![](https://seccdn.libravatar.org/avatar/cade75bc5a38eae7b8d86692a7433a68.jpg?s=120&d=mm&r=g)
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 On Monday 08 December 2003 00:50, Tim Oliver Wagner wrote:
Connecting to /dev/ircomm0, speed 9600. The escape character is Ctrl-\ (ASCII 28, FS) Type the escape character followed by C to get back, or followed by ? to see other options. - ----------------------------------------------------
leider kommt ab hier gar nix mehr. Selbst CTRL-C funktioniert nicht. :-(
Du musst richtig lesen, was der Computer Dir sagt. Das hilft oft.
The escape character is Ctrl-\ (ASCII 28, FS) Type the escape character followed by C to get back, or followed by ? to see other options.
Du musst also CTRL-Backslash gefolgt von C eingeben, um aus dem mit der Device verbundenen Modus wieder in den mit dem Prompt zu wechseln. CTRL-\ gefolgt von einem Fragezeichen liefert eine kurze Hilfe, was sonst noch so alles nach dem CTRL-\ eingegeben werden kann: Press: C to return to opi ? or H for this message 0 (zero) to send the NUL (0) character B to send a BREAK signal (0.275sec) L to send a Long BREAK (1.5sec) U to hangup and close the connection Q to hangup and quit Kermit S for status ! to push to local shell Z to suspend \ backslash code: \nnn decimal character code \Onnn octal character code \Xhh hexadecimal character code; terminate with Carriage Return. Type the escape character again to send the escape character itself, or press the space-bar to resume the CONNECT session. Press a key>
Ansonsten sieht es genau gleich aus! (ich konnte jedoch nicht finden, wozu ich SET CARRIER-WATCH OFF eingeben muss ...)
Kommt dies bei Euch vor, wenn nix vor dem IR liegt - oder deutet es darauf hin, dass mein IR nicht installiert ist.
Ich denke, es liegt daran, dass Dein IR nicht funtioniert. Gib mal rcirda start ein, bevor Du kermit startest. Danach sollten folgende Module geladen sein: irtty 8928 2 (autoclean) ircomm-tty 36160 0 (autoclean) ircomm 16808 0 (autoclean) [ircomm-tty] irda 172816 1 (autoclean) [irtty ircomm-tty ircomm] Prüfe das mit 'lsmod'! Außerdem läuft dann ein 'irattach' Prozess: 8965 ? S 0:00 /usr/sbin/irattach /dev/ttyS1 -s Prüfe es mit 'ps ax'! Ich denke, danach sollte es funktionieren. Falls Du oft mit dem Handy ins Internet willst, kannst Du irda automatisch starten. Entweder mit yast2 ==> System ==> Runlevel editor, oder einfach per Hand einen logischen Link in /etc/init.d/rc?.d erzeugen, der auf /etc/init.d/irda zeigt. ? ist dabei Dein übliches Runlevel (einfach zu ermitteln mit dem Befehl 'runlevel'). So, hoffentlich hilft's, Torsten -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.0.7 (GNU/Linux) iD8DBQE/1EEiwicyCTir8T4RAuyMAJ4p0OXuZQ8pNiVJU+hno4ektJi22gCfbXjJ FujvdIBYmZi/eI/j5KcwXnM= =n//X -----END PGP SIGNATURE-----