Hi all, I'm now using a new device usb3 ready. But hot-pluging it drive you nowhere dmesg full of xhci_hcd 0000:04:00.0: WARN: Stalled endpoint hardware reference : see http://www.smolts.org/client/show/pub_f42e5aaf-dce8-4423-a4c6-5a304d36dbc7 dmesg extract [703277.432552] usb 8-2: new SuperSpeed USB device using xhci_hcd and address 2 [703277.452250] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [703277.453121] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [703277.453876] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [703277.454754] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [703277.454915] usb 8-2: New USB device found, idVendor=1759, idProduct=5002 [703277.454923] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [703277.454929] usb 8-2: Product: MassStorage Device [703277.454933] usb 8-2: Manufacturer: USB 3.0 [703277.454936] usb 8-2: SerialNumber: WD-WMAZ20161452 [703277.733066] Initializing USB Mass Storage driver... [703277.733493] scsi13 : usb-storage 8-2:1.0 [703277.733654] usbcore: registered new interface driver usb-storage [703277.733655] USB Mass Storage support registered. [703278.733479] scsi 13:0:0:0: Direct-Access USB 3.0 MassStorage 0100 PQ: 0 ANSI: 4 [703278.733659] sd 13:0:0:0: Attached scsi generic sg18 type 0 [703278.735622] sd 13:0:0:0: [sdj] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [703278.736275] xhci_hcd 0000:04:00.0: WARN: Stalled endpoint [703278.736957] sd 13:0:0:0: [sdj] Write Protect is off [703278.736965] sd 13:0:0:0: [sdj] Mode Sense: 03 00 00 00 [703278.736970] sd 13:0:0:0: [sdj] Assuming drive cache: write through [703278.738513] xhci_hcd 0000:04:00.0: WARN: Stalled endpoint [703278.739234] sd 13:0:0:0: [sdj] Assuming drive cache: write through [703278.739249] sdj: unknown partition table [703278.862035] xhci_hcd 0000:04:00.0: WARN: Stalled endpoint [703278.862603] sd 13:0:0:0: [sdj] Assuming drive cache: write through [703278.862611] sd 13:0:0:0: [sdj] Attached SCSI disk [703867.108949] usb 8-2: USB disconnect, address 2 [703884.744549] usb 8-2: new SuperSpeed USB device using xhci_hcd and address 2 [703884.763176] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [703884.764063] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [703884.764810] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [703884.765704] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [703884.765858] usb 8-2: New USB device found, idVendor=1759, idProduct=5002 [703884.765861] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [703884.765864] usb 8-2: Product: MassStorage Device [703884.765866] usb 8-2: Manufacturer: USB 3.0 [703884.765868] usb 8-2: SerialNumber: WD-WMAZ20161452 [703884.768018] scsi14 : usb-storage 8-2:1.0 [703885.769261] scsi 14:0:0:0: Direct-Access USB 3.0 MassStorage 0100 PQ: 0 ANSI: 4 [703885.769392] sd 14:0:0:0: Attached scsi generic sg18 type 0 [703885.770484] sd 14:0:0:0: [sdk] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [703885.771023] xhci_hcd 0000:04:00.0: WARN: Stalled endpoint [703885.771915] sd 14:0:0:0: [sdk] Write Protect is off [703885.771915] sd 14:0:0:0: [sdk] Mode Sense: 03 00 00 00 [703885.771915] sd 14:0:0:0: [sdk] Assuming drive cache: write through [703885.773913] xhci_hcd 0000:04:00.0: WARN: Stalled endpoint [703885.774582] sd 14:0:0:0: [sdk] Assuming drive cache: write through [703885.774597] sdk: sdk1 [703885.802118] xhci_hcd 0000:04:00.0: WARN: Stalled endpoint [703885.802773] sd 14:0:0:0: [sdk] Assuming drive cache: write through [703885.802782] sd 14:0:0:0: [sdk] Attached SCSI disk Anybody have an idea ? Linux walt 2.6.34-12-default #1 SMP 2010-06-29 02:39:08 +0200 x86_64 x86_64 x86_64 GNU/Linux -- Bruno Friedmann bruno@ioda-net.ch Ioda-Net Sàrl www.ioda-net.ch openSUSE Member User www.ioda.net/r/osu Blog www.ioda.net/r/blog fsfe fellowship www.fsfe.org (bruno.friedmann (at) fsfe.org ) tigerfoot on irc GPG KEY : D5C9B751C4653227 -- To unsubscribe, e-mail: opensuse-kernel+unsubscribe@opensuse.org For additional commands, e-mail: opensuse-kernel+help@opensuse.org