[Bug 709243] New: Kernel 3.0: ums_eneub6250 is broken
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c0 Summary: Kernel 3.0: ums_eneub6250 is broken Classification: openSUSE Product: openSUSE 11.4 Version: Final Platform: x86-64 OS/Version: openSUSE 11.3 Status: NEW Severity: Major Priority: P5 - None Component: Kernel AssignedTo: kernel-maintainers@forge.provo.novell.com ReportedBy: andihartmann@freenet.de QAContact: qa@suse.de Found By: --- Blocker: --- User-Agent: Mozilla/5.0 (X11; Linux x86_64; rv:5.0) Gecko/20110720 Firefox/5.0 SeaMonkey/2.2 MSI CR620 / card reader, UB6250: The appropriate driver ums_eneub6250 (or keucr?) can't handle SD cards. Just insert a vfat formated sdcard. These messages are print to messages afterwards: Jul 29 14:06:36 notebook2 kernel: [ 836.404459] usb 1-1.1: new high speed USB device number 4 using ehci_hcd Jul 29 14:06:36 notebook2 kernel: [ 836.490876] usb 1-1.1: New USB device found, idVendor=0cf2, idProduct=6250 Jul 29 14:06:36 notebook2 kernel: [ 836.490882] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=4 Jul 29 14:06:36 notebook2 kernel: [ 836.490886] usb 1-1.1: Product: UB6250 Jul 29 14:06:36 notebook2 kernel: [ 836.490889] usb 1-1.1: Manufacturer: ENE Flash Jul 29 14:06:36 notebook2 kernel: [ 836.490892] usb 1-1.1: SerialNumber: 606569746801 Jul 29 14:06:36 notebook2 kernel: [ 836.491421] scsi5 : usb-storage 1-1.1:1.0 Jul 29 14:06:36 notebook2 mtp-probe: checking bus 1, device 4: "/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1" Jul 29 14:06:36 notebook2 mtp-probe: bus: 1, device: 4 was not an MTP device Jul 29 14:06:37 notebook2 kernel: [ 837.493868] scsi scan: INQUIRY result too short (5), using 36 Jul 29 14:06:37 notebook2 kernel: [ 837.493880] scsi 5:0:0:0: Direct-Access PQ: 0 ANSI: 0 Jul 29 14:06:37 notebook2 kernel: [ 837.494256] sd 5:0:0:0: Attached scsi generic sg2 type 0 Jul 29 14:06:37 notebook2 kernel: [ 837.501188] sd 5:0:0:0: [sdb] Sector size 0 reported, assuming 512. Jul 29 14:06:37 notebook2 kernel: [ 837.501199] sd 5:0:0:0: [sdb] 1 512-byte logical blocks: (512 B/512 B) Jul 29 14:06:37 notebook2 kernel: [ 837.501205] sd 5:0:0:0: [sdb] 0-byte physical blocks Jul 29 14:06:37 notebook2 kernel: [ 837.502966] sd 5:0:0:0: [sdb] Write Protect is off Jul 29 14:06:37 notebook2 kernel: [ 837.502969] sd 5:0:0:0: [sdb] Mode Sense: 00 00 00 00 Jul 29 14:06:37 notebook2 kernel: [ 837.504630] sd 5:0:0:0: [sdb] Asking for cache data failed Jul 29 14:06:37 notebook2 kernel: [ 837.504633] sd 5:0:0:0: [sdb] Assuming drive cache: write through Jul 29 14:06:37 notebook2 kernel: [ 837.508171] sd 5:0:0:0: [sdb] Sector size 0 reported, assuming 512. Jul 29 14:06:37 notebook2 kernel: [ 837.511665] sd 5:0:0:0: [sdb] Asking for cache data failed Jul 29 14:06:37 notebook2 kernel: [ 837.511668] sd 5:0:0:0: [sdb] Assuming drive cache: write through Jul 29 14:06:37 notebook2 kernel: [ 837.516668] sd 5:0:0:0: [sdb] Unhandled sense code Jul 29 14:06:37 notebook2 kernel: [ 837.516671] sd 5:0:0:0: [sdb] Result: hostbyte=invalid driverbyte=DRIVER_SENSE Jul 29 14:06:37 notebook2 kernel: [ 837.516675] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] Jul 29 14:06:37 notebook2 kernel: [ 837.516679] sd 5:0:0:0: [sdb] Add. Sense: Recorded entity not found Jul 29 14:06:37 notebook2 kernel: [ 837.516684] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 Jul 29 14:06:37 notebook2 kernel: [ 837.516691] end_request: critical target error, dev sdb, sector 0 Jul 29 14:06:37 notebook2 kernel: [ 837.516694] Buffer I/O error on device sdb, logical block 0 Jul 29 14:06:37 notebook2 kernel: [ 837.521942] sd 5:0:0:0: [sdb] Unhandled sense code Jul 29 14:06:37 notebook2 kernel: [ 837.521946] sd 5:0:0:0: [sdb] Result: hostbyte=invalid driverbyte=DRIVER_SENSE Jul 29 14:06:37 notebook2 kernel: [ 837.521950] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] Jul 29 14:06:37 notebook2 kernel: [ 837.521953] sd 5:0:0:0: [sdb] Add. Sense: Recorded entity not found Jul 29 14:06:37 notebook2 kernel: [ 837.521957] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 Jul 29 14:06:37 notebook2 kernel: [ 837.521964] end_request: critical target error, dev sdb, sector 0 Jul 29 14:06:37 notebook2 kernel: [ 837.521968] Buffer I/O error on device sdb, logical block 0 Jul 29 14:06:37 notebook2 kernel: [ 837.527588] sd 5:0:0:0: [sdb] Unhandled sense code Jul 29 14:06:37 