https://bugzilla.novell.com/show_bug.cgi?id=450824
User lasse.penttinen@gmail.com added comment
https://bugzilla.novell.com/show_bug.cgi?id=450824#c2
--- Comment #2 from Lasse Penttinen 2008-12-02 06:49:25 MST ---
I can run Ubuntu, Mandriva and others on this as LiveCD. It has only 384mb RAM
but there is linux swap partition available. I have used 10.3 on this with
success. I am not 100% sure, but I think I also evaluated 11.0 on this PC.
It looks more like a failure to initialize the display, incorrect display
parameters or similar. In XFCE/safemode this runs nicely.
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.27.7-4-pae (geeko@buildhost) (gcc version 4.3.2
[gcc-4_3-branch revision 141291] (SUSE Linux) ) #1 SMP 2008-11-25 00:02:37
+0100
PAT WC disabled due to known CPU erratum.
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000017f70000 (usable)
BIOS-e820: 0000000017f70000 - 0000000017f7e000 (ACPI data)
BIOS-e820: 0000000017f7e000 - 0000000017f80000 (ACPI NVS)
BIOS-e820: 0000000017f80000 - 0000000018000000 (reserved)
BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
DMI present.
last_pfn = 0x17f70 max_arch_pfn = 0x1000000
kernel direct mapping tables up to 17f70000 @ 7000-d000
RAMDISK: 179e8000 - 17f5ffbb
ACPI: RSDP 000F73B0, 0024 (r2 IBM )
ACPI: XSDT 17F745AB, 0044 (r1 IBM TP-1D 1320 LTP 0)
ACPI: FACP 17F745EF, 0081 (r1 IBM TP-1D 1320 IBM 1)
ACPI: DSDT 17F746D6, 98B0 (r1 IBM TP-1D 1320 MSFT 100000D)
ACPI: FACS 17F7F000, 0040
ACPI: SSDT 17F746A3, 0033 (r1 IBM TP-1D 1320 MSFT 100000D)
ACPI: ECDT 17F7DF86, 0052 (r1 IBM TP-1D 1320 IBM 1)
ACPI: BOOT 17F7DFD8, 0028 (r1 IBM TP-1D 1320 LTP 1)
NUMA - single node, flat memory mode
Node: 0, start_pfn: 0, end_pfn: 17f70
Setting physnode_map array to node 0 for pfns:
0 4000 8000 c000 10000 14000
node 0 pfn: [0 - 17f70]
Reserving 1024 pages of KVA for lmem_map of node 0 at 17400
remove_active_range (0, 95232, 96256)
Reserving total of 400 pages for numa KVA remap
kva_start_pfn ~ 17000 max_low_pfn ~ 17f70
max_pfn = 17f70
0MB HIGHMEM available.
383MB LOWMEM available.
max_low_pfn = 17f70, highstart_pfn = 17f70
Low memory ends at vaddr d7f70000
node 0 will remap to vaddr d7000000 - d7400000
allocate_pgdat: node 0 NODE_DATA d7000000
remap_numa_kva: node 0
remap_numa_kva: d7000000 to pfn 00017400
remap_numa_kva: d7200000 to pfn 00017600
High memory starts at vaddr d7f70000
mapped low ram: 0 - 17f70000
low ram: 00000000 - 17f70000
bootmap 00002000 - 00004ff0
(11 early reservations) ==> bootmem [0000000000 - 0017f70000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 00006764dc] TEXT DATA BSS ==> [0000100000 - 00006764dc]
#4 [00179e8000 - 0017f5ffbb] RAMDISK ==> [00179e8000 - 0017f5ffbb]
#5 [0000677000 - 000067f000] INIT_PG_TABLE ==> [0000677000 - 000067f000]
#6 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000]
#7 [0000007000 - 000000c000] PGTABLE ==> [0000007000 - 000000c000]
#8 [0017400000 - 0017800000] KVA RAM ==> [0017400000 - 0017800000]
#9 [0017000000 - 0017400000] KVA PG ==> [0017000000 - 0017400000]
#10 [0000002000 - 0000005000] BOOTMAP ==> [0000002000 - 0000005000]
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00017f70
HighMem 0x00017f70 -> 0x00017f70
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x00017400
0: 0x00017800 -> 0x00017f70
On node 0 totalpages: 97039
free_area_init_node: node 0, pgdat d7000000, node_mem_map d7002000
DMA zone: 3963 pages, LIFO batch:0
Normal zone: 92213 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x1008
SMP: Allowing 1 CPUs, 0 hotplug CPUs
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffb000 (01002000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000
PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
Allocating PCI resources starting at 20000000 (gap: 18000000:e7800000)
PERCPU: Allocating 40092 bytes of per cpu data
NR_CPUS: 128, nr_cpu_ids: 1, nr_node_ids 8
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 96176
Policy zone: Normal
Kernel command line: root=/dev/disk/by-id/ata-HITACHI_DK23DA-30B_10M85R-part1
ide=nodma apm=off noresume nosmp maxcpus=0 edd=off powersaved=off nohz=off
highres=off processor.max_cstate=1 x11failsafe vga=0x314
Unknown boot option `processor.max_cstate=1': ignoring
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
TSC: PIT calibration confirmed by PMTIMER.
