Hallo alle, Ich habe immer noch Probleme mit Standby. Mein System: Suse 9.1 kernel 2.6.5-7.75 neuste powersave from ftp://ftp.suse.com/pub/people/seife/powersave/ Nach dem Einschalten und Hochfahren funktioniert alles einwandfrei. Nach Standby und Resume scheint alles wieder zu funktionieren. Dann bricht nach einiger Zeit das Netzwerk zusammen. Dann funktioniert die Tastatur nicht mehr richtig (liegt am ipw2100 Modul: nach rmmod ipw2100 geht Tastatur wieder). rcnetwork restart bringt genausowenig wie rmmod bcm5700, modprobe bcm5700. Komischerweise funktioniert das Netzwerk nach erneutem Standby und Resume wieder bricht allerdings nach einiger Zeit wieder zusammen (kann Minuten bis Stunden dauern). Woran kann das nur liegen? Hier noch Auszug aus /var/log/messages: Jul 1 18:30:45 dennis [powersaved][4311]: DIAG in Function executeEvent, line 1497: Executed event: button.sleep Jul 1 18:30:45 dennis [powersaved][4311]: DIAG in Function executeEvent, line 1497: Executed event: global.standby Jul 1 18:30:46 dennis kernel: ehci_hcd 0000:00:1d.7: remove, state 1 Jul 1 18:30:46 dennis kernel: usb usb1: USB disconnect, address 1 Jul 1 18:30:46 dennis kernel: ehci_hcd 0000:00:1d.7: USB bus 1 deregistered Jul 1 18:30:46 dennis dhcpcd[2235]: recvfrom: Network is down Jul 1 18:30:46 dennis /sbin/hotplug-stopped[0]: hotplugging not enabled. Run rchotplug start Jul 1 18:30:46 dennis last message repeated 2 times Jul 1 18:30:46 dennis dhcpcd[2235]: dhcpStop: ioctl SIOCSIFADDR: No such device Jul 1 18:30:46 dennis [powersave_proxy][5724]: WARNING: Modules unloaded Jul 1 18:30:46 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1592: CPU state changed to high! CPU load: 98 Jul 1 18:30:46 dennis [powersave_proxy][5793]: DIAG: dethrottle cpu Jul 1 18:30:46 dennis [powersaved][4311]: DIAG in Function executeEvent, line 1497: Executed event: processor.dynamic.high Jul 1 18:30:46 dennis dhcpcd[2235]: dhcpStop: ioctl SIOCSIFFLAGS: No such device Jul 1 18:30:46 dennis /sbin/hotplug-stopped[0]: hotplugging not enabled. Run rchotplug start Jul 1 18:30:46 dennis /sbin/hotplug-stopped[0]: hotplugging not enabled. Run rchotplug start Jul 1 18:30:46 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1588: CPU state changed to low! CPU load: 30 Jul 1 18:30:47 dennis modify_resolvconf: no matching backup found, left everything alone Jul 1 18:30:47 dennis dhcpcd-hook: Skipping 'ifdown $INTERFACE -o dhcp' call Jul 1 18:30:47 dennis [powersaved][5723]: DIAG in Function executeEvent, line 1470: SET do standby to 1 Jul 1 18:30:47 dennis kernel: PM: Preparing system for suspend Jul 1 18:31:02 dennis kernel: Stopping tasks: ==============================================================================================| Jul 1 18:31:02 dennis kernel: PM: Entering state. Jul 1 18:31:02 dennis kernel: Back to C! Jul 1 18:31:02 dennis kernel: PM: Finishing up. Jul 1 18:31:02 dennis kernel: PCI: Setting latency timer of device 0000:00:1d.0 to 64 Jul 1 18:31:02 dennis kernel: PCI: Setting latency timer of device 0000:00:1d.1 to 64 Jul 1 18:31:02 dennis kernel: PCI: Setting latency timer of device 0000:00:1d.2 to 64 Jul 1 18:31:02 dennis kernel: PCI: Setting latency timer of device 0000:00:1d.7 to 64 Jul 1 18:31:02 dennis kernel: PCI: Setting latency timer of device 0000:00:1f.5 to 64 Jul 1 18:31:02 dennis kernel: PCI: Setting latency timer of device 0000:00:1f.6 to 64 Jul 1 18:31:02 dennis kernel: PCI: Enabling device 0000:02:01.2 (0000 -> 0002) Jul 1 18:31:02 dennis /sbin/hotplug-stopped[0]: hotplugging not enabled. Run rchotplug start Jul 1 18:31:02 dennis kernel: blk: queue dfc32200, I/O limit 4095Mb (mask 0xffffffff) Jul 1 18:31:02 dennis kernel: Restarting tasks... done Jul 1 18:31:02 dennis [powersaved][4311]: DIAG in Function executeEvent, line 1497: Executed event: global.resume.standby Jul 1 18:31:02 dennis /sbin/hotplug-stopped[0]: hotplugging not enabled. Run rchotplug start Jul 1 18:31:02 dennis kernel: Synaptics Touchpad, model: 1 Jul 1 18:31:02 dennis kernel: Firmware: 4.6 Jul 1 18:31:02 dennis kernel: 180 degree mounted touchpad Jul 1 18:31:02 dennis kernel: Sensor: 18 Jul 1 18:31:02 dennis kernel: new