Hatte eine Installation von Hylafax mit Sedlbauer Fax+ PCI unter SuSE 7.0, die tadellos lief. Jetzt hab ich auf SuSE 8.1 umgestellt (Neuinstallation). Alle anderen Serverdienste habe ich auf Anhieb wieder zum Laufen bekommen (inklusive vbox) und auch das Senden von Faxen mit Hylafax geht, nur beim Empfang bricht das Teil immer an der selben Stelle ab. Auf der Seite von Sedlbauer gibts zwar einen Kernelpatch, der ist aber fuer Kernel 2.4.18 (SuSE 8.0) und ich weiss auch nicht, ob das was bringt. Ich hatte eigentlich gehofft, der neue Kernel waere entsprechend verbessert. Hier ist mal ein typisches Logfile aufgelistet (hab nur meine Nummer geixt): Dec 26 17:55:34.86: [ 4956]: SESSION BEGIN 00000018 xxx Dec 26 17:55:34.86: [ 4956]: HylaFAX (tm) Version 4.1.3 Dec 26 17:55:34.86: [ 4956]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled Dec 26 17:55:34.86: [ 4956]: <-- [4:ATA\r] Dec 26 17:55:40.07: [ 4956]: --> [7:CONNECT] Dec 26 17:55:40.07: [ 4956]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyI0' Dec 26 17:55:40.07: [ 4956]: MODEM input buffering enabled Dec 26 17:55:40.07: [ 4956]: RECV FAX: begin Dec 26 17:55:40.07: [ 4956]: RECV FAX: CDPN=20 Dec 26 17:55:40.07: [ 4956]: MODEM input buffering disabled Dec 26 17:55:40.07: [ 4956]: <-- data [23] Dec 26 17:55:40.07: [ 4956]: <-- data [2] Dec 26 17:55:40.09: [ 4956]: --> [7:CONNECT] Dec 26 17:55:40.09: [ 4956]: <-- data [10] Dec 26 17:55:40.09: [ 4956]: <-- data [2] Dec 26 17:55:41.21: [ 4956]: --> [2:OK] Dec 26 17:55:41.21: [ 4956]: <-- [9:AT+FRH=3D3\r] Dec 26 17:55:41.55: [ 4956]: --> [7:CONNECT] Dec 26 17:55:43.04: [ 4956]: --> [2:OK] Dec 26 17:55:43.04: [ 4956]: REMOTE TSI "6913305099931" Dec 26 17:55:43.04: [ 4956]: <-- [9:AT+FRH=3D3\r] Dec 26 17:55:43.05: [ 4956]: --> [7:CONNECT] Dec 26 17:55:43.29: [ 4956]: --> [2:OK] Dec 26 17:55:43.29: [ 4956]: REMOTE wants 14400 bit/s Dec 26 17:55:43.29: [ 4956]: REMOTE wants page width 1728 pixels in 215 mm Dec 26 17:55:43.29: [ 4956]: REMOTE wants A4 page length (297 mm) Dec 26 17:55:43.29: [ 4956]: REMOTE wants 7.7 line/mm Dec 26 17:55:43.29: [ 4956]: REMOTE wants 2-D MR Dec 26 17:55:43.29: [ 4956]: RECV training at v.17 14400 bit/s Dec 26 17:55:43.29: [ 4956]: MODEM set XON/XOFF/DRAIN: input ignored, output generated Dec 26 17:55:43.29: [ 4956]: <-- [11:AT+FRM=3D145\r] Dec 26 17:55:45.04: [ 4956]: --> [7:CONNECT] Dec 26 17:55:46.66: [ 4956]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled Dec 26 17:55:46.66: [ 4956]: RECV: TCF 2913 bytes, 6% non-zero, 2699 zero-run Dec 26 17:55:46.66: [ 4956]: --> [10:NO CARRIER] Dec 26 17:55:46.66: [ 4956]: DELAY 75 ms Dec 26 17:55:46.74: [ 4956]: TRAINING succeeded Dec 26 17:55:46.74: [ 4956]: <-- [9:AT+FTH=3D3\r] Dec 26 17:55:48.37: [ 4956]: --> [7:CONNECT] Dec 26 17:55:48.37: [ 4956]: <-- data [3] Dec 26 17:55:48.37: [ 4956]: <-- data [2] Dec 26 17:55:48.63: [ 4956]: --> [2:OK] Dec 26 17:55:48.63: [ 4956]: MODEM input buffering enabled Dec 26 17:55:48.63: [ 4956]: MODEM set XON/XOFF/FLUSH: input ignored, output generated Dec 26 17:55:48.63: [ 4956]: <-- [11:AT+FRM=3D146\r] Dec 26 17:55:49.29: [ 4956]: --> [7:CONNECT] Dec 26 17:55:49.29: [ 4956]: RECV: begin page Dec 26 17:56:00.79: [ 4956]: RECV: 2300 total lines, 0 bad lines, 0 consecutive bad lines Dec 26 17:56:00.79: [ 4956]: RECV: end page Dec 26 17:56:00.79: [ 4956]: --> [10:NO CARRIER] Dec 26 17:56:00.79: [ 4956]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled Dec 26 17:56:00.79: [ 4956]: MODEM input buffering disabled Dec 26 17:56:00.79: [ 4956]: <-- [9:AT+FRH=3D3\r] Dec 26 17:56:00.95: [ 4956]: --> [7:CONNECT] Dec 26 17:56:01.92: [ 4956]: --> [2:OK] Dec 26 17:56:01.92: [ 4956]: RECV recv EOP (no more pages or documents) Dec 26 17:56:01.92: [ 4956]: <-- [9:AT+FRS=3D7\r] Dec 26 17:56:01.93: [ 4956]: --> [5:ERROR] Dec 26 17:56:01.93: [ 4956]: MODEM Command error Dec 26 17:56:01.93: [ 4956]: RECV FAX (00000018): recvq/fax00012.tif from 6913305099931, route to <unspecified>, 0 pages in 0:21 Dec 26 17:56:01.93: [ 4956]: RECV FAX: Failure to receive silence. Dec 26 17:56:01.93: [ 4956]: <-- [9:AT+FTH=3D3\r] Dec 26 17:56:03.64: [ 4956]: --> [7:CONNECT] Dec 26 17:56:03.64: [ 4956]: <-- data [3] Dec 26 17:56:03.64: [ 4956]: <-- data [2] Dec 26 17:56:03.90: [ 4956]: --> [2:OK] Dec 26 17:56:03.90: [ 4956]: MODEM input buffering enabled Dec 26 17:56:03.90: [ 4956]: RECV FAX (00000018): session with 6913305099931 terminated abnormally: Failure to receive silence. Dec 26 17:56:03.90: [ 4956]: RECV FAX: bin/faxrcvd "recvq/fax00012.tif" "ttyI0" "00000018" "Failure to receive silence." "CALLER NUMBER: 6913303" "CALLER NUMBER: 6913303" "" Dec 26 17:56:04.30: [ 4956]: RECV FAX: end Dec 26 17:56:04.30: [ 4956]: SESSION END Es waere sehr schoen, wenn mir jemand einen Tip geben koennte. Vielen Dank im Voraus. Uwe