TSC: using PMTIMER calibration value
Detected 863.786 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Initializing HighMem for node 0 (00000000:00000000)
Memory: 372328k/392640k available (2423k kernel code, 19920k reserved, 1969k
data, 328k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xff8b6000 - 0xfffff000 (7460 kB)
pkmap : 0xff400000 - 0xff600000 (2048 kB)
vmalloc : 0xd8800000 - 0xff3fe000 ( 619 MB)
lowmem : 0xc0000000 - 0xd7f70000 ( 383 MB)
.init : 0xc0552000 - 0xc05a4000 ( 328 kB)
.data : 0xc035ddbb - 0xc054a200 (1969 kB)
.text : 0xc0100000 - 0xc035ddbb (2423 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
Calibrating delay loop (skipped), value calculated using timer frequency..
1727.57 BogoMIPS (lpj=3455144)
kdb version 4.4 by Keith Owens, Scott Lurndal. Copyright SGI, All Rights
Reserved
Security Framework initialized
SELinux: Disabled at boot.
AppArmor: AppArmor initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20080609
ACPI: Checking initramfs for custom DSDT
Parsing all Control Methods:
Table [DSDT](id 0001) - 1185 Objects with 57 Devices 350 Methods 19 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 1 Objects with 0 Devices 1 Methods 0 Regions
tbxface-0596 [00] tb_load_namespace : ACPI Tables successfully acquired
ACPI: setting ELCR to 0200 (from 0800)
evxfevnt-0091 [00] enable : Transition to ACPI mode successful
weird, boot CPU (#0) not listedby the BIOS.
SMP motherboard not detected.
Mapping cpu 0 to node 0
Local APIC not detected. Using dummy APIC emulation.
SMP disabled
Mapping cpu 0 to node 0
Brought up 1 CPUs
Total of 1 processors activated (1727.57 BogoMIPS).
CPU0 attaching NULL sched-domain.
net_namespace: 1044 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd8fe, last bus=8
PCI: Using configuration type 1 for base access
perfmon: version 2.82
perfmon: CPU hotplug support enabled
evgpeblk-0957 [00] ev_create_gpe_block : GPE 00 to 0F [_GPE] 2 regs on int
0x9
evgpeblk-0957 [00] ev_create_gpe_block : GPE 10 to 1F [_GPE] 2 regs on int
0x9
ACPI: EC: EC description table is found, configuring boot EC
ACPI: EC: non-query interrupt received, switching to interrupt mode
Completing Region/Field/Buffer/Package
initialization:................................................................................................................................................................................................................................
Initialized 18/19 Regions 124/124 Fields 57/57 Buffers 25/25 Packages (1195
nodes)
Initializing Device/Processor/Thermal objects by executing _INI
methods:........