notebook2 kernel: [ 837.527591] sd 5:0:0:0: [sdb] Result: hostbyte=invalid driverbyte=DRIVER_SENSE Jul 29 14:06:37 notebook2 kernel: [ 837.527595] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] Jul 29 14:06:37 notebook2 kernel: [ 837.527599] sd 5:0:0:0: [sdb] Add. Sense: Recorded entity not found Jul 29 14:06:37 notebook2 kernel: [ 837.527603] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 Jul 29 14:06:37 notebook2 kernel: [ 837.527610] end_request: critical target error, dev sdb, sector 0 Jul 29 14:06:37 notebook2 kernel: [ 837.527613] Buffer I/O error on device sdb, logical block 0 Jul 29 14:06:37 notebook2 kernel: [ 837.533423] sd 5:0:0:0: [sdb] Unhandled sense code Jul 29 14:06:37 notebook2 kernel: [ 837.533426] sd 5:0:0:0: [sdb] Result: hostbyte=invalid driverbyte=DRIVER_SENSE Jul 29 14:06:37 notebook2 kernel: [ 837.533430] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] Jul 29 14:06:37 notebook2 kernel: [ 837.533434] sd 5:0:0:0: [sdb] Add. Sense: Recorded entity not found Jul 29 14:06:37 notebook2 kernel: [ 837.533438] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 Jul 29 14:06:37 notebook2 kernel: [ 837.533444] end_request: critical target error, dev sdb, sector 0 Jul 29 14:06:37 notebook2 kernel: [ 837.533448] Buffer I/O error on device sdb, logical block 0 Jul 29 14:06:37 notebook2 kernel: [ 837.533458] ldm_validate_partition_table(): Disk read failed. Jul 29 14:06:37 notebook2 kernel: [ 837.538286] sd 5:0:0:0: [sdb] Unhandled sense code Jul 29 14:06:37 notebook2 kernel: [ 837.538290] sd 5:0:0:0: [sdb] Result: hostbyte=invalid driverbyte=DRIVER_SENSE Jul 29 14:06:37 notebook2 kernel: [ 837.538294] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] Jul 29 14:06:37 notebook2 kernel: [ 837.538298] sd 5:0:0:0: [sdb] Add. Sense: Recorded entity not found Jul 29 14:06:37 notebook2 kernel: [ 837.538303] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 Jul 29 14:06:37 notebook2 kernel: [ 837.538310] end_request: critical target error, dev sdb, sector 0 Jul 29 14:06:37 notebook2 kernel: [ 837.538314] Buffer I/O error on device sdb, logical block 0 Jul 29 14:06:37 notebook2 kernel: [ 837.542917] sd 5:0:0:0: [sdb] Unhandled sense code Jul 29 14:06:37 notebook2 kernel: [ 837.542921] sd 5:0:0:0: [sdb] Result: hostbyte=invalid driverbyte=DRIVER_SENSE Jul 29 14:06:37 notebook2 kernel: [ 837.542924] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] Jul 29 14:06:37 notebook2 kernel: [ 837.542928] sd 5:0:0:0: [sdb] Add. Sense: Recorded entity not found Jul 29 14:06:37 notebook2 kernel: [ 837.542934] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 Jul 29 14:06:37 notebook2 kernel: [ 837.542941] end_request: critical target error, dev sdb, sector 0 Jul 29 14:06:37 notebook2 kernel: [ 837.542945] Buffer I/O error on device sdb, logical block 0 Jul 29 14:06:37 notebook2 kernel: [ 837.548143] sd 5:0:0:0: [sdb] Unhandled sense code Jul 29 14:06:37 notebook2 kernel: [ 837.548146] sd 5:0:0:0: [sdb] Result: hostbyte=invalid driverbyte=DRIVER_SENSE Jul 29 14:06:37 notebook2 kernel: [ 837.548149] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] Jul 29 14:06:37 notebook2 kernel: [ 837.548153] sd 5:0:0:0: [sdb] Add. Sense: Recorded entity not found Jul 29 14:06:37 notebook2 kernel: [ 837.548156] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 Jul 29 14:06:37 notebook2 kernel: [ 837.548164] end_request: critical target error, dev sdb, sector 0 Jul 29 14:06:37 notebook2 kernel: [ 837.548167] Buffer I/O error on device sdb, logical block 0 Jul 29 14:06:37 notebook2 kernel: [ 837.553369] sd 5:0:0:0: [sdb] Unhandled sense code Jul 29 14:06:37 notebook2 kernel: [ 837.553374] sd 5:0:0:0: [sdb] Result: hostbyte=invalid driverbyte=DRIVER_SENSE Jul 29 14:06:37 notebook2 kernel: [ 837.553380] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] Jul 29 14:06:37 notebook2 kernel: [ 837.553395] sd 5:0:0:0: [sdb] Add. Sense: Recorded entity not found Jul 29 14:06:37 notebook2 kernel: [ 837.553401] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 Jul 29 14:06:37 notebook2 kernel: [ 837.553412] end_request: critical target error, dev sdb, sector 0 Jul 29 14:06:37 notebook2 kernel: [ 837.553417] Buffer I/O error on device sdb, logical block 0 Jul 29 14:06:37 notebook2 kernel: [ 837.558289] sd 5:0:0:0: [sdb] Unhandled sense code Jul 29 14:06:37 notebook2 kernel: [ 837.558292] sd 