Fritz Card A1 irq Weiter Informationen

Liebe ISDNlerInnen, herzlichen Dank für einige Tipps. Aber ich gebe nochmals Detail: Ohne irgend etwas am Interrupt zu konfigurieren - LPT habe ich im BIOS auf not use gestellt, greift die Karte auf den irq 5 und liefert folgende Information in /var/log/messages Nov 15 09:57:40 zappa cardmgr[75]: executing: 'insmod /lib/modules/2.2.14/misc/hisax.o type=26 protocol=2' Nov 15 09:57:40 zappa cardmgr[75]: executing: 'insmod /lib/modules/2.2.14/pcmcia/avma1_cs.o' Nov 15 09:57:41 zappa cardmgr[75]: executing: './isdn start A1' Nov 15 09:57:42 zappa cardmgr[75]: + Loading ISDN drivers ... Nov 15 09:57:42 zappa cardmgr[75]: + /dev/isdnctrl: No such device <<------------------------!!!!!!!!!!! das verstehe ich auch nicht Nov 15 09:57:42 zappa cardmgr[75]: + adding default route 192.168.1.1 /dev/isdnctrl in ein ln auf isdnctrl0 Nov 15 09:57:42 zappa kernel: klogd 1.3-3, log source = /proc/kmsg started. Nov 15 09:57:42 zappa kernel: Inspecting /boot/System.map-2.2.14 Nov 15 09:57:43 zappa kernel: Loaded 9053 symbols from /boot/System.map-2.2.14. Nov 15 09:57:43 zappa kernel: Symbols match kernel version 2.2.14. Nov 15 09:57:43 zappa kernel: Loaded 132 symbols from 12 modules. Nov 15 09:57:43 zappa kernel: Serial driver version 4.27 with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ enabled Nov 15 09:57:43 zappa kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A Nov 15 09:57:43 zappa kernel: Linux PCMCIA Card Services 3.1.11 Nov 15 09:57:43 zappa kernel: kernel build: 2.2.14 #1 Sat Mar 25 00:46:59 GMT 2000 Nov 15 09:57:43 zappa kernel: options: [pci] [cardbus] [apm] Nov 15 09:57:43 zappa kernel: PCI routing table version 1.0 at 0xf7350 Nov 15 09:57:43 zappa kernel: 00:0b.0 -> irq 11 Nov 15 09:57:43 zappa kernel: 00:0b.1 -> irq 11 Nov 15 09:57:43 zappa kernel: Intel PCIC probe: Nov 15 09:57:43 zappa kernel: Bridge register mapping failed: check cb_mem_base setting Nov 15 09:57:43 zappa kernel: not found. Nov 15 09:57:43 zappa kernel: Intel PCIC probe: Nov 15 09:57:43 zappa kernel: Toshiba ToPIC97 PCI-to-CardBus at slot 00:0b, mem 0x68000000 Nov 15 09:57:43 zappa kernel: host opts [0]: [slot 0xf0] [ccr 0x10] [cdr 0x86] [rcr 0x02] [pci irq 11] [lat 168/176] [bus 20/20] Nov 15 09:57:43 zappa kernel: host opts [1]: [slot 0xf0] [ccr 0x20] [cdr 0x86] [rcr 0x02] [pci irq 11] [lat 168/176] [bus 21/21] Nov 15 09:57:43 zappa kernel: ISA irqs (default) = 3,4,5,7,9,10,12 PCI status changes Nov 15 09:57:43 zappa kernel: cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff Nov 15 09:57:43 zappa kernel: cs: IO port probe 0x0800-0x08ff: clean. Nov 15 09:57:43 zappa kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x220-0x22f 0x330-0x337 0x378-0x37f 0x388-0x38f 0x4d0-0x4d7 Nov 15 09:57:43 zappa kernel: cs: IO port probe 0x0a00-0x0aff: clean. Nov 15 09:57:43 zappa kernel: cs: memory probe 0x0d0000-0x0dffff: clean. Nov 15 09:57:43 zappa kernel: xirc2ps_cs.c 1.31 1998/12/09 19:32:55 (dd9jn+kvh) Nov 15 09:57:43 zappa kernel: eth0: Xircom: port 0x2e0, irq 3, hwaddr 00:80:C7:5F:0F:B9 Nov 15 09:57:43 zappa