Hello community, here is the log from the commit of package i2c-tools for openSUSE:Factory checked in at 2014-06-26 08:00:19 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Comparing /work/SRC/openSUSE:Factory/i2c-tools (Old) and /work/SRC/openSUSE:Factory/.i2c-tools.new (New) ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Package is "i2c-tools" Changes: -------- --- /work/SRC/openSUSE:Factory/i2c-tools/i2c-tools.changes 2014-02-24 06:52:06.000000000 +0100 +++ /work/SRC/openSUSE:Factory/.i2c-tools.new/i2c-tools.changes 2014-06-26 08:00:24.000000000 +0200 @@ -1,0 +2,6 @@ +Thu Jun 19 07:40:41 UTC 2014 - jdelvare@suse.com + +- i2c-tools-r6250-ddr3-fix-ext-temp-refresh.diff: Fix DDR3 extended + temp range refresh rate decoding. + +------------------------------------------------------------------- New: ---- i2c-tools-r6250-ddr3-fix-ext-temp-refresh.diff ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Other differences: ------------------ ++++++ i2c-tools.spec ++++++ --- /var/tmp/diff_new_pack.esQM3D/_old 2014-06-26 08:00:25.000000000 +0200 +++ /var/tmp/diff_new_pack.esQM3D/_new 2014-06-26 08:00:25.000000000 +0200 @@ -27,6 +27,7 @@ Recommends: modules Source0: http://dl.lm-sensors.org/%{name}/releases/%{name}-%{version}.tar.bz2 Source1: http://dl.lm-sensors.org/%{name}/releases/%{name}-%{version}.tar.bz2.sig +Patch0: i2c-tools-r6250-ddr3-fix-ext-temp-refresh.diff Patch90: i2c-tools-hackweek-9-dependencies.diff Patch91: i2c-tools-hackweek-9-improve-DDR3-support.diff BuildRoot: %{_tmppath}/%{name}-%{version}-build @@ -48,6 +49,7 @@ %prep %setup -q +%patch0 -p1 %patch90 -p1 %patch91 -p1 ++++++ i2c-tools-r6250-ddr3-fix-ext-temp-refresh.diff ++++++ Subject: decode-dimms: Fix DDR3 extended temp range refresh rate decoding Upstream: yes (r6250) Based on a patch from Peter Missel. The meaning of byte 31, bit 1, was inverted. Also, this bit is only meaningful if the extended temperature range is supported (bit 0 is set.) --- i2c-tools-3.1/eeprom/decode-dimms (revision 6231) +++ i2c-tools-3.1/eeprom/decode-dimms (revision 6250) @@ -1289,8 +1289,9 @@ printl("DLL-Off Mode supported?", ($bytes->[30] & 128) ? "Yes" : "No"); printl("Operating temperature range", sprintf "0-%d degrees C", ($bytes->[31] & 1) ? 95 : 85); - printl("Refresh Rate in extended temp range", - ($bytes->[31] & 2) ? "2X" : "1X"); + printl_cond($bytes->[31] & 1, + "Refresh Rate in extended temp range", + ($bytes->[31] & 2) ? "1X" : "2X"); printl("Auto Self-Refresh?", ($bytes->[31] & 4) ? "Yes" : "No"); printl("On-Die Thermal Sensor readout?", ($bytes->[31] & 8) ? "Yes" : "No"); -- To unsubscribe, e-mail: opensuse-commit+unsubscribe@opensuse.org For additional commands, e-mail: opensuse-commit+help@opensuse.org