Hallo zusammen, ich habe mit AVM DSL USB 2.0 und SuSE 9.2 einen Router aufgebaut. Im Prinzip klappt das. Leider stelle ich regelmäßige Verbindungsabbrüche fest. Hier z.B. nach 235 Minuten. Feb 13 12:05:08 server pppd[20401]: Hangup (SIGHUP) Feb 13 12:05:08 server pppd[20401]: capiplugin: disconnect(remote): "" -> "" outgoing 0x0000 (0x3326) - No additional information Feb 13 12:05:08 server pppd[20401]: Modem hangup Feb 13 12:05:08 server pppd[20401]: capiplugin: phase network (was running). Feb 13 12:05:08 server pppd[20401]: restoring old default route to eth0 [192.168.2.1] Feb 13 12:05:08 server pppd[20401]: capiplugin: phase establish (was network). Feb 13 12:05:08 server pppd[20401]: capiplugin: phase dead (was establish). Feb 13 12:05:08 server pppd[20401]: Connection terminated. Feb 13 12:05:08 server pppd[20401]: Connect time 235.1 minutes. Feb 13 12:05:08 server pppd[20401]: Sent 2317609 bytes, received 14116475 bytes. Feb 13 12:05:08 server pppd[20401]: capiplugin: phase disconnect (was dead). Feb 13 12:05:08 server pppd[20401]: Terminating on signal 15. Feb 13 12:05:09 server ip-down: SuSEfirewall2: Firewall customary rules loaded from /etc/sysconfig/scripts/SuSEfirewall2-custom Feb 13 12:05:09 server SuSEfirewall2: Firewall customary rules loaded from /etc/sysconfig/scripts/SuSEfirewall2-custom Feb 13 12:05:13 server ip-down: SuSEfirewall2: Firewall rules successfully set from /etc/sysconfig/SuSEfirewall2 Feb 13 12:05:13 server SuSEfirewall2: Firewall rules successfully set from /etc/sysconfig/SuSEfirewall2 Feb 13 12:05:13 server pppd[20401]: Script /etc/ppp/ip-down finished (pid 21549), status = 0x0 Feb 13 12:05:13 server pppd[20401]: Connect time 235.1 minutes. Feb 13 12:05:13 server pppd[20401]: Sent 2317609 bytes, received 14116475 bytes. Feb 13 12:05:13 server pppd[20401]: capiplugin: exit Feb 13 12:05:13 server pppd[20401]: Exit. Weiß jemand was das Grund (0x3326) für den Verbindungabbruch sein kann. Telekom und T-Online können keine Störung der Leitung feststellen. Sehr häufig klappt ein Reconnect nicht. Wird von einem cron Job durchgeführt: cinternet -i dsl0 -A Feb 11 20:10:02 server pppd[16983]: Plugin capiplugin.so loaded. Feb 11 20:10:02 server pppd[16983]: capiplugin: $Revision: 1.35 $ Feb 11 20:10:02 server pppd[16983]: capiconn: 1.9 Feb 11 20:10:02 server pppd[16983]: Plugin passwordfd.so loaded. Feb 11 20:10:02 server pppd[16983]: pppd 2.4.2 started by root, uid 0 Feb 11 20:10:02 server pppd[16983]: capiplugin: phase serialconn. Feb 11 20:10:02 server pppd[16983]: capiplugin: leased line (adslpppoe) Feb 11 20:10:05 server pppd[16983]: capiplugin: disconnect(remote): "" -> "" outgoing 0x0000 (0x3312) - No additional information Feb 11 20:10:10 server pppd[16983]: capiplugin: leased line (adslpppoe) Feb 11 20:10:14 server pppd[16983]: capiplugin: disconnect(remote): "" -> "" outgoing 0x0000 (0x3312) - No additional information Feb 11 20:10:19 server pppd[16983]: capiplugin: leased line (adslpppoe) Feb 11 20:10:22 server pppd[16983]: capiplugin: disconnect(remote): "" -> "" outgoing 0x0000 (0x3312) - No additional information Feb 11 20:10:27 server pppd[16983]: capiplugin: leased line (adslpppoe) Feb 11 20:10:31 