kernel: tty01 at 0x02f8 (irq = 3) is a 16450 Nov 15 09:57:43 zappa kernel: eth0: media 10BaseT, silicon revision 1 Nov 15 09:57:43 zappa kernel: CSLIP: code copyright 1989 Regents of the University of California Nov 15 09:57:43 zappa kernel: ISDN subsystem Rev: 1.97/1.82/1.103/1.61/1.17/1.3 loaded Nov 15 09:57:43 zappa kernel: avma1_cs: testing i/o 0x140-0x148 Nov 15 09:57:43 zappa kernel: avma1_cs: checking at i/o 0x140, irq 5 Nov 15 09:57:43 zappa kernel: HiSax: Linux Driver for passive ISDN cards Nov 15 09:57:43 zappa kernel: HiSax: Version 3.3d (module) Nov 15 09:57:43 zappa kernel: HiSax: Layer1 Revision 2.37 Nov 15 09:57:43 zappa kernel: HiSax: Layer2 Revision 2.20 Nov 15 09:57:43 zappa kernel: HiSax: TeiMgr Revision 2.13 Nov 15 09:57:43 zappa kernel: HiSax: Layer3 Revision 2.10 Nov 15 09:57:43 zappa kernel: HiSax: LinkLayer Revision 2.40 Nov 15 09:57:43 zappa kernel: HiSax: Approval certification valid Nov 15 09:57:43 zappa kernel: HiSax: Approved with ELSA Quickstep series cards Nov 15 09:57:43 zappa kernel: HiSax: Approval registration numbers: Nov 15 09:57:43 zappa kernel: HiSax: German D133361J CETECOM ICT Services GmbH Nov 15 09:57:43 zappa kernel: HiSax: EU (D133362J) CETECOM ICT Services GmbH Nov 15 09:57:43 zappa kernel: HiSax: Approved with Eicon Technology Diva 2.01 PCI cards Nov 15 09:57:43 zappa kernel: HiSax: Total 1 card defined Nov 15 09:57:43 zappa kernel: HiSax: Card 1 Protocol EDSS1 Id=HiSax (0) Nov 15 09:57:43 zappa kernel: HiSax: AVM A1 PCMCIA driver Rev. 2.5 Nov 15 09:57:43 zappa kernel: AVM A1 PCMCIA: io 0x140 irq 5 model 1 version 2 Nov 15 09:57:43 zappa kernel: AVM A1 PCMCIA: ISAC version (0): 2086/2186 V1.1 Nov 15 09:57:43 zappa kernel: AVM A1 PCMCIA: HSCX version A: V2.1 B: V2.1 Nov 15 09:57:43 zappa kernel: AVM A1 (PCMCIA): IRQ 5 count 0 Nov 15 09:57:43 zappa kernel: AVM A1 (PCMCIA): IRQ 5 count 0 Nov 15 09:57:43 zappa kernel: AVM A1 (PCMCIA): IRQ(5) getting no interrupts during init 1 <<-------------------------!!!!!!!!!!!!! Nov 15 09:57:43 zappa kernel: AVM A1 (PCMCIA): IRQ 5 count 0 Nov 15 09:57:43 zappa kernel: AVM A1 (PCMCIA): IRQ(5) getting no interrupts during init 2 Nov 15 09:57:43 zappa kernel: AVM A1 (PCMCIA): IRQ 5 count 0 Nov 15 09:57:43 zappa kernel: AVM A1 (PCMCIA): IRQ(5) getting no interrupts during init 3 Nov 15 09:57:43 zappa kernel: HiSax: Card AVM A1 (PCMCIA) not installed ! Nov 15 09:57:43 zappa kernel: HiSax: module installed Ich schaue unter NT nach welcher Interrupt die AVM-Karte dort benützt es ist irq=7. Konfiguriere ich die /etc/pcmcia/config mit opt irq_list=7 ==> /var/adm/messages: Dec 11 08:22:53 zappa syslogd 1.3-3: restart. Dec 11 08:22:53 zappa cardmgr[75]: executing: 'insmod /lib/modules/2.2.14/misc/hisax.o type=26 protocol=2' Dec 11 08:22:53 zappa cardmgr[75]: executing: 'insmod /lib/modules/2.2.14/pcmcia/avma1_cs.o irq_list=7' <----------- Dec 11 08:22:54 zappa cardmgr[75]: get dev info on socket 0 failed: No such device <-----------------------------!!!! Dec 11 08:22:55 zappa kernel: klogd 1.3-3, log source = /proc/kmsg started. Dec 11 08:22:55 zappa kernel: Inspecting /boot/System.map-2.2.14 [...] Dec 11 08:22:56 zappa kernel: CSLIP: code copyright 1989 Regents of the University of California Dec 11 08:22:56 zappa kernel: ISDN subsystem Rev: 1.97/1.82/1.103/1.61/1.17/1.3 loaded Dec 11 08:22:56 zappa kernel: avma1_cs: testing i/o 0x140-0x148 Dec 11 08:22:56 zappa kernel: avma1_cs: RequestIRQ: Resource in use <--------------!!!!!!!!!!!!!!!!!!!!! Dec 11 08:22:56 zappa kernel: cat uses obsolete /proc/pci interface Dec 11 08:22:56 zappa kernel: usb-uhci.c: version v1.184 time 01:08:13 Mar 25 2000 Dec 11 08:22:56 zappa kernel: usb-uhci.c: Detected 2 ports Dec 11 08:22:56 zappa kernel: usb.c: new USB bus registered, assigned bus number 1 So, jetzt biete ich irq_list 7,9,10,11,12 an und was sehe ich vgl. /var/log/messages: Dec 11 15:05:50 zappa cardmgr[75]: executing: 'insmod /lib/modules/2.2.14/pcmcia/avma1_cs.o irq_list=7,9,10,11,12' Dec 11 15:05:50 zappa cardmgr[75]: executing: './isdn start A1' Dec 11 15:05:51 zappa cardmgr[75]: + Loading ISDN drivers ... Dec 11 15:05:51 zappa cardmgr[75]: + /dev/isdnctrl: No such device Dec 11 15:05:51 zappa cardmgr[75]: + adding default route 192.168.1.1 Dec 11 15:05:52 zappa kernel: klogd 1.3-3, log source = /proc/kmsg started. Dec 11 15:05:52 zappa kernel: Inspecting /boot/System.map-2.2.14 Dec 11 15:05:52 zappa kernel: Loaded 9053 symbols from /boot/System.map-2.2.14. Dec 11 15:05:52 zappa kernel: Symbols match kernel version 2.2.14. Dec 11 15:05:52 zappa kernel: Loaded 132 symbols from 12 modules. Dec 11 15:05:52 zappa kernel: Serial driver version 4.27 with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ enabled Dec 11 15:05:52 zappa kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A Dec 11 15:05:52 zappa kernel: Linux PCMCIA Card Services 3.1.11 Dec 11 15:05:52 zappa kernel: kernel build: 2.2.14 #1 Sat Mar 25 00:46:59 GMT 2000 Dec 11 15:05:52 zappa kernel: options: [pci] [cardbus] [apm] Dec 11 15:05:52 zappa kernel: PCI routing table version 1.0 at 0xf7350 Dec 11 15:05:52 zappa kernel: 00:0b.0 -> irq 11 Dec 11 15:05:52 zappa kernel: 00:0b.1 -> irq 11 Dec 11 15:05:52 zappa kernel: Intel PCIC probe: Dec 11 15:05:52 zappa kernel: Bridge register mapping failed: check cb_mem_base setting Dec 11 15:05:52 zappa kernel: not found. Dec 11 15:05:52 zappa kernel: Intel PCIC probe: Dec 11 15:05:52 zappa kernel: Toshiba ToPIC97 PCI-to-CardBus at slot 00:0b, mem 0x68000000 Dec 11 15:05:52 zappa kernel: host opts [0]: [slot 0xf0] [ccr 0x10] [cdr 0x86] [rcr 0x02] [pci irq 11] [lat 168/176] [bus 20/20] Dec 11 15:05:52 zappa kernel: host opts [1]: [slot 0xf0] [ccr 0x20] [cdr 0x86] [rcr 0x02] [pci irq 11] [lat 168/176] [bus 21/21] Dec 11 15:05:52 zappa kernel: ISA irqs (default) = 3,4,5,7,9,10,12 PCI status changes Dec 11 15:05:52 zappa kernel: cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff Dec 11 15:05:52 zappa kernel: cs: IO port probe 0x0800-0x08ff: clean. Dec 11 15:05:52 zappa kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x220-0x22f 0x330-0x337 0x378-0x37f 0x388-0x38f 0x4d0-0x4d7 Dec 11 15:05:52 zappa kernel: cs: IO port probe 