Hylafax und mehrseitiger Faxempfang mit Sedlbauer Speed Fax
Hallo Leute, Ich habe hier ein kleines Problem mit dem Empfang mehrseitiger Fax mit Hylafax. Konfiguration: SuSE 7.2, Kernel 2.4.18-xfs, Hylafax 4.1, Sedlbauer Speedfax Pci. Die erste Seite des Faxes kommt sauber an, weitere jedoch nicht. Den entsprechenden Logfile habe ich angehaengt. Danke fuer eure Hilfe. Gruss Marco Zwillich May 10 09:26:45.85: [ 556]: SESSION BEGIN 00000041 49540685005 May 10 09:26:45.85: [ 556]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled May 10 09:26:45.85: [ 556]: <-- [4:ATA\r] May 10 09:26:51.14: [ 556]: --> [7:CONNECT] May 10 09:26:51.14: [ 556]: ANSWER: FAX CONNECTION May 10 09:26:51.14: [ 556]: MODEM input buffering enabled May 10 09:26:51.14: [ 556]: RECV FAX: begin May 10 09:26:51.14: [ 556]: RECV FAX: CDPN May 10 09:26:51.14: [ 556]: MODEM input buffering disabled May 10 09:26:51.14: [ 556]: <-- data [23] May 10 09:26:51.14: [ 556]: <-- data [2] May 10 09:26:51.17: [ 556]: --> [7:CONNECT] May 10 09:26:51.17: [ 556]: <-- data [10] May 10 09:26:51.17: [ 556]: <-- data [2] May 10 09:26:52.28: [ 556]: --> [2:OK] May 10 09:26:52.28: [ 556]: <-- [9:AT+FRH=3\r] May 10 09:26:52.73: [ 556]: --> [7:CONNECT] May 10 09:26:54.33: [ 556]: --> [2:OK] May 10 09:26:54.33: [ 556]: REMOTE TSI "+49 5223 63406" May 10 09:26:54.33: [ 556]: <-- [9:AT+FRH=3\r] May 10 09:26:54.34: [ 556]: --> [7:CONNECT] May 10 09:26:54.61: [ 556]: --> [2:OK] May 10 09:26:54.61: [ 556]: REMOTE wants 14400 bit/s May 10 09:26:54.61: [ 556]: REMOTE wants page width 1728 pixels in 215 mm May 10 09:26:54.61: [ 556]: REMOTE wants unlimited page length May 10 09:26:54.61: [ 556]: REMOTE wants 3.85 line/mm May 10 09:26:54.61: [ 556]: REMOTE wants 2-D MR May 10 09:26:54.61: [ 556]: RECV training at v.17 14400 bit/s May 10 09:26:54.61: [ 556]: MODEM set XON/XOFF/DRAIN: input ignored, output generated May 10 09:26:54.61: [ 556]: <-- [11:AT+FRM=145\r] May 10 09:26:56.33: [ 556]: --> [7:CONNECT] May 10 09:26:57.97: [ 556]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled May 10 09:26:57.97: [ 556]: RECV: TCF 2945 bytes, 4% non-zero, 2767 zero-run May 10 09:26:57.97: [ 556]: --> [10:NO CARRIER] May 10 09:26:57.97: [ 556]: DELAY 75 ms May 10 09:26:58.05: [ 556]: <-- [9:AT+FTH=3\r] May 10 09:26:59.68: [ 556]: --> [7:CONNECT] May 10 09:26:59.68: [ 556]: <-- data [3] May 10 09:26:59.68: [ 556]: <-- data [2] May 10 09:26:59.94: [ 556]: --> [2:OK] May 10 09:26:59.94: [ 556]: TRAINING succeeded May 10 09:26:59.94: [ 556]: MODEM input buffering enabled May 10 09:26:59.94: [ 556]: MODEM set XON/XOFF/FLUSH: input ignored, output generated May 10 09:26:59.94: [ 556]: <-- [11:AT+FRM=146\r] May 10 09:27:01.04: [ 556]: --> [7:CONNECT] May 10 09:27:01.04: [ 556]: RECV: begin page May 10 09:27:28.12: [ 556]: RECV: 1124 total lines, 0 bad lines, 1 consecutive bad lines May 10 09:27:28.12: [ 556]: RECV: end page May 10 09:27:28.12: [ 556]: --> [10:NO CARRIER] May 10 09:27:28.12: [ 556]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled