Kann wer daraus erkennen, warum transcode sofort abbricht: transcode -i /media_out/kino_out/test.dv -V -y mpeg2enc,toolame -o test transcode v0.6.10 (C) 2001-2003 Thomas Oestreich [transcode] auto-probing source /media_out/kino_out/test.dv (ok) [transcode] V: import format | Digital Video (V=dv|A=dv) [transcode] V: import frame | 720x576 1.25:1 encoded @ 4:3 [transcode] V: bits/pixel | 0.174 [transcode] V: decoding fps,frc | 25.000,3 [transcode] V: Y'CbCr | YV12/I420 [transcode] A: import format | 0x1 PCM [48000,16,2] 1536 kbps [transcode] A: export format | 0x55 MPEG layer-3 [48000,16,2] 128 kbps [transcode] V: encoding fps,frc | 25.000,3 [transcode] A: bytes per frame | 7680 (7680.000000) [transcode] A: adjustment | 0@1000 [transcode] V: IA32 accel mode | 3dnow (3dnow mmxext mmx asm) [transcode] V: video buffer | 10 @ 720x576 [import_dv.so] v0.3.0 (2003-05-05) (video) DV | (audio) PCM [export_toolame.so] v1.0.5 (2003-02-06) (audio) MPEG 1/2 [export_mpeg2enc.so] v1.1.9 (2003-08-23) (video) MPEG 1/2 [import_dv.so] tcextract -x dv -i "/media_out/kino_out/test.dv" -d 0 | tcdecode -x dv -y pcm -d 0 [import_dv.so] tcextract -x dv -i "/media_out/kino_out/test.dv" -d 0 | tcdecode -x dv -y yv12 -d 0 -Q 5 [export_mpeg2enc.so] *** init-v *** ! [export_mpeg2enc.so] cmd=mpeg2enc -v 0 -I 0 -q 3 -f 0 -4 2 -2 3 -b 1800 -F 3 -n p -a 2 -o "test".m1v [export_toolame.so] cmd=toolame -s 48.000 -b 128 -m j - "test.mp2" 2>/dev/null encode_init: using tablenum 0 with sblimit 27 clean up | frame threads | unload modules | cancel signal | internal threads | done [transcode] encoded 0 frames (0 dropped, 0 cloned), clip length 0.00 s Eventuell gibt es da ein Problem, das mit transcode nichts zu tun hat. Schreibrechte sollten aber vorhanden sein und als root habe ich die selben Probleme. Die Testdatei läßt sich mit xine problemlos abspielen. Ich habe die Syntax bewußt reduziert um andere Problem auszuschließen. Al -- Infos zu Softwarepatenten: http://swpat.ffii.org/index.de.html http://petition.eurolinux.org/index.html?LANG=de
Am Donnerstag, 25. September 2003 23:30 schrieb Al Bogner:
Kann wer daraus erkennen, warum transcode sofort abbricht:
transcode -i /media_out/kino_out/test.dv -V -y mpeg2enc,toolame -o test
Es scheint wohl immer so zu sein, dass man zuerst lange sucht und dann nach einem Posting einen bedeutenden Schritt weiter ist :-) -V ist der Übeltäter. Aber warum? Aus der Manpage -V use YV12/I420 as internal video codec [off]. This is usually much faster than RGB processing but some import modules may not support this format. Always use this option when possible. Das hat mit früheren Versionen nie Probleme gemacht. Ich verwende das aktuelle Paket von Packman. Al
Am Donnerstag, 25. September 2003 23:48 schrieb Al Bogner:
Am Donnerstag, 25. September 2003 23:30 schrieb Al Bogner:
Kann wer daraus erkennen, warum transcode sofort abbricht:
transcode -i /media_out/kino_out/test.dv -V -y mpeg2enc,toolame -o test
Es scheint wohl immer so zu sein, dass man zuerst lange sucht und dann nach einem Posting einen bedeutenden Schritt weiter ist :-)
-V ist der Übeltäter. Aber warum?
Mit der Option --dv_yuy2_mode funktioniert es nun wieder. Irgendwie habe ich aber den Eindruck, dass die Bildqualität nicht mehr so gut ist wie früher. Artefakte sind deutlich sichtbar. Ich werde da wohl noch mehr testen müssen. Al -- Infos zu Softwarepatenten: http://swpat.ffii.org/index.de.html http://petition.eurolinux.org/index.html?LANG=de
participants (1)
-
Al Bogner