Re: WLAN will nicht mehr
Moin From: "Thilo A. Coblenzer" Sunday, March 24, 2002 9:44 AM
Tja nur jetzt schaffe ich es einfach nicht mehr meine Intel-WLAN-Karte einzurichten - also vorher gings. Ich verwende das interne PCMCIA. Dazu habe ich in der rc.config START_PCMCIA="yes" und PCMCIA="yenta_socket" stehen. In der pcmcia.rc.config steht bei mir PCMCIA_SYSTEM="kernel" und PCMCIA_PCIC="yenta_socket". Dann habe ich per Yast die Netzwerkkarte als eth0 mit 192.168.0.3 und Gateway eingerichtet. PCMCIA eingeschaltet und die Karte altiviert. Unter neue Hardware hinzufügen habe ich eth0 als PCMCIA angemeldet (das ist doch unnötg, oder?).
Wenn ich die Karte starten will, steht folgendes in der /var/log/messages: cardmgr[224]: initializing socket 0 cardmgr[224]: socket 0: Intel PRO/Wireless 2011 cardmgr[224]: executing: 'insmod -v /lib/modules/2.4.10-4GB//pcmcia/hermes.o' cardmgr[224]: + Using /lib/modules/2.4.10-4GB//pcmcia/hermes.o cardmgr[224]: + Symbol version prefix '' kernel: hermes.c: 1 Aug 2001 David Gibson
cardmgr[224]: executing: 'insmod -v/lib/modules/2.4.10-4GB//pcmcia/orinoco.o' cardmgr[224]: + Using /lib/modules/2.4.10-4GB//pcmcia/orinoco.o cardmgr[224]: + Symbol version prefix '' kernel: orinoco.c 0.07 (David Gibson and others) cardmgr[224]: executing: 'insmod -v /lib/modules/2.4.10-4GB//pcmcia/orinoco_cs.o' cardmgr[224]: + Using /lib/modules/2.4.10-4GB//pcmcia/orinoco_cs.o cardmgr[224]: + Symbol version prefix '' kernel: orinoco_cs.c 0.07 (David Gibson and others) kernel: eth0: Station identity 001f:0002:0002:0001 kernel: eth0: Looks like a Symbol firmware (unknown version) kernel: eth0: Ad-hoc demo mode supported. kernel: eth0: IEEE standard IBSS ad-hoc mode supported. kernel: eth0: WEP supported, "128"-bit key. kernel: eth0: MAC address 00:02:B3:06:3C:68 kernel: eth0: Station name "Prism I" kernel: eth0: ready kernel: eth0: index 0x01: Vcc 5.0, irq 3, io 0x0100-0x0147 cardmgr[224]: executing: './network start eth0' cardmgr[224]: + /sbin/route add -net 192.168.0.0 netmask 255.255.255.0 dev eth0 cardmgr[224]: + SIOCADDRT: Network is down cardmgr[224]: + SIOCADDRT: Network is unreachable modify_resolvconf: Service pcmcia modified /etc/resolv.conf. See info block in this file Danach liefert iwconfig eth0 folgendes: eth0 IEEE 802.11-DS Nickname:"Prism I" Mode:Managed Frequency:42.9497GHz Tx-Power=15 dBm RTS thr:off Encryption key:off
Verschlüsselung ist nicht aktiviert und ein iwconfig eth0 essid XXXX hilft auch nix! Dann habe ich mal folgendes probiert: ifconfig eth0 192.168.0.3 braodcast 192.168.0.255 netmask 255.255.255.0 up braodcast: Host name lookup failure
Und zu guter letzt kann ich Euch nur noch die Ausgabe von cardctl ident geben, die mir sagt. daß die Karte richtig erkannt wird. Socket 0: product info: "Intel", "PRO/Wireless 2011 LAN PC Card", "1.00" manfid: 0x0089, 0x0001 function: 6 (network)
Was mich noch etwas verwirrt, jetzt steht in /var/log/messages 128-Bit-Verschlüssellung wird unterstützt - laut Handbuch ist das auch so, allerdings stand da früher 40 Bit.
Ich habe noch etwas gefunden. Vielleicht kann damit ja jemand etwas anfangen
oder hat einen Tip für mich. Und zwar ist es die Ausgabe dmesg:
hermes.c: 1 Aug 2001 David Gibson
participants (1)
-
Thilo A. Coblenzer