https://bugzilla.novell.com/show_bug.cgi?id=287076#c1 --- Comment #1 from Olaf Hering 2007-06-24 05:56:31 MST --- Created an attachment (id=148080) --> (https://bugzilla.novell.com/attachment.cgi?id=148080) bug287076-hwinfo.txt -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.

https://bugzilla.novell.com/show_bug.cgi?id=287076#c3 Holger Macht changed: What |Removed |Added ---------------------------------------------------------------------------- Status|NEW |NEEDINFO Info Provider| |olh@novell.com --- Comment #3 from Holger Macht 2007-08-13 04:16:32 MST --- But the desktop can do the fine tuning...and the two applets might have different defaults... Olaf, please exit any power management applet and try the following: The powersave command line client has two options regarding CPU frequency scaling: $ powersave -h [...] -g, --set-dynamic-performance set cpufreq dynamic performance -G, --get-dynamic-performance get cpufreq dynamic performance [...] With these options, you can finetune how the dynamic frequency algorithm works. It's a value between 1 and 100. The higher the value, the more often and the faster the frequency is switched up. For instance, if it is set to a value of 20, the frequency of the CPU is increased as soon as there is little load. A value of 95 means that the frequency should only be increased when there's really heavy load over quite some time. Hope you get the idea... -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.

https://bugzilla.novell.com/show_bug.cgi?id=287076#c5 Holger Macht changed: What |Removed |Added ---------------------------------------------------------------------------- Status|NEEDINFO |NEW Info Provider|olh@novell.com | --- Comment #5 from Holger Macht 2007-09-03 03:55:12 MST --- Hm, actually the bug or problem is that your system stalls at switching frequencies, it mustn't do that. Default performance value should be ok, so experimenting with the value can just help fixing the problem for you. Thomas, did you here about similar reports yet. If not, I doubt we can do much about it. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.

https://bugzilla.novell.com/show_bug.cgi?id=287076#c6 Thomas Renninger changed: What |Removed |Added ---------------------------------------------------------------------------- CC| |trenn@novell.com Status|NEEDINFO |NEW Info Provider|trenn@novell.com | --- Comment #6 from Thomas Renninger 2007-09-09 10:27:07 MST --- Is ondemand or userspace governor used? /sys/devices/system/cpu/cpu0/cpufreq/... Maybe compiling CPU_FREQ_DEBUG in and pass cpufreq.debug=7 boot parameter reveals something? Could be a real HW or low level driver problem? AFAIK PPC have some problems if there is too often switched, therefore ondemand must not be used (should not be compiled in?). 400 and 600 are the only two freqs available? Maybe it's an immediate jump over several freqs on too high load that causes this? -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.

https://bugzilla.novell.com/show_bug.cgi?id=287076#c8 Olaf Hering changed: What |Removed |Added ---------------------------------------------------------------------------- Status|NEEDINFO |RESOLVED Info Provider|olh@novell.com | Resolution| |WORKSFORME --- Comment #8 from Olaf Hering 2007-10-09 05:55:40 MST --- it is something which will happen only on the early g3 powerbooks. nothing we can fix. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.