Hi, Greg, Unfortunately it's my laptop... And here's smartctl information: smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.11.10-11-desktop] (SUSE RPM) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M8 (AF) Device Model: SAMSUNG HN-M101MBB Serial Number: S2R8J9BB808817 LU WWN Device Id: 5 0024e9 205e8f61c Firmware Version: 2AR10001 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 3.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jul 22 02:09:58 2014 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13320) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 222) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 2850 2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0 3 Spin_Up_Time 0x0023 089 089 025 Pre-fail Always - 3466 4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2161 5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0 8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 12867 10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 135 12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 2242 181 Program_Fail_Cnt_Total 0x0022 080 080 000 Old_age Always - 452013413 191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 820 192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0 194 Temperature_Celsius 0x0002 064 047 000 Old_age Always - 36 (Min/Max 17/53) 195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0 196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 252 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 463 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 135 225 Load_Cycle_Count 0x0032 032 032 000 Old_age Always - 691031 SMART Error Log Version: 1 Warning: ATA error count 19579 inconsistent with error log pointer 5 ATA Error Count: 19579 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 19579 occurred at disk power-on lifetime: 12857 hours (535 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 84 ef 8f e3 Error: UNC 8 sectors at LBA = 0x038fef84 = 59764612 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 84 ef 8f e3 00 00:00:00.203 READ DMA ef 10 02 00 00 00 a0 00 00:00:00.203 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 00:00:00.203 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 00:00:00.203 IDENTIFY DEVICE ef 02 00 00 00 00 a0 00 00:00:00.203 SET FEATURES [Enable write cache] Error 19578 occurred at disk power-on lifetime: 12725 hours (530 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 84 ef 8f e3 Error: UNC 8 sectors at LBA = 0x038fef84 = 59764612 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 84 ef 8f e3 00 00:00:00.233 READ DMA c8 00 08 84 ef 93 e0 00 00:00:00.233 READ DMA c8 00 08 ac ef 93 e0 00 00:00:00.233 READ DMA c8 00 08 cc ef 93 e0 00 00:00:00.233 READ DMA c8 00 08 44 fa 93 e0 00 00:00:00.233 READ DMA Error 19577 occurred at disk power-on lifetime: 12680 hours (528 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 84 ef 8f e3 Error: UNC 8 sectors at LBA = 0x038fef84 = 59764612 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 84 ef 8f e3 00 00:00:35.602 READ DMA 25 00 10 15 ed 7a e0 00 00:00:35.602 READ DMA EXT 25 00 10 f5 9c 76 e0 00 00:00:35.602 READ DMA EXT 25 00 10 05 c7 7a e0 00 00:00:35.602 READ DMA EXT 25 00 10 f5 99 76 e0 00 00:00:35.602 READ DMA EXT Error 19576 occurred at disk power-on lifetime: 12678 hours (528 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 84 ef 8f e3 Error: UNC 8 sectors at LBA = 0x038fef84 = 59764612 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 84 ef 8f e3 00 00:00:29.969 READ DMA c8 00 50 d4 d9 6f e0 00 00:00:29.969 READ DMA c8 00 30 3c e0 6f e0 00 00:00:29.969 READ DMA c8 00 88 b4 df 6f e0 00 00:00:29.969 READ DMA c8 00 e8 14 d7 6f e0 00 00:00:29.969 READ DMA Error 19575 occurred at disk power-on lifetime: 12678 hours (528 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 c8 84 ef 8f e3 Error: UNC 200 sectors at LBA = 0x038fef84 = 59764612 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 f8 54 ef 8f e3 00 00:00:29.968 READ DMA c8 00 08 4c ef 8f e3 00 00:00:29.968 READ DMA c8 00 08 44 ef 8f e3 00 00:00:29.968 READ DMA c8 00 20 44 ca 6f e0 00 00:00:29.968 READ DMA c8 00 b0 b4 be ac e3 00 00:00:29.968 READ DMA SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. I at first didn't treat it as a hardware problem, I treated it as a software problem because I can't believe all in a sudden my disk was producting "end_request" for about 10 sectors in a very narrow time window (in just a few minutes..) while I can still use my openSUSE without any major problem (the hard shutdown will result a slow boot, the suspend to ram/disk function still looks fine, and the daily operation is good too) Marguerite On Tue, Jul 22, 2014 at 1:48 AM, Greg Freemyer <greg.freemyer@gmail.com> wrote:
On Mon, Jul 21, 2014 at 12:02 PM, Larry Finger <Larry.Finger@lwfinger.net> wrote:
If this system is a desktop, an easy thing to do is to replace the cable. On a laptop, that is generally not possible. In any case, I would be sure to have backups and a spare drive.
I agree with Larry in that my first diagnostic step when I see errors being reported is to replace the sata cable. It that fixes the problem, just toss the old cable.
If it doesn't is when I start diving into the "smartctl -a" data.
Greg -- Greg Freemyer -- To unsubscribe, e-mail: opensuse-kernel+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-kernel+owner@opensuse.org
-- To unsubscribe, e-mail: opensuse-kernel+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-kernel+owner@opensuse.org