Executed 8 _INI methods requiring 2 _STA executions (examined 61 objects)
evgpeblk-1054 [00] ev_initialize_gpe_bloc: Found 5 Wake, Enabled 0 Runtime GPEs
in this block
evgpeblk-1054 [00] ev_initialize_gpe_bloc: Found 1 Wake, Enabled 0 Runtime GPEs
in this block
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: 0000:00:00.0 reg 10 32bit mmio: [d0000000, dfffffff]
PCI: 0000:00:1d.0 reg 20 io port: [1800, 181f]
PCI: 0000:00:1d.1 reg 20 io port: [1820, 183f]
PCI: 0000:00:1d.2 reg 20 io port: [1840, 185f]
HPET not enabled in BIOS. You might try hpet=force boot option
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH4 GPIO
PCI: 0000:00:1f.1 reg 10 io port: [1f0, 1f7]
PCI: 0000:00:1f.1 reg 14 io port: [3f4, 3f7]
PCI: 0000:00:1f.1 reg 18 io port: [170, 177]
PCI: 0000:00:1f.1 reg 1c io port: [374, 377]
PCI: 0000:00:1f.1 reg 20 io port: [1860, 186f]
PCI: 0000:00:1f.1 reg 24 32bit mmio: [0, 3ff]
PCI: 0000:00:1f.3 reg 20 io port: [1880, 189f]
PCI: 0000:00:1f.5 reg 10 io port: [1c00, 1cff]
PCI: 0000:00:1f.5 reg 14 io port: [18c0, 18ff]
PCI: 0000:01:00.0 reg 10 32bit mmio: [e0000000, e7ffffff]
PCI: 0000:01:00.0 reg 14 io port: [2000, 20ff]
PCI: 0000:01:00.0 reg 18 32bit mmio: [c0100000, c010ffff]
PCI: 0000:01:00.0 reg 30 32bit mmio: [0, 1ffff]
pci 0000:01:00.0: supports D1
pci 0000:01:00.0: supports D2
PCI: bridge 0000:00:01.0 io port: [2000, 2fff]
PCI: bridge 0000:00:01.0 32bit mmio: [c0100000, c01fffff]
PCI: bridge 0000:00:01.0 32bit mmio pref: [e0000000, e7ffffff]
PCI: 0000:02:03.0 reg 10 32bit mmio: [50000000, 50000fff]
pci 0000:02:03.0: supports D1
pci 0000:02:03.0: supports D2
pci 0000:02:03.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:03.0: PME# disabled
PCI: 0000:02:03.1 reg 10 32bit mmio: [50100000, 50100fff]
pci 0000:02:03.1: supports D1
pci 0000:02:03.1: supports D2
pci 0000:02:03.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:03.1: PME# disabled
PCI: 0000:02:05.0 reg 10 32bit mmio: [c0201000, c02010ff]
PCI: 0000:02:05.0 reg 14 io port: [7440, 7447]
PCI: 0000:02:05.0 reg 18 io port: [7000, 70ff]
pci 0000:02:05.0: supports D2
pci 0000:02:05.0: PME# supported from D2 D3hot D3cold
pci 0000:02:05.0: PME# disabled
PCI: 0000:02:08.0 reg 10 32bit mmio: [c0200000, c0200fff]
PCI: 0000:02:08.0 reg 14 io port: [7400, 743f]
pci 0000:02:08.0: supports D1
pci 0000:02:08.0: supports D2
pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:08.0: PME# disabled
pci 0000:00:1e.0: transparent bridge
PCI: bridge 0000:00:1e.0 io port: [3000, 7fff]
PCI: bridge 0000:00:1e.0 32bit mmio: [c0200000, cfffffff]
PCI: bridge 0000:00:1e.0 32bit mmio pref: [e8000000, efffffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 9 10 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 9 10 11) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
AppArmor: AppArmor Filesystem Enabled
ACPI: RTC can wake from S4
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0xc0000-0xc3fff could not be reserved
system 00:00: iomem range 0xc4000-0xc7fff could not be reserved
system 00:00: iomem range 0xc8000-0xcbfff could not be reserved
system 00:00: iomem range 0xcc000-0xcffff could not be reserved
system 00:00: iomem range 0xdc000-0xdffff could not be reserved
system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
system 00:00: iomem range 0xe8000-0xebfff could not be reserved
system 00:00: iomem range 0xec000-0xeffff could not be reserved
system 00:00: iomem range 0xf0000-0xfffff could not be reserved
system 00:00: iomem range 0x100000-0x17ffffff could not be reserved
system 00:00: iomem range 0xfec00000-0xffffffff could not be reserved
system 00:02: ioport range 0x1000-0x107f has been reserved
system 00:02: ioport range 0x1180-0x11bf has been reserved
system 00:02: ioport range 0x15e0-0x15ef has been reserved
system 00:02: ioport range 0x1600-0x167f has been reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0x2000-0x2fff
pci 0000:00:01.0: MEM window: 0xc0100000-0xc01fffff
pci 0000:00:01.0: PREFETCH window: 0x000000e0000000-0x000000e7ffffff
pci 0000:02:03.0: CardBus bridge, secondary bus 0000:03
pci 0000:02:03.0: IO window: 0x003000-0x0030ff