May 10 09:27:28.12: [ 556]: MODEM input buffering disabled May 10 09:27:28.12: [ 556]: <-- [9:AT+FRH=3\r] May 10 09:27:28.16: [ 556]: --> [7:CONNECT] May 10 09:27:29.23: [ 556]: --> [2:OK] May 10 09:27:29.23: [ 556]: RECV recv MPS (more pages, same document) May 10 09:27:29.23: [ 556]: DELAY 150 ms May 10 09:27:29.38: [ 556]: <-- [9:AT+FTH=3\r] May 10 09:27:29.38: [ 556]: --> [10:NO CARRIER] May 10 09:27:29.38: [ 556]: RECV send MCF (message confirmation) May 10 09:27:29.38: [ 556]: RECV FAX (00000041): from +49 5223 63406, page 1 in 0:30, INF, 3.85 line/mm, 2-D MR, 14400 b May 10 09:27:29.38: [ 556]: MODEM input buffering enabled May 10 09:27:29.38: [ 556]: MODEM set XON/XOFF/FLUSH: input ignored, output generated May 10 09:27:29.38: [ 556]: <-- [11:AT+FRM=146\r] May 10 09:27:32.69: [ 556]: --> [7:CONNECT] May 10 09:27:32.69: [ 556]: RECV: begin page May 10 09:27:32.69: [ 556]: RECV: 0 total lines, 0 bad lines, 0 consecutive bad lines May 10 09:27:32.69: [ 556]: RECV: end page May 10 09:27:32.69: [ 556]: --> [10:NO CARRIER] May 10 09:27:32.69: [ 556]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled May 10 09:27:32.69: [ 556]: MODEM input buffering disabled May 10 09:27:32.69: [ 556]: <-- [9:AT+FRH=3\r] May 10 09:27:32.72: [ 556]: --> [7:CONNECT] May 10 09:27:33.55: [ 556]: --> [2:OK] May 10 09:27:33.55: [ 556]: RECV recv MPS (more pages, same document) May 10 09:27:33.55: [ 556]: DELAY 150 ms May 10 09:27:33.70: [ 556]: <-- [9:AT+FTH=3\r] May 10 09:27:33.70: [ 556]: --> [10:NO CARRIER] May 10 09:27:33.70: [ 556]: RECV send MCF (message confirmation) May 10 09:27:33.70: [ 556]: RECV FAX (00000041): from +49 5223 63406, page 2 in 0:04, INF, 3.85 line/mm, 2-D MR, 14400 b May 10 09:27:33.70: [ 556]: MODEM input buffering enabled May 10 09:27:33.70: [ 556]: MODEM set XON/XOFF/FLUSH: input ignored, output generated May 10 09:27:33.70: [ 556]: <-- [11:AT+FRM=146\r] May 10 09:27:37.02: [ 556]: --> [7:CONNECT] May 10 09:27:37.02: [ 556]: RECV: begin page May 10 09:27:37.02: [ 556]: RECV: 0 total lines, 0 bad lines, 0 consecutive bad lines May 10 09:27:37.02: [ 556]: RECV: end page May 10 09:27:37.02: [ 556]: --> [10:NO CARRIER] May 10 09:27:37.02: [ 556]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled May 10 09:27:37.02: [ 556]: MODEM input buffering disabled May 10 09:27:37.02: [ 556]: <-- [9:AT+FRH=3\r] May 10 09:27:37.05: [ 556]: --> [7:CONNECT] May 10 09:27:37.88: [ 556]: --> [2:OK] May 10 09:27:37.88: [ 556]: RECV recv MPS (more pages, same document) May 10 09:27:37.88: [ 556]: DELAY 150 ms May 10 09:27:38.03: [ 556]: <-- [9:AT+FTH=3\r] May 10 09:27:38.03: [ 556]: --> [10:NO CARRIER] May 10 09:27:38.03: [ 556]: RECV send MCF (message confirmation) May 10 09:27:38.03: [ 556]: RECV FAX (00000041): from +49 5223 63406, page 3 in 0:05, INF, 3.85 line/mm, 2-D MR, 14400 b May 10 09:27:38.03: [ 556]: MODEM input buffering enabled May 10 09:27:38.03: [ 556]: MODEM set XON/XOFF/FLUSH: input ignored, output generated May 10 09:27:38.03: [ 556]: <-- [11:AT+FRM=146\r] May 