5:0:0:0: [sdb] Result: hostbyte=invalid driverbyte=DRIVER_SENSE Jul 29 14:06:37 notebook2 kernel: [ 837.558294] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] Jul 29 14:06:37 notebook2 kernel: [ 837.558297] sd 5:0:0:0: [sdb] Add. Sense: Recorded entity not found Jul 29 14:06:37 notebook2 kernel: [ 837.558301] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 Jul 29 14:06:37 notebook2 kernel: [ 837.558306] end_request: critical target error, dev sdb, sector 0 Jul 29 14:06:37 notebook2 kernel: [ 837.562829] sd 5:0:0:0: [sdb] Unhandled sense code Jul 29 14:06:37 notebook2 kernel: [ 837.562833] sd 5:0:0:0: [sdb] Result: hostbyte=invalid driverbyte=DRIVER_SENSE Jul 29 14:06:37 notebook2 kernel: [ 837.562835] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] Jul 29 14:06:37 notebook2 kernel: [ 837.562838] sd 5:0:0:0: [sdb] Add. Sense: Recorded entity not found Jul 29 14:06:37 notebook2 kernel: [ 837.562842] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 Jul 29 14:06:37 notebook2 kernel: [ 837.562849] end_request: critical target error, dev sdb, sector 0 Jul 29 14:06:37 notebook2 kernel: [ 837.567718] sd 5:0:0:0: [sdb] Unhandled sense code Jul 29 14:06:37 notebook2 kernel: [ 837.567722] sd 5:0:0:0: [sdb] Result: hostbyte=invalid driverbyte=DRIVER_SENSE Jul 29 14:06:37 notebook2 kernel: [ 837.567725] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] Jul 29 14:06:37 notebook2 kernel: [ 837.567729] sd 5:0:0:0: [sdb] Add. Sense: Recorded entity not found Jul 29 14:06:37 notebook2 kernel: [ 837.567732] sd 5:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 Jul 29 14:06:37 notebook2 kernel: [ 837.567739] end_request: critical target error, dev sdb, sector 0 Jul 29 14:06:37 notebook2 kernel: [ 837.567752] sdb: unable to read partition table Jul 29 14:06:37 notebook2 kernel: [ 837.567755] sdb: partition table beyond EOD, enabling native capacity Jul 29 14:06:37 notebook2 kernel: [ 837.571599] sd 5:0:0:0: [sdb] Unsupported sector size 1463898624. Jul 29 14:06:37 notebook2 kernel: [ 837.571603] sd 5:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B) Jul 29 14:06:37 notebook2 kernel: [ 837.571605] sd 5:0:0:0: [sdb] 1463898624-byte physical blocks Jul 29 14:06:37 notebook2 kernel: [ 837.575280] sd 5:0:0:0: [sdb] Asking for cache data failed Jul 29 14:06:37 notebook2 kernel: [ 837.575284] sd 5:0:0:0: [sdb] Assuming drive cache: write through Jul 29 14:06:37 notebook2 kernel: [ 837.575289] sdb: detected capacity change from 512 to 0 Jul 29 14:06:37 notebook2 kernel: [ 837.581477] sd 5:0:0:0: [sdb] Sector size 0 reported, assuming 512. Jul 29 14:06:37 notebook2 kernel: [ 837.581488] sd 5:0:0:0: [sdb] 1 512-byte logical blocks: (512 B/512 B) Jul 29 14:06:37 notebook2 kernel: [ 837.581490] sd 5:0:0:0: [sdb] 0-byte physical blocks Jul 29 14:06:37 notebook2 kernel: [ 837.587499] sd 5:0:0:0: [sdb] Asking for cache data failed Jul 29 14:06:37 notebook2 kernel: [ 837.587505] sd 5:0:0:0: [sdb] Assuming drive cache: write through Jul 29 14:06:37 notebook2 kernel: [ 837.587510] sd 5:0:0:0: [sdb] Attached SCSI disk Jul 29 14:07:11 notebook2 avahi-daemon[1902]: Registering new address record for 2002:4fde:ba5:2:c0d9:5cb8:a7cc:3e75 on wlan0.*. Jul 29 14:07:14 notebook2 avahi-daemon[1902]: Withdrawing address record for 2002:4fde:ba5:2:cdaf:6b31:2e75:f034 on wlan0. lspci -vv 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 40 Region 0: Memory at f0000000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at e0e0 [size=8] Expansion ROM at <unassigned> [disabled] Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Address: fee0500c Data: 4159 Capabilities: [d0] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a4] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: i915 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f6809000 (64-bit, non-prefetchable) [size=16] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: mei 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) (prog-if 20 [EHCI]) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f6807000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+ Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 42 Region 0: Memory at f6800000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0a00c Data: 4179 Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE- FLReset+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=02 Status: NegoPending- InProgress- Capabilities: [130 v1] Root Complex Link Desc: PortNumber=0f ComponentID=00 EltType=Config Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+ Addr: 00000000fed1c000 Kernel driver in use: HDA Intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: f5400000-f67fffff Prefetchable memory behind bridge: 000000007c600000-000000007c7fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Slot #0, PowerLimit 10.