-prefetchable) Memory Range: 0xfe840000-0xfe85ffff (ro,non-prefetchable) IRQ: 230 (67 events) Module Alias: "pci:v00001002d000067EFsv00001028sd000007E2bc03sc80i00" Driver Info #0: Driver Status: amdgpu is active Driver Activation Cmd: "modprobe amdgpu" Config Status: cfg=no, avail=yes, need=no, active=unknown Attached to: #22 (PCI bridge) 28: PCI 01.0: 0300 VGA compatible controller (VGA) [Created at pci.378] Unique ID: vSkL.gwUVE8uFOP6 SysFS ID: /devices/pci0000:00/0000:00:01.0 SysFS BusID: 0000:00:01.0 Hardware Class: graphics card Model: "ATI Carrizo" Vendor: pci 0x1002 "ATI Technologies Inc" Device: pci 0x9874 "Carrizo" SubVendor: pci 0x1028 "Dell" SubDevice: pci 0x07e2 Revision: 0xcc Driver: "amdgpu" Driver Modules: "amdgpu" Memory Range: 0xd0000000-0xdfffffff (ro,non-prefetchable) Memory Range: 0xf0800000-0xf0ffffff (ro,non-prefetchable) I/O Ports: 0xf000-0xf0ff (rw) Memory Range: 0xfea00000-0xfea3ffff (rw,non-prefetchable) Memory Range: 0x000c0000-0x000dffff (rw,non-prefetchable,disabled) IRQ: 228 (49683 events) Module Alias: "pci:v00001002d00009874sv00001028sd000007E2bc03sc00i00" Driver Info #0: Driver Status: amdgpu is active Driver Activation Cmd: "modprobe amdgpu" Config Status: cfg=no, avail=yes, need=no, active=unknown Primary display adapter: #28 Here is what my system is using: # lspci -nnk | grep -A3 VGA 00:01.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] Carrizo [1002:9874] (rev cc) Subsystem: Dell Device [1028:07e2] Kernel driver in use: amdgpu Kernel modules: amdgpu I tried to boot without nomodeset, and even though it does get to a point where I can type in my login id, it locks up soon after, whether or not I try to log in. It does not reach the display manager. I was not able to boot up to run level 3, though I only tried it once. Also, it does not create an Xorg.0.log file. Or rather, it creates one, but it is completely empty. I think there may be some compatibility issues within the new kernel and my hardware, perhaps? In any case, how can I get back into my system? Can I even reach runlevel 3 with network compatibility so that I could try and upgrade or downgrade my kernel while running in nomodeset? Do I need to file a bug report? -- George Box: 42.3 | KDE Plasma 5.8 | AMD Phenom IIX4 | 64 | 32GB Laptop #1: TW | Plasma 5.13 | AMD FX 7TH GEN | 64 | 32GB Laptop #2: TW | Plasma 5.13 | Core i5 | 64 | 8GB -- To unsubscribe, e-mail: opensuse-support+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-support+owner@opensuse.org