Volker.Kochan@warnermusic.com wrote:

Hallo zusammen,

hat eventuell jemand Erfahrung mit der Fritz Card. Ich fahre die SUSE 6.1 mit 2.2.7 Kernel. Leider kann ich die ISDN-Karte nicht dazu überreden, ihren Dienst aufzunehmen. Im Kernel habe ich den Support für AVM B1 enabled und versuche die Karte über ein Modul anzuprechen, leider bisher ohne Erfolg. Weiss jemand Rat !?!?!?

Hallo Volker, bitte im Kernel statt B1 die Fritz PCI/pnp und Euro-ISDN auswählen. Diese Karte ist Typ 27. Dann cd/etc pnpdump > isapnp.conf Diese editieren (funktionierende Version anbei) und in /proc/interrupts und /proc/ioports nachsehen, was noch frei ist. Gruß Chris # $Id: pnpdump.c,v 1.18 1999/02/14 22:47:18 fox Exp $ # This is free software, see the sources for details. # This software has NO WARRANTY, use at your OWN RISK # # For details of this file format, see isapnp.conf(5) # # For latest information and FAQ on isapnp and pnpdump see: # http://www.roestock.demon.co.uk/isapnptools/ # # Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR # # Trying port address 0203 # Trying port address 020b # Board 1 has serial identifier 6d ff ff ff ff f0 00 8c 0e # Board 2 has serial identifier c6 ff ff ff ff 00 09 cd 06 # (DEBUG) (READPORT 0x020b) (ISOLATE PRESERVE) (IDENTIFY *) (VERBOSITY 2) (CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING # Card 1: (serial identifier 6d ff ff ff ff f0 00 8c 0e) # Vendor Id CTL00f0, No Serial Number (-1), checksum 0x6D. # Version 1.0, Vendor version 1.0 # ANSI string -->Creative ViBRA16X PnP<-- # # Logical device id CTL0043 # Device supports vendor reserved register @ 0x38 # Device supports vendor reserved register @ 0x39 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE CTL00f0/-1 (LD 0 # ANSI string -->Audio<-- # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # IRQ 5. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 1. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 1)) # Next DMA channel 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 3)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0220 # IO base alignment 1 bytes # Number of IO addresses required: 16 # (IO 0 (SIZE 16) (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0330 # Maximum IO base address 0x0330 # IO base alignment 1 bytes # Number of IO addresses required: 2 # (IO 1 (SIZE 2) (BASE 0x0330)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 1 bytes # Number of IO addresses required: 4 # (IO 2 (SIZE 4) (BASE 0x0388)) # Start dependent functions: priority acceptable # IRQ 5, 7, 9 or 10. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Next DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 0)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (SIZE 16) (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0330 # IO base alignment 48 bytes # Number of IO addresses required: 2 # (IO 1 (SIZE 2) (BASE 0x0300)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 1 bytes # Number of IO addresses required: 4 # (IO 2 (SIZE 4) (BASE 0x0388)) # Start dependent functions: priority acceptable # IRQ 5, 7, 9 or 10. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Next DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 0)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (SIZE 16) (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0330 # IO base alignment 48 bytes # Number of IO addresses required: 2 # (IO 1 (SIZE 2) (BASE 0x0300)) # Start dependent functions: priority acceptable # IRQ 5, 7, 9 or 10. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Next DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 0)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (SIZE 16) (BASE 0x0220)) # Start dependent functions: priority functional # IRQ 5, 7, 9 or 10. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (SIZE 16) (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0330 # IO base alignment 16 bytes # Number of IO addresses required: 2 # (IO 1 (SIZE 2) (BASE 0x0300)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0394 # IO base alignment 4 bytes # Number of IO addresses required: 4 # (IO 2 (SIZE 4) (BASE 0x0388)) # Start dependent functions: priority functional # IRQ 5, 7, 9 or 10. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (SIZE 16) (BASE 0x0220)) # End dependent functions (NAME "CTL00f0/-1[0]{Audio }") # (ACT Y) )) # # Logical device id CTL7005 # Device supports vendor reserved register @ 0x38 # Device supports vendor reserved register @ 0x39 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE CTL00f0/-1 (LD 1 # Compatible device id PNPb02f # ANSI string -->Game<-- # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0201 # Maximum IO base address 0x0201 # IO base alignment 1 bytes # Number of IO addresses required: 1 # (IO 0 (SIZE 1) (BASE 0x0201)) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0200 # Maximum IO base address 0x020f # IO base alignment 1 bytes # Number of IO addresses required: 1 # (IO 0 (SIZE 1) (BASE 0x0200)) # End dependent functions (NAME "CTL00f0/-1[1]{Game }") (ACT Y) )) # End tag... Checksum 0x00 (OK) # Card 2: (serial identifier c6 ff ff ff ff 00 09 cd 06) # Vendor Id AVM0900, No Serial Number (-1), checksum 0xC6. # Version 1.0, Vendor version 0.0 # ANSI string -->AVM ISDN-Controller FRITZ!Card<-- # # Logical device id AVM0900 # Device support I/O range check register # Device supports vendor reserved register @ 0x38 # Device supports vendor reserved register @ 0x39 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE AVM0900/-1 (LD 0 # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0200 # Maximum IO base address 0xffe0 # IO base alignment 32 bytes # Number of IO addresses required: 32 (IO 0 (SIZE 32) (BASE 0x0240)) # IRQ 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15. # High true, edge sensitive interrupt (INT 0 (IRQ 10 (MODE +E))) (NAME "AVM0900/-1[0]{AVM ISDN-Controller FRITZ!Card}") (ACT Y) )) # End tag... Checksum 0x00 (OK) # Returns all cards to the "Wait for Key" state (WAITFORKEY)

Christian Otto-Lange wrote:

Volker.Kochan@warnermusic.com wrote:

...

Weiss jemand Rat !?!?!?

Hallo Volker,

bitte im Kernel statt B1 die Fritz PCI/pnp und Euro-ISDN auswählen. Diese Karte ist Typ 27. Dann cd/etc pnpdump > isapnp.conf Diese editieren (funktionierende Version anbei) und in /proc/interrupts und /proc/ioports nachsehen, was noch frei ist.

Da habe ich noch vergessen: isapnp isapnp.conf Gruß Chris P.S: Sorry wg.des zu lang geratenen Attachments