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: Micro-Star International Co., Ltd. Device 1033 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=04, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: f0400000-f2bfffff Prefetchable memory behind bridge: 000000007c400000-000000007c5fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Slot #1, PowerLimit 10.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: Micro-Star International Co., Ltd. Device 1033 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 05) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: f4000000-f53fffff Prefetchable memory behind bridge: 000000007c200000-000000007c3fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Slot #3, PowerLimit 10.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: Gammagraphx, Inc. (or missing ID) Device 0000 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 05) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: f2c00000-f3ffffff Prefetchable memory behind bridge: 000000007c000000-000000007c1fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #6, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Slot #5, PowerLimit 10.000W; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: Micro-Star International Co., Ltd. Device 1033 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) (prog-if 20 [EHCI]) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at f6806000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+ Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=32 Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Subsystem: Micro-Star International Co., Ltd. Device 1033 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=10 <?> 00:1f.2 IDE interface: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA IDE Controller (rev 05) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at e0d0 [size=8] Region 1: I/O ports at e0c0 [size=4] Region 2: I/O ports at e0b0 [size=8] Region 3: I/O ports at e0a0 [size=4] Region 4: I/O ports at e090 [size=16] Region 5: I/O ports at e080 [size=16] Capabilities: [70] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: ata_piix 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 18 Region 0: Memory at f6805000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at e000 [size=32] Kernel driver in use: i801_smbus 00:1f.5 IDE interface: Intel Corporation 5 Series/3400 Series Chipset 2 port SATA IDE Controller (rev 05) (prog-if 85 [Master SecO PriO]) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at e070 [size=8] Region 1: I/O ports at e060 [size=4] Region 2: I/O ports at e050 [size=8] Region 3: I/O ports at e040 [size=4] Region 4: I/O ports at e030 [size=16] Region 5: I/O ports at e020 [size=16] Capabilities: [70] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] PCI Advanced Features AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP- Kernel driver in use: ata_piix 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 0: Memory at f6804000 (64-bit, non-prefetchable) [size=4K] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Kernel driver in use: intel ips 05:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: AzureWave Device 1089 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at f4000000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [60] Express (v2) Legacy Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [140 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Capabilities: [160 v1] Device Serial Number 00-15-17-ff-ff-24-14-12 Capabilities: [170 v1] Power Budgeting <?> Kernel driver in use: ath9k 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 41 Region 0: I/O ports at a000 [size=256] Region 2: Memory at f2c30000 (64-bit, prefetchable) [size=4K] Region 4: Memory at f2c20000 (64-bit, prefetchable) [size=64K] Expansion ROM at f2c00000 [disabled] [size=128K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0f00c Data: 4161 Capabilities: [70] Express (v2) Endpoint, MSI 01 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB Capabilities: [ac] MSI-X: Enable- Count=2 Masked- Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [cc] Vital Product Data Unknown small resource type 00, will not decode more. Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [140 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Capabilities: [160 v1] Device Serial Number 01-00-00-00-ff-ff-00-00 Kernel driver in use: r8169 3f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 3f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Micro-Star International Co., Ltd. Device 1033 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 004: ID 0cf2:6250 ENE Technology, Inc. SD card reader (UB6250) Bus 002 Device 005: ID 08bb:2902 Texas Instruments Japan PCM2902 Audio Codec lsusb -s 4 -v Bus 001 Device 004: ID 0cf2:6250 ENE Technology, Inc. SD card reader (UB6250) Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0cf2 ENE Technology, Inc. idProduct 0x6250 SD card reader (UB6250) bcdDevice 1.00 iManufacturer 1 ENE Flash iProduct 2 UB6250 iSerial 4 606569746801 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 498mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 6 bInterfaceProtocol 80 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) kernel : 3.0.0-4-desktop 64 bit Reproducible: Always Steps to Reproduce: 1. insert a sd card in the slot 2. take a look in /var/log/messages 3. Actual Results: see details Expected Results: The filesystems should be seen and accessible. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c1 --- Comment #1 from Andreas Hartmann <andihartmann@freenet.de> 2011-08-07 14:31:39 UTC --- It works fine with 2.6.38 kernel. Here is a workaround, because nobody seems to be interested to fix the problem: Take the source for the keucr module from 2.6.38 from drivers/staging/keucr. Copy it to another empty directory and create the following Makefile in that directory: ccflags-y := -Idrivers/scsi obj-$(CONFIG_USB_ENESTORAGE) += keucr.o keucr-y := \ sdscsi.o \ usb.o \ scsiglue.o \ transport.o \ init.o \ msscsi.o \ ms.o \ smscsi.o \ smilmain.o \ smilsub.o \ smilecc.o Before you can compile the old keucr module, you have to install kernel-devel, kernel-desktop-devel (if you have a desktop kernel) and may be kernel-source. Go to the directory with the old keucr sources and enter: make -C /lib/modules/`uname -r`/build M=`pwd` as root: make -C /lib/modules/`uname -r`/build M=`pwd` O=/lib/modules/`uname -r`/build modules_install Blacklist ums_eneub6250 in /etc/modprobe.d/99-local.conf: blacklist ums_eneub6250 (if it has already been loaded, remove it with rmmod) depmod -a modinfo keucr filename: /lib/modules/3.0.0-39-desktop/extra/keucr.ko license: GPL description: ENE USB Mass Storage driver for Linux author: Domao srcversion: 3AB5BAF0CE33E40884509F8 alias: usb:v0CF2p6250d*dc*dsc*dp*ic*isc*ip* alias: usb:v0CF2p6230d*dc*dsc*dp*ic*isc*ip* alias: usb:v058Fp6366d*dc*dsc*dp*ic*isc*ip* depends: vermagic: 3.0.0-39-desktop SMP preempt mod_unload modversions -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c2 Andreas Hartmann <andihartmann@freenet.de> changed: What |Removed |Added ---------------------------------------------------------------------------- CC| |andihartmann@freenet.de, | |jlee@novell.com --- Comment #2 from Andreas Hartmann <andihartmann@freenet.de> 2011-08-08 08:35:44 UTC --- Hi Joey, could you please track this bug or provide a hardware for the kernel developers as it seems to be not that easy without the hardware. See http://permalink.gmane.org/gmane.linux.kernel/1176408 Thank you, Andreas -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c3 Joey Lee <jlee@novell.com> changed: What |Removed |Added ---------------------------------------------------------------------------- AssignedTo|kernel-maintainers@forge.pr |acho@novell.com |ovo.novell.com | --- Comment #3 from Joey Lee <jlee@novell.com> 2011-08-09 01:48:49 UTC --- Our machine send back to MSI. Assign this issue to Al Cho. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c4 Al Cho <acho@novell.com> changed: What |Removed |Added ---------------------------------------------------------------------------- Status|NEW |NEEDINFO CC| |acho@novell.com InfoProvider| |andihartmann@freenet.de --- Comment #4 from Al Cho <acho@novell.com> 2011-08-09 03:53:02 UTC --- (In reply to comment #2)
