Hallo! Ich weiß nicht, ob ich hier richtig mit meinem Problem bin, aber ich weiß einfach nicht weiter. Ich hab so eine "Pinnacle 300i", mit der man auch DVB-T schauen können sollte. Ging auch mal mit SuSE 9.3 (x86_64). Doch seit dem Aktualisieren auf 10.0 geht nix mehr, auch nicht analoges Fernsehen. Nachdem ich den diversen Hinweisen auf ältere Versionen von v4l gefolgt bin, habe ich auch tatsächlich einmal (und ich weiß nicht, wieso es danach nicht mehr ging) wieder kurz (digitalen, analog hatte ich in der kurzen Zeit nicht ausprobiert) Empfang, und zwar so gut, daß ich nachvollziehen konnte, daß die ältere v4l-Kiste tatsächlich den MPEG-Strom aus dem DVB-T-Signal nicht so gut rauszieht, irgendwas soll da mit der Fehlerkorrektur nicht hinhauen, hab ich irgendwo gelesen. Ist jedenfalls nachvollziehbar, weil ich hier einen erstklassigen Empfang haben müßte (und unter W**doof auch habe). Doch konnte ich den Erfolg nicht reproduzieren, weiß der Bitteufel wieso. Daraufhin habe ich mir den stets aktuellen kotd (und gcc 4.1) besorgt, aber nie Erfolg gehabt. Dazu probiere ich auch immer die alleraktuellste v4l-dvb-Geschichte aus. Also einmal kotd pur, dann + v4l-dvb. Nix. Das heißt, auf /var/log/messages scheint alles zu funktionieren, Karte erkannt, Microtune-Tuner erkannt, alles paletti: -schnipp- Jan 8 11:55:06 linux kernel: tuner: module not supported by Novell, setting U taint flag. Jan 8 11:55:06 linux kernel: tuner 1-0061: chip found @ 0xc2 (bt878 #0 [sw]) Jan 8 11:55:06 linux kernel: tuner 1-0061: type set to 5 (Philips PAL_BG (FI1216 an d compatibles)) Jan 8 11:55:15 linux kernel: saa7134: module not supported by Novell, setting U tai nt flag. Jan 8 11:55:15 linux kernel: saa7130/34: v4l2 driver version 0.2.14 loaded Jan 8 11:55:15 linux kernel: ACPI: PCI Interrupt 0000:05:05.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 233 Jan 8 11:55:15 linux kernel: saa7134[0]: found at 0000:05:05.0, rev: 1, irq: 233, l atency: 32, mmio: 0xc9002000 Jan 8 11:55:15 linux kernel: saa7134[0]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T + PAL [card=50,autodetected] Jan 8 11:55:15 linux kernel: saa7134[0]: board init: gpio is c806000 Jan 8 11:55:15 linux kernel: tda9887 0-0043: chip found @ 0x86 (saa7134[0]) Jan 8 11:55:15 linux kernel: tuner 0-0060: Chip ID is not zero. It is not a TEA5767 Jan 8 11:55:15 linux kernel: tuner 0-0060: chip found @ 0xc0 (saa7134[0]) Jan 8 11:55:15 linux kernel: tuner 0-0060: microtune: companycode=3cbf part=42 rev= 2f Jan 8 11:55:15 linux kernel: tuner 0-0060: microtune MT2050 found, OK Jan 8 11:55:15 linux kernel: saa7134[0]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92 Jan 8 11:55:15 linux kernel: saa7134[0]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff ff ff Jan 8 11:55:15 linux kernel: saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff ff ff Jan 8 11:55:15 linux kernel: saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Jan 8 11:55:15 linux kernel: saa7134[0]: i2c eeprom 40: ff 16 00 c0 86 3c 01 01 ff ff ff ff ff ff ff ff Jan 8 11:55:15 linux kernel: saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Jan 8 11:55:15 linux kernel: saa7134[0]: i2c eeprom 60: 0c 22 17 44 03 01 22 36 ff ff ff ff ff ff ff ff Jan 8 11:55:15 linux kernel: saa7134[0]: i2c eeprom 70: 00 30 8d 16 d5 47 ff ff f4 4c ff ff ff ff ff ff Jan 8 11:55:15 linux kernel: saa7134[0]: registered device video0 [v4l2] Jan 8 11:55:15 linux kernel: saa7134[0]: registered device vbi0 Jan 8 11:55:35 linux kernel: video_buf_dvb: module not supported by Novell, setting U taint flag. Jan 8 11:55:35 linux kernel: mt352: module not supported by Novell, setting U taint flag. Jan 8 11:55:35 linux kernel: saa7134_dvb: module not supported by Novell, setting U taint flag. Jan 8 11:55:35 linux kernel: saa7134[0]: pinnacle 300i dvb setup Jan 8 11:55:35 linux kernel: DVB: registering new adapter (saa7134[0]). Jan 8 11:55:35 linux kernel: DVB: registering frontend 0 (Zarlink MT352 DVB-T)... Jan 8 11:55:43 linux kernel: saa7134[0]: mt352_pinnacle_init called -schnapp- So sah das auch etwa früher aus. Will ich aber mal was sehen, mit kaffeine, z.B., so scheint der irgendwie zu hängen, auf /var/log/messages kam nur dies: -schnipp- Jan 8 11:57:05 linux kernel: saa7134[0]: mt352_pinnacle_init called Jan 8 11:57:36 linux last message repeated 29 times Jan 8 11:58:24 linux last message repeated 45 times -schnapp- Ebenso mit allem anderen. Läuft nix. Gelesen hab ich, daß man die Firmware aktualisieren muß, aber ich dachte, meine sei schon aktuell, weil es mal ging. Wie kriege ich raus, was für 'ne Firmware auf meiner Karte ist, und wie kann ich die aktualisieren. Wo bekomme ich die z.B.. Ich hab von Windows so gut wie keine Ahnung und schon verzweifelt gesucht. Das wäre meine letzte Hoffnung, oder kennt jemand das Problem und dessen Lösung? Hab ich irgendein Modul vergessen? Geladen hab ich tuner, saa7134, saa7134_dvb. Automatisch lädt der dann mt352 hinzu. Das war's dann, glaub ich. Vielen Dank und liebe Grüße Tim
participants (1)
-
Tim Gollnik