10 09:27:41.14: [ 556]: --> [7:CONNECT] May 10 09:27:41.14: [ 556]: RECV: begin page May 10 09:27:41.25: [ 556]: RECV: 1 total lines, 0 bad lines, 0 consecutive bad lines May 10 09:27:41.25: [ 556]: RECV: end page May 10 09:27:41.25: [ 556]: --> [10:NO CARRIER] May 10 09:27:41.25: [ 556]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled May 10 09:27:41.25: [ 556]: MODEM input buffering disabled May 10 09:27:41.25: [ 556]: <-- [9:AT+FRH=3\r] May 10 09:27:41.29: [ 556]: --> [7:CONNECT] May 10 09:27:42.22: [ 556]: --> [2:OK] May 10 09:27:42.22: [ 556]: RECV recv DCN May 10 09:27:42.22: [ 556]: RECV FAX (00000041): recvq/fax00009.tif from +49 5223 63406, route to <unspecified>, 3 pages May 10 09:27:42.22: [ 556]: RECV FAX: COMREC received DCN May 10 09:27:42.22: [ 556]: <-- [9:AT+FTH=3\r] May 10 09:27:42.95: [ 556]: --> [10:NO CARRIER] May 10 09:27:42.95: [ 556]: MODEM input buffering enabled May 10 09:27:42.95: [ 556]: RECV FAX (00000041): session with +49 5223 63406 terminated abnormally: COMREC received DCN May 10 09:27:42.95: [ 556]: RECV FAX: bin/faxrcvd "recvq/fax00009.tif" "modem" "00000041" "COMREC received DCN" "" May 10 09:27:43.06: [ 556]: RECV FAX: end May 10 09:27:43.06: [ 556]: SESSION END
Hallo, On Fri, May 10, 2002 at 12:24:21PM +0200, Marco Zwillich wrote:
Ich habe hier ein kleines Problem mit dem Empfang mehrseitiger Fax mit Hylafax. Konfiguration: SuSE 7.2, Kernel 2.4.18-xfs, Hylafax 4.1, Sedlbauer Speedfax Pci.
Die erste Seite des Faxes kommt sauber an, weitere jedoch nicht.
ein Mitarbeiter von Sedlbauer schrieb mir, daß bei einigen Geräten mit 14400 bps Probleme beim Faxempfang auftreten können. Er empfahl, den Treiber der ISDN-Karte auf 9600 bps zu beschränken, indem in der Datei isar.c die Zeilen const u_char faxmodulation_s[] = "3,24,48,72,73,74,96,97,98,121,122,145,146"; const u_char faxmodulation[] = {3,24,48,72,73,74,96,97,98,121,122,145,146}; #define FAXMODCNT 13 durch die Zeilen const u_char faxmodulation_s[] = "3,24,48,72,96"; const u_char faxmodulation[] = {3,24,48,72,96}; #define FAXMODCNT 5 ersetzt werden. Anschließend neu übersetzen (Stand: 19.04.2002). An anderer Stelle wird empfohlen, in /var/spool/fax/etc/config.ttyI0 Class1SwitchingDelay von 150 auf einen kleineren Wert zu setzen (z.B. 75 oder 30), siehe beispielsweise http://groups.google.com/groups?selm=fa.jf3a8pv.q2m8pd%40ifi.uio.no Unten im Log ist Class1SwitchingDelay wohl auf 150 ms gesetzt.
May 10 09:27:28.12: [ 556]: MODEM input buffering disabled May 10 09:27:28.12: [ 556]: <-- [9:AT+FRH=3\r] May 10 09:27:28.16: [ 556]: --> [7:CONNECT] May 10 09:27:29.23: [ 556]: --> [2:OK] May 10 09:27:29.23: [ 556]: RECV recv MPS (more pages, same document) May 10 09:27:29.23: [ 556]: DELAY 150 ms May 10 09:27:29.38: [ 556]: <-- [9:AT+FTH=3\r] May 10 09:27:29.38: [ 556]: --> [10:NO CARRIER] May 10 09:27:29.38: [ 556]: RECV send MCF (message confirmation)
Sicherer ist wahrscheinlich die Begrenzung auf 9600 bps. Viele Grüße Sascha Rogmann
participants (2)
-
Marco Zwillich -
Sascha Rogmann