https://bugzilla.novell.com/show_bug.cgi?id=216599 Summary: Broadcom network card on E1405 laptop does not work under Xen kernel 2.6.18.1-7-xen Product: openSUSE 10.2 Version: Beta 1 Platform: x86-64 OS/Version: SuSE Other Status: NEW Severity: Major Priority: P5 - None Component: Xen AssignedTo: cgriffin@novell.com ReportedBy: jbarton@technicalworks.net QAContact: qa@suse.de I have a Dell E1405 laptop with 10.2 beta 1 x86_64 installed. The network card is a Broadcom BCM4401-B0 100Base-TX. The card works fine under 10.1, here is my lspci output in 10.1: 02:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) Subsystem: Dell Unknown device 01d8 Flags: bus master, fast devsel, latency 64, IRQ 177 Memory at df9fe000 (32-bit, non-prefetchable) [size=8K] Capabilities: [40] Power Management version 2 When I boot the 10.2 beta 1 Xen kernel, the network card fails to start. Here is what is logged during system boot: usb 2-1: new full speed USB device using uhci_hcd and address 2 b44.c:v1.01 (Jun 16, 2006) ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17 b44 0000:02:00.0: No usable DMA configuration, aborting. ACPI: PCI interrupt for device 0000:02:00.0 disabled b44: probe of 0000:02:00.0 failed with error -5 ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:0c:00.0 to 64 ipw3945: Detected Intel PRO/Wireless 3945ABG Network Connection PCI: Enabling device 0000:02:00.0 (0100 -> 0102) ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17 b44 0000:02:00.0: No usable DMA configuration, aborting. ACPI: PCI interrupt for device 0000:02:00.0 disabled b44: probe of 0000:02:00.0 failed with error -5 ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 19 (level, low) -> IRQ 18 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[df9fd800-df9fdfff] Max Packet=[2048] IR/IT contexts=[4/4] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17 sdhci: SDHCI controller found at 0000:02:01.1 [1180:0822] (rev 19) Here is the lspci output while in 10.2 beta 1, which seems to be different: 02:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) Subsystem: Dell Unknown device 01d8 Flags: fast devsel, IRQ 17 Memory at df9fe000 (32-bit, non-prefetchable) [disabled] [size=8K] Capabilities: [40] Power Management version 2 Also, I tried to remove the b44 module that was loaded, and then re-ran modprobe b44, but this caused the laptop to lock-up immediately, and it had to be power-cycled. The laptop is a Dell e1405 with a core 2 duo processor. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug, or are watching someone who is.