Hi Joey,
could you please track this bug or provide a hardware for the kernel developers as it seems to be not that easy without the hardware. See
http://permalink.gmane.org/gmane.linux.kernel/1176408
Thank you, Andreas
Hi Andreas, Do you have used ums_eneub6250 with ene-cardreader firmware? I got these firmware license and pushed the patch to dwmw2@infradead.org, and this patch accepted at 29 Jul. You can got from http://git.kernel.org/?p=linux/kernel/git/dwmw2/linux-firmware.git;a=tree May you kindly try it at first? Please let me know if there are problems. Thanks, AL -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c5 Andreas Hartmann <andihartmann@freenet.de> changed: What |Removed |Added ---------------------------------------------------------------------------- Status|NEEDINFO |NEW InfoProvider|andihartmann@freenet.de | --- Comment #5 from Andreas Hartmann <andihartmann@freenet.de> 2011-08-09 06:13:17 UTC --- Hello Al, I tried it yesterday (btw, these files are missing in the firmware package from openSUSE tumbleweed e.g.). I could see from the sourcecode, that the module should load some of these firmware files: ls -l /lib/firmware/ene-ub6250/ insgesamt 24 -rw-r--r-- 1 root root 2048 8. Aug 20:41 ene-ub6250_ms_init.bin -rw-r--r-- 1 root root 2048 8. Aug 20:42 ene-ub6250_msp_rdwr.bin -rw-r--r-- 1 root root 2048 8. Aug 20:41 ene-ub6250_ms_rdwr.bin -rw-r--r-- 1 root root 2048 8. Aug 20:42 ene-ub6250_sd_init1.bin -rw-r--r-- 1 root root 2048 8. Aug 20:43 ene-ub6250_sd_init2.bin -rw-r--r-- 1 root root 2048 8. Aug 20:43 ene-ub6250_sd_rdwr.bin - but they are never loaded. In function ene_load_bincode, a errormessage is thrown, if the firmware file cannot be loaded - but I didn't get any error as I tested without the firmware files. With firmware files, the problem stays the same - because the firmware didn't get loaded at all (seems to be so). I will help you to fix that problem. If you have a patch or something to test, I will try to do it. But I would be glad, if you could isolate the module (or the modules in drivers/usb/storage) for compilation (if it's possible). Thank you, Andreas -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c6 --- Comment #6 from Al Cho <acho@novell.com> 2011-08-10 03:09:48 UTC --- Hi Andreas, I get a MSI u135 (with ene cardreader 6250) and I compiler the linux kernel - (3.1.0-rc1), use the latest linux-firmware (from dwmw2) , then ene cardreader work is fine. Then I read your comment again,and I guess the problem is named fail of your ene cardreader firmware. Would you please re-name those firmware and try the test again? ene-ub6250_ms_init.bin -> ms_init.bin ene-ub6250_msp_rdwr.bin -> msp_rdwr.bin ene-ub6250_ms_rdwr.bin -> ms_rdwr.bin ene-ub6250_sd_init1.bin -> sd_init1.bin ene-ub6250_sd_init2.bin -> sd_init2.bin ene-ub6250_sd_rdwr.bin -> sd_rdwr.bin Thanks, AL -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c7 Andreas Hartmann <andihartmann@freenet.de> changed: What |Removed |Added ---------------------------------------------------------------------------- Status|NEW |RESOLVED Resolution| |FIXED --- Comment #7 from Andreas Hartmann <andihartmann@freenet.de> 2011-08-10 05:57:19 UTC --- Hello Al, thank you very much for your help. It escaped my notice, that git prefixed the directory name to the firmware files :-( . I should have seen this, first and foremost because I saw the correct files in the source ... . Aug 10 07:13:38 pc kernel: [12179.764648] usb 1-1.1: new high speed USB device number 3 using ehci_hcd Aug 10 07:13:38 pc kernel: [12179.850933] usb 1-1.1: New USB device found, idVendor=0cf2, idProduct=6250 Aug 10 07:13:38 pc kernel: [12179.850941] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=4 Aug 10 07:13:38 pc kernel: [12179.850947] usb 1-1.1: Product: UB6250 Aug 10 07:13:38 pc kernel: [12179.850951] usb 1-1.1: Manufacturer: ENE Flash Aug 10 07:13:38 pc kernel: [12179.850955] usb 1-1.1: SerialNumber: 606569746801 Aug 10 07:13:38 pc mtp-probe: checking bus 1, device 3: "/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1" Aug 10 07:13:38 pc mtp-probe: bus: 1, device: 3 was not an MTP device Aug 10 07:13:38 pc kernel: [12179.926238] scsi6 : usb-storage 1-1.1:1.0 Aug 10 07:13:38 pc kernel: [12179.926937] usbcore: registered new interface driver ums_eneub6250 Aug 10 07:13:39 pc kernel: [12181.210065] scsi scan: INQUIRY result too short (5), using 36 Aug 10 07:13:39 pc kernel: [12181.210076] scsi 6:0:0:0: Direct-Access PQ: 0 ANSI: 0 Aug 10 07:13:39 pc kernel: [12181.210416] sd 6:0:0:0: Attached scsi generic sg2 type 0 Aug 10 07:13:39 pc kernel: [12181.210794] sd 6:0:0:0: [sdb] 3985408 512-byte logical blocks: (2.04 GB/1.90 GiB) Aug 10 07:13:39 pc kernel: [12181.210831] sd 6:0:0:0: [sdb] Write Protect is on Aug 10 07:13:39 pc kernel: [12181.210837] sd 6:0:0:0: [sdb] Mode Sense: 0b 00 80 08 Aug 10 07:13:39 pc kernel: [12181.210867] sd 6:0:0:0: [sdb] No Caching mode page present Aug 10 07:13:39 pc kernel: [12181.210886] sd 6:0:0:0: [sdb] Assuming drive cache: write through Aug 10 07:13:39 pc kernel: [12181.211205] sd 6:0:0:0: [sdb] No Caching mode page present Aug 10 07:13:39 pc kernel: [12181.211222] sd 6:0:0:0: [sdb] Assuming drive cache: write through Aug 10 07:13:39 pc kernel: [12181.224407] sdb: sdb1 Aug 10 07:13:39 pc kernel: [12181.224685] sd 6:0:0:0: [sdb] No Caching mode page present Aug 10 07:13:39 pc kernel: [12181.224701] sd 6:0:0:0: [sdb] Assuming drive cache: write through Aug 10 07:13:39 pc kernel: [12181.224709] sd 6:0:0:0: [sdb] Attached SCSI disk Aug 10 07:13:50 pc kernel: [12192.016836] REISERFS (device sdb1): found reiserfs format "3.6" with standard journal Aug 10 07:13:50 pc kernel: [12192.016868] REISERFS (device sdb1): using ordered data mode Aug 10 07:13:50 pc kernel: [12192.016871] reiserfs: using flush barriers Aug 10 07:13:50 pc kernel: [12192.018090] REISERFS (device sdb1): journal params: device sdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 Aug 10 07:13:50 pc kernel: [12192.018414] REISERFS (device sdb1): checking transaction log (sdb1) Aug 10 07:13:50 pc kernel: [12192.022040] REISERFS (device sdb1): Using r5 hash to sort names However, I do have some wish: Please report to messages, that you loaded a firmware file (which file) respectively which file couldn't be loaded at all. It would have reduced the overhead for me and for you :-) Another wish would be, to not replace a driver, which is working by a driver, which isn't ready for use at all. The SD-functionality of keucr was removed in 2.6.39, which was released in May 2011, the firmware for the new driver came 11 days ago (from today). Kind regards, Andreas -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c8 Andreas Hartmann <andihartmann@freenet.de> changed: What |Removed |Added ---------------------------------------------------------------------------- Status|RESOLVED |REOPENED Component|Kernel |Kernel Resolution|FIXED | AssignedTo|acho@suse.com |kernel-maintainers@forge.pr | |ovo.novell.com Product|openSUSE 11.4 |openSUSE 12.1 Target Milestone|--- |Final OS/Version|openSUSE 11.3 |SuSE Other --- Comment #8 from Andreas Hartmann <andihartmann@freenet.de> 2011-12-05 14:35:58 UTC --- Unfortunately, I have to reopen this bug. On openSUSE 12.1, the module doesn't work as expected: Dec 5 14:50:54 notebook2 kernel: [ 285.879168] usb 1-1.1: new high speed USB device number 3 using ehci_hcd Dec 5 14:50:54 notebook2 kernel: [ 285.965482] usb 1-1.1: New USB device found, idVendor=0cf2, idProduct=6250 Dec 5 14:50:54 notebook2 kernel: [ 285.965488] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=4 Dec 5 14:50:54 notebook2 kernel: [ 285.965493] usb 1-1.1: Product: UB6250 Dec 5 14:50:54 notebook2 kernel: [ 285.965496] usb 1-1.1: Manufacturer: ENE Flash Dec 5 14:50:54 notebook2 kernel: [ 285.965498] usb 1-1.1: SerialNumber: 606569746801 Dec 5 14:50:54 notebook2 kernel: [ 286.329518] scsi6 : usb-storage 1-1.1:1.0 Dec 5 14:50:54 notebook2 kernel: [ 286.330040] usbcore: registered new interface driver ums_eneub6250 Dec 5 14:50:54 notebook2 kernel: [ 286.346387] keucr: module is from the staging directory, the quality is unknown, you have been warned. Dec 5 14:50:54 notebook2 kernel: [ 286.347096] usb --- usb_stor_init start Dec 5 14:50:54 notebook2 kernel: [ 286.347124] usbcore: registered new interface driver eucr Dec 5 14:50:54 notebook2 kernel: [ 286.347126] ENE USB Mass Storage support registered. Dec 5 14:50:54 notebook2 dbus-daemon[1133]: **** scsi_host ADDING /sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.0/host6/scsi_host/host6 Dec 5 14:50:54 notebook2 dbus-daemon[1133]: **** scsi_host IGNORING ADD /sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.0/host6/scsi_host/host6 