Sedlbauer Speed Fax Isdn +

16 Dec 2002

      Hallo,

ich habe folgendes problem mit SuSE Linux 7.2 und selbst kompilierten kernel 2.4.20:

hisax treiber wird modular mit type=28 protocol=2 geladen und laut syslog auf ohne fehler.
ISAR firmware wird mit hisaxctrl mit dem parameter HiSax 9 isar.bin geladen, und laut syslog auch ohne fehler.

siehe syslog auszüge:

Dec 16 19:44:20 testpc214 kernel: Inspecting /boot/System.map
Dec 16 19:44:20 testpc214 kernel: Loaded 17097 symbols from /boot/System.map.
Dec 16 19:44:20 testpc214 kernel: Symbols match kernel version 2.4.20.
Dec 16 19:44:20 testpc214 kernel: Loaded 77 symbols from 6 modules.
Dec 16 19:44:20 testpc214 kernel: isapnp: Scanning for PnP cards...
Dec 16 19:44:20 testpc214 kernel: isapnp: No Plug & Play device found
Dec 16 19:44:20 testpc214 kernel: CSLIP: code copyright 1989 Regents of the University of California
Dec 16 19:44:20 testpc214 kernel: ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/none/1.1.4.1 loaded
Dec 16 19:44:20 testpc214 kernel: HiSax: Linux Driver for passive ISDN cards
Dec 16 19:44:20 testpc214 kernel: HiSax: Version 3.5 (module)
Dec 16 19:44:20 testpc214 kernel: HiSax: Layer1 Revision 1.1.4.1
Dec 16 19:44:20 testpc214 kernel: HiSax: Layer2 Revision 1.1.4.1
Dec 16 19:44:20 testpc214 kernel: HiSax: TeiMgr Revision 1.1.4.1
Dec 16 19:44:20 testpc214 kernel: HiSax: Layer3 Revision 1.1.4.1
Dec 16 19:44:20 testpc214 kernel: HiSax: LinkLayer Revision 1.1.4.1
Dec 16 19:44:20 testpc214 kernel: HiSax: Approval certification valid
Dec 16 19:44:20 testpc214 kernel: HiSax: Approved with ELSA Microlink PCI cards
Dec 16 19:44:20 testpc214 kernel: HiSax: Approved with Eicon Technology Diva 2.01 PCI cards
Dec 16 19:44:20 testpc214 kernel: HiSax: Approved with Sedlbauer Speedfax + cards
Dec 16 19:44:20 testpc214 kernel: HiSax: Approved with HFC-S PCI A based cards
Dec 16 19:44:20 testpc214 kernel: HiSax: Total 1 card defined
Dec 16 19:44:20 testpc214 kernel: HiSax: Card 1 Protocol EDSS1 Id=HiSax (0)
Dec 16 19:44:20 testpc214 kernel: HiSax: Sedlbauer driver Rev. 1.1.4.1
Dec 16 19:44:20 testpc214 kernel: Sedlbauer: PCI subvendor:54 subid 1
Dec 16 19:44:20 testpc214 kernel: Sedlbauer: PCI base adr 0x1800
Dec 16 19:44:20 testpc214 kernel: Sedlbauer: defined at 0x1800-0x1900 IRQ 9
Dec 16 19:44:20 testpc214 kernel: Sedlbauer: speed fax+ pci detected
Dec 16 19:44:20 testpc214 kernel: Sedlbauer: ISAC version (0): 2086/2186 V1.1
Dec 16 19:44:20 testpc214 kernel: Sedlbauer: resetting card
Dec 16 19:44:20 testpc214 kernel: Sedlbauer: ISAR version 1
Dec 16 19:44:20 testpc214 kernel: Sedlbauer Speed Fax +: IRQ 9 count 0
Dec 16 19:44:20 testpc214 kernel: Sedlbauer Speed Fax +: IRQ 9 count 6
Dec 16 19:44:20 testpc214 kernel: HiSax: DSS1 Rev. 1.1.4.1
Dec 16 19:44:20 testpc214 kernel: HiSax: 2 channels added
Dec 16 19:44:20 testpc214 kernel: HiSax: MAX_WAITING_CALLS added
Dec 16 19:44:20 testpc214 kernel: isdn: Verbose-Level is 3

Dec 16 19:45:44 testpc214 kernel: Sedlbauer: resetting card
Dec 16 19:45:45 testpc214 kernel: Testing ISAR version 1
Dec 16 19:45:45 testpc214 kernel: isar_load_firmware buf 0x8049db0
Dec 16 19:45:45 testpc214 kernel: isar_load_firmware size: 62518
Dec 16 19:45:45 testpc214 kernel: isar firmware block (0x8000,30289,0x31)
Dec 16 19:45:45 testpc214 kernel: isar firmware block 30289 words loaded
Dec 16 19:45:45 testpc214 kernel: isar firmware block (0xf9a0,  934,0x17)
Dec 16 19:45:45 testpc214 kernel: isar firmware block   934 words loaded
Dec 16 19:45:45 testpc214 kernel: isar firmware block (0xffe5,   27,0x68)
Dec 16 19:45:45 testpc214 kernel: isar firmware block    27 words loaded
Dec 16 19:45:45 testpc214 kernel: isar start dsp success
Dec 16 19:45:45 testpc214 kernel: isar general status event f
Dec 16 19:45:45 testpc214 kernel: isar selftest OK
Dec 16 19:45:45 testpc214 kernel: isar software version 0x4

faxaddmodem von hylafax meldet jedoch:

Probing for best speed to talk to modem: 38400 OK.
[1]+  Terminated              ( trap "" 0 1 2; while true; do
    sleep 10; echo ""; echo "Hmm, something seems to be hung, check your modem eh?";
done )

The result of the AT+FCLASS=? command was:

ATQ0V1E1
OK
AT+FCLASS=?
ERROR

Kann mir jemand bei diesem problem weiterhelfen?!

Vielen Dank.

Mit freundlichen Grüßen

Peter Geiger
EDV-Compas GmbH