pci 0000:02:03.0: IO window: 0x003400-0x0034ff
pci 0000:02:03.0: PREFETCH window: 0xe8000000-0xebffffff
pci 0000:02:03.0: MEM window: 0xc4000000-0xc7ffffff
pci 0000:02:03.1: CardBus bridge, secondary bus 0000:07
pci 0000:02:03.1: IO window: 0x003800-0x0038ff
pci 0000:02:03.1: IO window: 0x003c00-0x003cff
pci 0000:02:03.1: PREFETCH window: 0xec000000-0xefffffff
pci 0000:02:03.1: MEM window: 0xc8000000-0xcbffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1e.0: IO window: 0x3000-0x7fff
pci 0000:00:1e.0: MEM window: 0xc0200000-0xcfffffff
pci 0000:00:1e.0: PREFETCH window: 0x000000e8000000-0x000000efffffff
pci 0000:00:1e.0: setting latency timer to 64
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
pci 0000:02:03.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
pci 0000:02:03.1: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffffffffffff]
bus: 01 index 0 io port: [2000, 2fff]
bus: 01 index 1 mmio: [c0100000, c01fffff]
bus: 01 index 2 mmio: [e0000000, e7ffffff]
bus: 01 index 3 mmio: [0, 0]
bus: 02 index 0 io port: [3000, 7fff]
bus: 02 index 1 mmio: [c0200000, cfffffff]
bus: 02 index 2 mmio: [e8000000, efffffff]
bus: 02 index 3 io port: [0, ffff]
bus: 02 index 4 mmio: [0, ffffffffffffffff]
bus: 03 index 0 io port: [3000, 30ff]
bus: 03 index 1 io port: [3400, 34ff]
bus: 03 index 2 mmio: [e8000000, ebffffff]
bus: 03 index 3 mmio: [c4000000, c7ffffff]
bus: 07 index 0 io port: [3800, 38ff]
bus: 07 index 1 io port: [3c00, 3cff]
bus: 07 index 2 mmio: [ec000000, efffffff]
bus: 07 index 3 mmio: [c8000000, cbffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 5599k freed
Simple Boot Flag at 0x35 set to 0x1
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
type=2000 audit(1228225389.617:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 184
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
perfmon: added sampling format default
pci 0000:01:00.0: Boot video device
pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
vesafb: framebuffer at 0xe0000000, mapped to 0xd8880000, using 3750k, total
8192k
vesafb: mode is 800x600x16, linelength=1600, pages=7
vesafb: protected mode interface info at c000:5037
vesafb: pmi: set display start = c00c50cb, set palette = c00c5117
vesafb: pmi: ports = 2010 2016 2054 2038 203c 205c 2000 2004 20b0 20b2 20b4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...
bootsplash: silentjpeg size 82170 bytes
bootsplash: ...found (800x600, 31893 bytes, v3).
Console: switching to colour frame buffer device 96x33
Clocksource tsc unstable (delta = -192313717 ns)
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver8 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 328k freed
Write protecting the kernel text: 2424k
Write protecting the kernel read-only data: 1788k
input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input0
ACPI: processor limited to max C-state 1
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [CPU] (supports 8 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THM0] (33 C)
ACPI: ACPI Dock Station Driver: 2 docks/bays found
SCSI subsystem initialized
libata version 3.00 loaded.
ata_piix 0000:00:1f.1: version 2.12
ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ata_piix 0000:00:1f.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1860 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1868 irq 15
ata1: clearing spurious IRQ
ata1.00: ATA-5: HITACHI_DK23DA-30B, 00J1A0B3, max UDMA/100
ata1.00: 58605120 sectors, multi 16: LBA
ata1: clearing spurious IRQ
ata1: clearing spurious IRQ
ata1.00: configured for UDMA/100
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/input/input1
ata2: clearing spurious IRQ
ata2.00: ATAPI: MATSHITADVD-ROM SR-8177, NB21, max UDMA/33
ata2: clearing spurious IRQ
ata2: clearing spurious IRQ
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA HITACHI_DK23DA-3 00J1 PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM MATSHITA DVD-ROM SR-8177 NB21 PQ: 0 ANSI: 5
Uniform Multi-Platform E-IDE driver
BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
EDD information not available.