absolute packet format Jul 1 18:31:02 dennis kernel: Touchpad has extended capability bits Jul 1 18:31:02 dennis kernel: -> four buttons Jul 1 18:31:02 dennis kernel: -> multifinger detection Jul 1 18:31:02 dennis kernel: -> palm detection Jul 1 18:31:02 dennis kernel: input: SynPS/2 Synaptics TouchPad on isa0060/serio4 Jul 1 18:31:02 dennis [powersave_proxy][5859]: DIAG: Service hotplug started again Jul 1 18:31:03 dennis /sbin/hotplug-stopped[0]: hotplugging not enabled. Run rchotplug start Jul 1 18:31:03 dennis last message repeated 2 times Jul 1 18:31:03 dennis kernel: bcm5700: unsupported module, tainting kernel. Jul 1 18:31:03 dennis kernel: Broadcom Gigabit Ethernet Driver bcm5700 with Broadcom NIC Extension (NICE) ver. 7.1.22 (01/07/04) Jul 1 18:31:03 dennis kernel: bcm5700-0: TSO not available on this NIC Jul 1 18:31:03 dennis kernel: eth0: Broadcom BCM5788 1000Base-T found at mem ff9f0000, IRQ 4, node addr 000ea6c48ac0 Jul 1 18:31:03 dennis kernel: eth0: Broadcom BCM5705 Integrated Copper transceiver found Jul 1 18:31:03 dennis kernel: eth0: Scatter-gather ON, 64-bit DMA OFF, Tx Checksum ON, Rx Checksum ON, 802.1Q VLAN ON, NAPI ON Jul 1 18:31:03 dennis kernel: ipw2100: unsupported module, tainting kernel. Jul 1 18:31:03 dennis kernel: ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, 0.46_3 Jul 1 18:31:03 dennis kernel: ipw2100: Copyright(c) 2003-2004 Intel Corporation Jul 1 18:31:03 dennis kernel: Detected ipw2100 PCI device at 0000:02:02.0, mem: 0xFF9EE000-0xFF9EEFFF -> e2851000, irq: 4 Jul 1 18:31:03 dennis kernel: eth1: Using hotplug firmware load. Jul 1 18:31:03 dennis /sbin/hotplug-stopped[0]: hotplugging not enabled. Run rchotplug start Jul 1 18:31:03 dennis [powersaved][4311]: DIAG in Function getBatteriesInfo, line 31: remaining: 97 percent, -1 minutes Jul 1 18:31:03 dennis [powersaved][4311]: WARNING in Function start; line 388: Select returned an Error, but not interrupted through a signal: Success! This is not nice, but normal after a suspend! Jul 1 18:31:03 dennis kernel: Registered as eth1 Jul 1 18:31:03 dennis kernel: ehci_hcd 0000:00:1d.7: EHCI Host Controller Jul 1 18:31:03 dennis kernel: PCI: Setting latency timer of device 0000:00:1d.7 to 64 Jul 1 18:31:03 dennis kernel: ehci_hcd 0000:00:1d.7: irq 10, pci mem e293cc00 Jul 1 18:31:03 dennis kernel: ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 Jul 1 18:31:03 dennis kernel: PCI: cache line size of 32 is not supported by device 0000:00:1d.7 Jul 1 18:31:03 dennis kernel: ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29 Jul 1 18:31:03 dennis kernel: usb usb1: Product: EHCI Host Controller Jul 1 18:31:03 dennis kernel: usb usb1: Manufacturer: Linux 2.6.5-7.75-default ehci_hcd Jul 1 18:31:03 dennis kernel: usb usb1: SerialNumber: 0000:00:1d.7 Jul 1 18:31:03 dennis kernel: hub 1-0:1.0: USB hub found Jul 1 18:31:03 dennis kernel: hub 1-0:1.0: 6 ports detected Jul 1 18:31:03 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1592: CPU state changed to high! CPU load: 82 Jul 1 18:31:03 dennis [powersave_proxy][5859]: DIAG: Modules loaded Jul 1 18:31:04 dennis /etc/hotplug/usb.agent[5997]: need a device for this command Jul 1 18:31:04 dennis kernel: ipw2100: eth1: Restarting adapter. Jul 1 18:31:04 dennis kernel: eth1: Using hotplug firmware load. Jul 1 18:31:04 dennis kernel: usb 3-1: USB disconnect, address 2 Jul 1 18:31:04 dennis /etc/hotplug/usb.agent[6175]: need a device for this command Jul 1 18:31:04 dennis kernel: usb 3-1: new low speed USB device using address 3 Jul 1 18:31:05 dennis kernel: usb 3-1: Product: Optical USB Mouse Jul 1 18:31:05 dennis kernel: usb 3-1: Manufacturer: Logitech Jul 1 18:31:05 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1588: CPU state changed to low! CPU load: 34 Jul 1 18:31:05 dennis /etc/hotplug/usb.agent[6264]: need a device for this command Jul 1 18:31:05 dennis kernel: input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.1-1 Jul 1 18:31:05 dennis kernel: usb 2-2: USB disconnect, address 2 Jul 1 18:31:05 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1592: CPU state changed to high! CPU load: 94 Jul 1 18:31:05 dennis /etc/hotplug/usb.agent[6335]: need a device for this command Jul 1 18:31:05 dennis kernel: bcm5700: eth0 NIC Link is UP, 100 Mbps full duplex, receive & transmit flow control ON Jul 1 18:31:05 dennis kernel: usb 2-2: new full speed USB device using address 3 Jul 1 18:31:05 dennis kernel: usb 2-2: Product: Camera Jul 1 18:31:05 dennis kernel: quickcam: QuickCam USB camera found (driver version QuickCam USB $Date: 2003/12/31 16:15:06 $) Jul 1 18:31:05 dennis kernel: quickcam: Kernel:2.6.5-7.75-default bus:2 class:FF subclass:FF vendor:046D product:0870 Jul 1 18:31:05 dennis kernel: quickcam: Sensor HDCS-1020 detected Jul 1 18:31:05 dennis /etc/hotplug/usb.agent[6396]: need a device for this command Jul 1 18:31:05 dennis kernel: quickcam: Registered device: /dev/video0 Jul 1 18:31:05 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1588: CPU state changed to low! CPU load: 57 Jul 1 18:31:09 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1592: CPU state changed to high! CPU load: 81 Jul 1 18:31:12 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1588: CPU state changed to low! CPU load: 9 Jul 1 18:31:14 dennis kernel: eth0: no IPv6 routers present Jul 1 18:31:14 dennis kernel: eth1: no IPv6 routers present Jul 1 18:31:19 dennis [powersaved][4311]: DIAG in Function executeEvent, line 1497: Executed event: processor.dynamic.low Jul 1 18:31:54 dennis [powersaved][4311]: DIAG in Function getBatteriesInfo, line 31: remaining: 97 percent, -1 minutes Jul 1 18:32:08 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1592: CPU state changed to high! CPU load: 100 Jul 1 18:32:08 dennis [powersave_proxy][6659]: DIAG: dethrottle cpu Jul 1 18:32:08 dennis [powersaved][4311]: DIAG in Function executeEvent, line 1497: Executed event: processor.dynamic.high Jul 1 18:32:10 dennis acpi_hotkeys: non-hotkey-event: other thermal_zone THRM 00000081 00000000 Jul 1 18:32:10 dennis [powersaved][4311]: DIAG in Function executeEvent, line 1497: Executed event: other Jul 1 18:32:11 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1588: CPU state changed to low! CPU load: 30 Jul 1 18:32:12 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1592: CPU state changed to high! CPU load: 100 Jul 1 18:32:13 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1588: CPU state changed to low! CPU load: 0 Jul 1 18:32:23 dennis [powersaved][4311]: DIAG in Function executeEvent, line 1497: Executed event: processor.dynamic.low Jul 1 18:32:41 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1592: CPU state changed to high! CPU load: 100 Jul 1 18:32:41 dennis [powersave_proxy][6688]: DIAG: dethrottle cpu Jul 1 18:32:41 dennis [powersaved][4311]: DIAG in Function executeEvent, line 1497: Executed event: processor.dynamic.high Jul 1 18:32:42 dennis [powersaved][4311]: DIAG in Function updateCPUState, line 1588: CPU state changed to low! CPU load: 0 Jul 1 18:32:52 dennis [powersaved][4311]: DIAG in Function executeEvent, line 1497: Executed event: processor.dynamic.low Jul 1 18:32:55 dennis [powersaved][4311]: DIAG in Function getBatteriesInfo, line 31: remaining: 97 percent, -1 minutes Jul 1 18:33:01 dennis kernel: eth1: Firmware RTC stalled. Jul 1 18:33:01 dennis kernel: eth1: Scheduling firmware restart. Jul 1 18:33:01 dennis kernel: ipw2100: eth1: Restarting adapter. Jul 1 18:33:01 dennis kernel: eth1: Using hotplug firmware load. Jul 1 18:33:04 dennis kernel: eth1: ipw2100_hw_send_command timed out. Jul 1 18:33:04 dennis kernel: eth1: Failed to start the card. Jul 1 18:33:05 dennis kernel: eth1: Hardware fatal error detected. Jul 1 18:33:05 dennis kernel: eth1: Scheduling firmware restart. Jul 1 18:33:05 dennis kernel: ipw2100: eth1: Restarting adapter. Jul 1 18:33:05 dennis kernel: eth1: Using hotplug firmware load. Jul 1 18:33:08 dennis kernel: eth1: ipw2100_hw_send_command timed out. Jul 1 18:33:08 dennis kernel: eth1: Failed to start the card. Jul 1 18:33:09 dennis kernel: eth1: Hardware fatal error detected. ________________________________________________________________ Verschicken Sie romantische, coole und witzige Bilder per SMS! Jetzt neu bei WEB.DE FreeMail: http://freemail.web.de/?mc=021193