server pppd[16983]: capiplugin: disconnect(remote): "" -> "" out going 0x0000 (0x3312) - No additional information Feb 11 20:10:31 server pppd[16983]: capiplugin: couldn't make connection Feb 11 20:10:31 server pppd[16983]: capiplugin: exit Feb 11 20:10:31 server pppd[16983]: Exit. Welcher Fehler (0x3312) wird hier erkannt? capiinfo gibt die folgende Ausgabe: Number of Controllers : 2 Controller 1: Manufacturer: AVM-GmbH CAPI Version: 2.0 Manufacturer Version: 3.101-04 (49.20) Serial Number: 0000000 BChannels: 2 Global Options: 0x00000039 internal controller supported DTMF supported Supplementary Services supported channel allocation supported (leased lines) B1 protocols support: 0x4000011f 64 kbit/s with HDLC framing 64 kbit/s bit-transparent operation V.110 asynconous operation with start/stop byte framing V.110 synconous operation with HDLC framing T.30 modem for fax group 3 Modem asyncronous operation with start/stop byte framing B2 protocols support: 0x00000b1b ISO 7776 (X.75 SLP) Transparent LAPD with Q.921 for D channel X.25 (SAPI 16) T.30 for fax group 3 ISO 7776 (X.75 SLP) with V.42bis compression V.120 asyncronous mode V.120 bit-transparent mode B3 protocols support: 0x800000bf Transparent T.90NL, T.70NL, T.90 ISO 8208 (X.25 DTE-DTE) X.25 DCE T.30 for fax group 3 T.30 for fax group 3 with extensions Modem 0100 0200 39000000 1f010040 1b0b0000 bf000080 00000000 00000000 00000000 00000000 00000000 00000000 01000001 00020000 00000000 00000000 00000000 Supplementary services support: 0x000003ff Hold / Retrieve Terminal Portability ECT 3PTY Call Forwarding Call Deflection MCID CCBS Controller 2: Manufacturer: AVM-GmbH CAPI Version: 2.0 Manufacturer Version: 3.101-04 (49.20) Serial Number: 0000000 BChannels: 1 Global Options: 0x00000001 internal controller supported B1 protocols support: 0x10000000 B2 protocols support: 0x40000002 Transparent B3 protocols support: 0x40000001 Transparent 0100 0100 01000000 00000010 02000040 01000040 00000000 00000000 00000000 00000000 00000000 00000000 01000001 00020000 00000000 00000000 00000000 Supplementary services support: 0x000003ff Hold / Retrieve Terminal Portability ECT 3PTY Call Forwarding Call Deflection MCID CCBS drdsl gibt aktuell die folgende Auskunft, d.h. während des Betriebs des DSL Adapters: DSL Assistant version 1.0.4 copyright AVM 2004 The DSL Assistant is examining your DSL configuration... The DSL-Controller has the number 2. Searching for remote vendor ID... (This could take over a minute) ERROR: DSL-Controller 2 is not synced! Davor als der Controller mal wieder nicht funktionierte, habe ich folgende Meldung erhalten: DSL Assistant version 1.0.4 copyright AVM 2004 The DSL Assistant is examining your DSL configuration... The DSL-Controller has the number 2. Searching for remote vendor ID... (This could take over a minute) Found remote vendor: U-R2 (Texas Instruments) Testing different config values, please wait... Cannot find any working values -> using default values! Found following values for DSL: controller 2 protocol adslpppoe vpi 1 vci 32 vcc 1 Wie kann man die Verbindungsabbrüche unterbinden? Liegt es vielleicht doch an Telekom oder T-Online? Vielen Dank für Eure Hilfe Tim