udevd version 128 started
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
sd 0:0:0:0: [sda] 58605120 512-byte hardware sectors: (30.0GB/27.9GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 0:0:0:0: [sda] 58605120 512-byte hardware sectors: (30.0GB/27.9GiB)
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27.7-4-pae uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1 sda2 < sda5 >
sd 0:0:0:0: [sda] Attached SCSI disk
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27.7-4-pae uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27.7-4-pae uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
udevd version 128 started
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 5
Linux agpgart interface v0.103
intel_rng: FWH not detected
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
iTCO_vendor_support: vendor-support=0
sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
agpgart-intel 0000:00:00.0: Intel 830M Chipset
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
i801_smbus 0000:00:1f.3: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ
11
ACPI: I/O resource 0000:00:1f.3 [0x1880-0x189f] conflicts with ACPI region SBUS
[0x1880-0x188f]
ACPI: Device needs an ACPI driver
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
iTCO_wdt: Found a ICH3-M TCO device (Version=1, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as
/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4
ACPI: Sleep Button (CM) [SLPB]
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
NET: Registered protocol family 23
parport_pc 00:0b: reported by Plug and Play ACPI
parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
Intel ICH 0000:00:1f.5: enabling device (0000 -> 0001)
Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ
11
Intel ICH 0000:00:1f.5: setting latency timer to 64
input: Video Bus as
/devices/LNXSYSTM:00/device:00/PNP0A03:00/device:03/device:04/input/input5
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
nsc-ircc, chip->init
nsc-ircc, Found chip at base=0x02e
nsc-ircc, driver loaded (Dag Brattli)
nsc_ircc_open(), can't get iobase of 0x2f8
nsc-ircc, Found chip at base=0x02e
nsc-ircc, driver loaded (Dag Brattli)
nsc_ircc_open(), can't get iobase of 0x2f8
nsc-ircc 00:0c: disabled
ACPI: AC Adapter [AC] (on-line)
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
input: PC Speaker as /devices/platform/pcspkr/input/input6
intel8x0_measure_ac97_clock: measured 54850 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
e100 0000:02:08.0: PCI INT A -> Link[LNKE] -> GSI 11 (level, low) -> IRQ 11
e100 0000:02:08.0: PME# disabled
e100: eth0: e100_probe: addr 0xc0200000, irq 11, MAC addr 00:d0:59:b6:fc:8b
Yenta: CardBus bridge found at 0000:02:03.0 [1014:0185]
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000410
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff
cs: IO port probe 0x3000-0x7fff: clean.
pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff
Yenta: CardBus bridge found at 0000:02:03.1 [1014:0185]
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff
cs: IO port probe 0x3000-0x7fff: clean.
pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff
nsc-ircc 00:0c: activated
nsc-ircc, chip->init
nsc-ircc, Found chip at base=0x02e
nsc-ircc, driver loaded (Dag Brattli)
nsc-ircc 00:0c: disabled
pccard: PCMCIA card inserted into slot 0
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k
ppdev: user-space parallel port driver
cs: memory probe 0xe8000000-0xefffffff: excluding 0xe8000000-0xefffffff
cs: memory probe 0xc0200000-0xcfffffff: excluding 0xc0200000-0xc11fffff
0xc1a00000-0xc21fffff 0xc2a00000-0xc31fffff 0xc3a00000-0xcc1fffff
0xcca00000-0xcd1fffff 0xcda00000-0xce1fffff 0xcea00000-0xcf1fffff
