https://bugzilla.suse.com/show_bug.cgi?id=1206674 https://bugzilla.suse.com/show_bug.cgi?id=1206674#c2 --- Comment #2 from simon becherer <simon@becherer.de> --- Same here, is reproduceable if you have a "bond" configuration (normal hardware configuration will work) (according to andrei at mailinglist users@lists.opensuse.org) long (about one year) not updated tumbleweed was running fine. then update to tumbleweed 20221228 and network is not working. now at 20230102 still same. here what i have, and a workaround later in this comment: if it is working, it looks like this: ================================================ wicked ifstatus all lo up link: #1, state up type: loopback config: compat:suse:/etc/sysconfig/network/ifcfg-lo leases: ipv4 static granted leases: ipv6 static granted addr: ipv4 127.0.0.1/8 [static] addr: ipv6 ::1/128 [static] enp3s0 enslaved link: #2, state up, mtu 1500, master bond0 type: ethernet, hwaddr 18:67:b0:b9:a6:58 config: compat:suse:/etc/sysconfig/network/ifcfg-enp3s0 wlp2s0 up link: #3, state up, mtu 1500 type: wireless, state established, ssid XAuaLiwaru9835, WPA2-PSK+WPA-PSK config: compat:suse:/etc/sysconfig/network/ifcfg-wlp2s0 bond0 up link: #4, state up, mtu 1500 type: bond, mode active-backup, hwaddr 18:67:b0:b9:a6:58 config: compat:suse:/etc/sysconfig/network/ifcfg-bond0 leases: ipv4 static granted addr: ipv4 192.168.0.23/24 [static] route: ipv4 default via 192.168.0.99 [static] ==================================== it is configured that if cable (enp3s0) is plugged in, it will use cable, and if not plugged in it will switch to whireless (wlp2s0) ==================================== if its not working (before starting manually) it has the status: "device-not-running" for enp3s0 wlp2s0 and bond0 ==================================== after playing around i found out that the command: ip link set enp3s0 up ip link set wlp2s0 up will bring the network cards UP, but this i have to enter manually, AND wicked ifup enp3s0 wicked ifup wlp2s0 will NOT bring the network cards UP. (therefore wicked will during boot hang and run out of time, then boot continues ========================================== here from boot: Dez 29 21:54:08 becherer7 systemd[1]: Starting wicked AutoIPv4 supplicant service... Dez 29 21:54:08 becherer7 systemd[1]: Starting wicked DHCPv4 supplicant service... Dez 29 21:54:08 becherer7 systemd[1]: Starting wicked DHCPv6 supplicant service... Dez 29 21:54:08 becherer7 systemd[1]: Started wicked DHCPv6 supplicant service. Dez 29 21:54:08 becherer7 systemd[1]: Started wicked DHCPv4 supplicant service. Dez 29 21:54:08 becherer7 systemd[1]: Started wicked AutoIPv4 supplicant service. Dez 29 21:54:08 becherer7 systemd[1]: Starting wicked network management service daemon... Dez 29 21:54:08 becherer7 systemd[1]: Started wicked network management service daemon. Dez 29 21:54:08 becherer7 systemd[1]: Starting wicked network nanny service... Dez 29 21:54:08 becherer7 systemd[1]: Started wicked network nanny service. Dez 29 21:54:08 becherer7 systemd[1]: Starting wicked managed network interfaces... Dez 29 21:54:38 becherer7 wicked[1227]: lo up Dez 29 21:54:38 becherer7 wicked[1227]: enp3s0 device-not-running Dez 29 21:54:38 becherer7 wicked[1227]: wlp2s0 device-not-running Dez 29 21:54:38 becherer7 wicked[1227]: bond0 device-not-running Dez 29 21:54:38 becherer7 systemd[1]: Finished wicked managed network interfaces. ================================================= and here when i try manually using wicked: Dez 29 22:19:14 becherer7 wickedd-nanny[1226]: device wlp2s0: call to org.opensuse.Network.Interface.waitLinkUp() failed: General failure Dez 29 22:19:14 becherer7 wickedd-nanny[1226]: wlp2s0: failed to bring up device, still continuing Dez 29 22:19:19 becherer7 wickedd-nanny[1226]: device enp3s0: call to org.opensuse.Network.Interface.waitLinkUp() failed: General failure Dez 29 22:19:19 becherer7 wickedd-nanny[1226]: enp3s0: failed to bring up device, still continuing =================================================== workaround for boot: as allesandro sturniolo wrote, use ip link set enp3s0 up ip link set wlp2s0 up (in my setup) so make a file netz-wicked-workaround.service --------file ---------------------------- [Unit] Description=netz-wicked-workaround After=wicked.service [Service] Type=simple ExecStart=/usr/bin/netz RemainAfterExit=no [Install] WantedBy=multi-user.target -------endfile -------------------------------- copy this to /etc/systemd/system -------------------------------------- make a file netz -------------- file (for my setup)------------- #!/bin/bash sudo ip link set wlp2s0 up sudo ip link set enp3s0 up ----------- endfile-------------------- copy it to /usr/bin/netz and give them executable rights ---------------------------------------- use yast2 to start the new service at boot netz-wicked-workaround.service ------------------------------------- simoN -- You are receiving this mail because: You are on the CC list for the bug.