[Bug 1170842] On aarch64, using dracut 050, only one interface gets ifup during the pxe boot first stage
http://bugzilla.suse.com/show_bug.cgi?id=1170842 http://bugzilla.suse.com/show_bug.cgi?id=1170842#c1 Thomas Blume <thomas.blume@suse.com> changed: What |Removed |Added ---------------------------------------------------------------------------- CC| |aplanas@suse.com, | |thomas.blume@suse.com Flags| |needinfo?(aplanas@suse.com) --- Comment #1 from Thomas Blume <thomas.blume@suse.com> --- (In reply to Alberto Planas Dominguez from comment #0)
If not explicitly given at the command line, dracut will only set up one interface and just continue if this is successfull, which is the case here: --> 39.785787] localhost dracut-initqueue[575]: + ip -4 addr add 10.0.3.101/24 broadcast 10.0.3.255 dev enp0s1 [ 39.856029] localhost dracut-initqueue[575]: + route=() [ 39.858205] localhost dracut-initqueue[575]: + local r route [ 39.858205] localhost dracut-initqueue[575]: + '[' -n '' ']' [ 39.858205] localhost dracut-initqueue[575]: + local g [ 39.858205] localhost dracut-initqueue[575]: + '[' -n 10.0.3.101 ']' [ 39.858205] localhost dracut-initqueue[575]: + for g in ${GATEWAYS} [ 39.858205] localhost dracut-initqueue[575]: + ip -4 route add default via 10.0.3.101 dev enp0s1 [ 39.898801] localhost dracut-initqueue[575]: + break [ 39.901409] worker dracut-initqueue[575]: + '[' -n '' ']' [ 39.901409] worker dracut-initqueue[575]: + '[' -n worker ']' [ 39.901409] worker dracut-initqueue[575]: + echo worker [ 39.901409] worker dracut-initqueue[575]: + '[' '!' -s /tmp/net.enp0s1.resolv.conf.ipv4 ']' [ 39.907099] worker dracut-initqueue[575]: + '[' -n '' ']' [ 39.907099] worker dracut-initqueue[575]: + '[' -n '' ']' [ 39.907099] worker dracut-initqueue[575]: + '[' -n 10.0.3.1 ']' [ 39.907099] worker dracut-initqueue[575]: + for s in ${DNSSERVERS} [ 39.907099] worker dracut-initqueue[575]: + echo nameserver 10.0.3.1 [ 39.907099] worker dracut-initqueue[575]: + '[' -e /tmp/net.enp0s1.resolv.conf.ipv4 ']' [ 39.907099] worker dracut-initqueue[575]: + '[' '!' -e /etc/resolv.conf ']' [ 39.907099] worker dracut-initqueue[575]: + cp -f /tmp/net.enp0s1.resolv.conf.ipv4 /etc/resolv.conf [ 39.945505] worker systemd[1]: inotify event for /etc/localtime [ 39.949340] worker systemd[1]: Failed to stat /etc/localtime, ignoring: No such file or directory [ 39.951267] worker dracut-initqueue[575]: + info 'DHCP is finished successfully' [ 39.953333] worker dracut-initqueue[575]: + echo 'DHCP is finished successfully' --< The root cause visible in the logs is that the device for installation isn't found: --> [ 48.582317] worker dracut-pre-mount[719]: /////lib/dracut/hooks/pre-mount/30-kiwi-dump-image.sh@15(report_and_quit): die 'No device(s) for installation found' [ 48.582317] worker dracut-pre-mount[719]: ////lib/dracut-lib.sh@460(die): echo '<24>dracut: FATAL: No device(s) for installation found' [ 48.582317] worker dracut-pre-mount[719]: ////lib/dracut-lib.sh@461(die): echo '<24>dracut: Refusing to continue' [ 48.582317] worker dracut-pre-mount[719]: ////lib/dracut-lib.sh@465(die): echo 'warn dracut: FATAL: "No device(s) for installation found"' [ 48.582317] worker dracut-pre-mount[719]: ////lib/dracut-lib.sh@466(die): echo 'warn dracut: Refusing to continue' --< Still, I can see that a device gets plugged: --> [ 36.297674] localhost systemd[1]: dev-vda.device: Changed dead -> plugged [ 36.298760] localhost systemd[1]: sys-devices-platform-LNRO0005:1f-virtio2-block-vda.device: Changed dead -> plugged --< Is vda the device configured for installation? -- You are receiving this mail because: You are on the CC list for the bug.
participants (1)
-
bugzilla_noreply@novell.com