0xcfa00000-0xd01fffff
pcmcia: registering new device pcmcia0.0
orinoco 0.15 (David Gibson , Pavel Roskin
, et al)
orinoco_cs 0.15 (David Gibson , Pavel Roskin
, et al)
eth1: Hardware identity 0001:0001:0004:0000
eth1: Station identity 001f:0001:0008:0048
eth1: Firmware determined as Lucent/Agere 8.72
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:02:2d:28:e3:6c
eth1: Station name "HERMES I"
eth1: ready
eth1: orinoco_cs at 0.0, irq 3, io 0x3100-0x313f
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
ACPI: Battery Slot [BAT0] (battery present)
Adding 1124508k swap on /dev/sda5. Priority:-1 extents:1 across:1124508k
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised:
dm-devel@redhat.com
loop: module loaded
fuse init (API version 7.9)
type=1505 audit(1228225419.474:2): operation="profile_load" name="/bin/ping"
name2="default" pid=1656
type=1505 audit(1228225419.930:3): operation="profile_load" name="/sbin/klogd"
name2="default" pid=1686
type=1505 audit(1228225420.558:4): operation="profile_load"
name="/sbin/syslog-ng" name2="default" pid=1706
type=1505 audit(1228225421.310:5): operation="profile_load"
name="/sbin/syslogd" name2="default" pid=1734
type=1505 audit(1228225421.838:6): operation="profile_load"
name="/usr/sbin/avahi-daemon" name2="default" pid=1762
type=1505 audit(1228225422.226:7): operation="profile_load"
name="/usr/sbin/identd" name2="default" pid=1772
type=1505 audit(1228225422.646:8): operation="profile_load"
name="/usr/sbin/mdnsd" name2="default" pid=1773
type=1505 audit(1228225423.122:9): operation="profile_load"
name="/usr/sbin/nscd" name2="default" pid=1774
type=1505 audit(1228225423.718:10): operation="profile_load"
name="/usr/sbin/ntpd" name2="default" pid=1776
type=1505 audit(1228225424.102:11): operation="profile_load"
name="/usr/sbin/traceroute" name2="default" pid=1777
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
powernow: This module only works with AMD K7 CPUs
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (6144 buckets, 24576 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
Marking TSC unstable due to cpufreq changes
ttyS1: LSR safety check engaged!
BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
EDD information not available.
ADDRCONF(NETDEV_UP): eth1: link is not ready
eth1: New link status: Connected (0001)
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
NET: Registered protocol family 17
eth1: no IPv6 routers present
SFW2-INext-DROP-DEFLT IN=eth1 OUT=
MAC=01:00:5e:00:00:fb:00:21:e9:e6:c5:98:08:00 SRC=10.183.112.146
DST=224.0.0.251 LEN=222 TOS=0x18 PREC=0x00 TTL=255 ID=40010 PROTO=UDP SPT=5353
DPT=5353 LEN=202
SFW2-INext-DROP-DEFLT IN=eth1 OUT=
MAC=01:00:5e:00:00:fb:00:21:e9:e6:c5:98:08:00 SRC=10.183.112.146
DST=224.0.0.251 LEN=162 TOS=0x18 PREC=0x00 TTL=255 ID=12627 PROTO=UDP SPT=5353
DPT=5353 LEN=142
SFW2-INext-DROP-DEFLT IN=eth1 OUT=
MAC=01:00:5e:00:00:fb:00:21:e9:e6:c5:98:08:00 SRC=10.183.112.146
DST=224.0.0.251 LEN=222 TOS=0x18 PREC=0x00 TTL=255 ID=13863 PROTO=UDP SPT=5353
DPT=5353 LEN=202
SFW2-INext-DROP-DEFLT IN=eth1 OUT=
MAC=01:00:5e:00:00:fb:00:1f:5b:cd:d3:87:08:00 SRC=10.183.114.238
DST=224.0.0.251 LEN=106 TOS=0x18 PREC=0x00 TTL=255 ID=33472 PROTO=UDP SPT=5353
DPT=5353 LEN=86
SFW2-INext-DROP-DEFLT IN=eth1 OUT=
MAC=01:00:5e:00:00:fb:00:1f:5b:cd:d3:87:08:00 SRC=10.183.114.238
DST=224.0.0.251 LEN=106 TOS=0x18 PREC=0x00 TTL=255 ID=49045 PROTO=UDP SPT=5353
DPT=5353 LEN=86
SFW2-INext-DROP-DEFLT IN=eth1 OUT=
MAC=01:00:5e:00:00:fb:00:1f:5b:c4:a5:69:08:00 SRC=10.183.113.26 DST=224.0.0.251
LEN=316 TOS=0x18 PREC=0x00 TTL=255 ID=58919 PROTO=UDP SPT=5353 DPT=5353 LEN=296
--
Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are on the CC list for the bug.