0x0a00-0x0aff: clean. Dec 11 15:05:52 zappa kernel: cs: memory probe 0x0d0000-0x0dffff: clean. Dec 11 15:05:52 zappa kernel: xirc2ps_cs.c 1.31 1998/12/09 19:32:55 (dd9jn+kvh) Dec 11 15:05:52 zappa kernel: eth0: Xircom: port 0x2e0, irq 3, hwaddr 00:80:C7:5F:0F:B9 Dec 11 15:05:52 zappa kernel: tty01 at 0x02f8 (irq = 3) is a 16450 Dec 11 15:05:52 zappa kernel: eth0: media 10BaseT, silicon revision 1 Dec 11 15:05:52 zappa kernel: CSLIP: code copyright 1989 Regents of the University of California Dec 11 15:05:52 zappa kernel: ISDN subsystem Rev: 1.97/1.82/1.103/1.61/1.17/1.3 loaded Dec 11 15:05:52 zappa kernel: avma1_cs: testing i/o 0x140-0x148 Dec 11 15:05:52 zappa kernel: avma1_cs: checking at i/o 0x140, irq 9 Dec 11 15:05:52 zappa kernel: HiSax: Linux Driver for passive ISDN cards Dec 11 15:05:52 zappa kernel: HiSax: Version 3.3d (module) Dec 11 15:05:52 zappa kernel: HiSax: Layer1 Revision 2.37 Dec 11 15:05:52 zappa kernel: HiSax: Layer2 Revision 2.20 Dec 11 15:05:52 zappa kernel: HiSax: TeiMgr Revision 2.13 Dec 11 15:05:52 zappa kernel: HiSax: Layer3 Revision 2.10 Dec 11 15:05:52 zappa kernel: HiSax: LinkLayer Revision 2.40 Dec 11 15:05:52 zappa kernel: HiSax: Approval certification valid Dec 11 15:05:52 zappa kernel: HiSax: Approved with ELSA Quickstep series cards Dec 11 15:05:52 zappa kernel: HiSax: Approval registration numbers: Dec 11 15:05:52 zappa kernel: HiSax: German D133361J CETECOM ICT Services GmbH Dec 11 15:05:52 zappa kernel: HiSax: EU (D133362J) CETECOM ICT Services GmbH Dec 11 15:05:52 zappa kernel: HiSax: Approved with Eicon Technology Diva 2.01 PCI cards Dec 11 15:05:52 zappa kernel: HiSax: Total 1 card defined Dec 11 15:05:52 zappa kernel: HiSax: Card 1 Protocol EDSS1 Id=HiSax (0) Dec 11 15:05:52 zappa kernel: HiSax: AVM A1 PCMCIA driver Rev. 2.5 Dec 11 15:05:52 zappa kernel: AVM A1 PCMCIA: io 0x140 irq 9 model 1 version 2 Dec 11 15:05:52 zappa kernel: AVM A1 PCMCIA: ISAC version (0): 2086/2186 V1.1 Dec 11 15:05:52 zappa kernel: AVM A1 PCMCIA: HSCX version A: V2.1 B: V2.1 Dec 11 15:05:52 zappa kernel: AVM A1 (PCMCIA): IRQ 9 count 0 Dec 11 15:05:52 zappa kernel: AVM A1 (PCMCIA): IRQ 9 count 0 Dec 11 15:05:52 zappa kernel: AVM A1 (PCMCIA): IRQ(9) getting no interrupts during init 1 <---------------!!!!!!!!!!!!!!!!!!!! Dec 11 15:05:52 zappa kernel: AVM A1 (PCMCIA): IRQ 9 count 0 Dec 11 15:05:52 zappa kernel: AVM A1 (PCMCIA): IRQ(9) getting no interrupts during init 2 Dec 11 15:05:52 zappa kernel: AVM A1 (PCMCIA): IRQ 9 count 0 Dec 11 15:05:52 zappa kernel: AVM A1 (PCMCIA): IRQ(9) getting no interrupts during init 3 Dec 11 15:05:52 zappa kernel: HiSax: Card AVM A1 (PCMCIA) not installed ! Dec 11 15:05:52 zappa kernel: HiSax: module installed Dec 11 15:05:53 zappa kernel: cat uses obsolete /proc/pci interface Ich hoffen jemand hat noch ein Tipp :-)) Ich dnake allen mfg rb -- Rudolf Börner Fa. Streck Transport GmbH Abt. Informatik (Netzwerkmanager (WAN/LAN)) Blankreutestr. 6 79108 Freiburg T: ++ (0)761/1305-157 F: ++ (0)761/1305-159 mailto: rudolf.boerner@streck.de http://www.streck.de
participants (1)
-
Boerner, Rudolf