Dec 5 14:50:56 notebook2 kernel: [ 287.692122] scsi 6:0:0:0: Direct-Access-RBC /../../. ./../bus/usb/dri vers PQ: 1 ANSI: 7 Dec 5 14:50:56 notebook2 kernel: [ 287.692391] scsi 6:0:0:0: Attached scsi generic sg2 type 14 Dec 5 14:50:56 notebook2 kernel: [ 287.692545] scsi: On host 6 channel 0 id 0 only 511 (max_scsi_report_luns) of 10233581 luns reported, try increasing max_scsi_report_luns. Dec 5 14:50:56 notebook2 kernel: [ 287.692552] scsi: host 6 channel 0 id 0 lun 0x0fe1376f0088ffff has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692563] scsi: host 6 channel 0 id 0 lun 0x77e1376f0088ffff has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692574] scsi: host 6 channel 0 id 0 lun 0x85e1376f0088ffff has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692584] scsi: host 6 channel 0 id 0 lun 0x8fe1376f0088ffff has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692594] scsi: host 6 channel 0 id 0 lun 0x97e1376f0088ffff has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692606] scsi: host 6 channel 0 id 0 lun 0xabe1376f0088ffff has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692623] scsi: host 6 channel 0 id 0 lun 0x0700000041435449 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692634] scsi: host 6 channel 0 id 0 lun 0x4f4e3d6164640044 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692645] scsi: host 6 channel 0 id 0 lun 0x4556504154483d2f has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692655] scsi: host 6 channel 0 id 0 lun 0x646576696365732f has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692667] scsi: host 6 channel 0 id 0 lun 0x706369303030303a has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692678] scsi: host 6 channel 0 id 0 lun 0x30302f303030303a has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692689] scsi: host 6 channel 0 id 0 lun 0x30303a31612e302f has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692701] scsi: host 6 channel 0 id 0 lun 0x757362312f312d31 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692713] scsi: host 6 channel 0 id 0 lun 0x2f312d312e312f31 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692724] scsi: host 6 channel 0 id 0 lun 0x2d312e313a312e30 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692736] scsi: host 6 channel 0 id 0 lun 0x2f686f7374362f74 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692748] scsi: host 6 channel 0 id 0 lun 0x6172676574363a30 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692760] scsi: host 6 channel 0 id 0 lun 0x3a302f363a303a30 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692772] scsi: host 6 channel 0 id 0 lun 0x3a302f6273672f36 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692802] scsi: host 6 channel 0 id 0 lun 0x3a303a303a300053 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692821] scsi: host 6 channel 0 id 0 lun 0x554253595354454d has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692849] scsi: host 6 channel 0 id 0 lun 0x3d627367004d414a has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692876] scsi: host 6 channel 0 id 0 lun 0x4f523d323533004d has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692903] scsi: host 6 channel 0 id 0 lun 0x494e4f523d320044 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692929] scsi: host 6 channel 0 id 0 lun 0x45564e414d453d62 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692956] scsi: host 6 channel 0 id 0 lun 0x73672f363a303a30 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.692982] scsi: host 6 channel 0 id 0 lun 0x3a30005345514e55 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.693010] scsi: host 6 channel 0 id 0 lun 0x4d3d313935330000 has a LUN larger than currently supported. Dec 5 14:50:56 notebook2 kernel: [ 287.693089] scsi: host 6 channel 0 id 0 lun 0x00000000b3000000 has a LUN larger than currently supported. I had to rebuild the old keucr module from 2.6.38 to get the card reader working again with sd cards. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c Greg Kroah-Hartman <gregkh@suse.com> changed: What |Removed |Added ---------------------------------------------------------------------------- AssignedTo|kernel-maintainers@forge.pr |acho@suse.com |ovo.novell.com | -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c9 Andreas Hartmann <andihartmann@freenet.de> changed: What |Removed |Added ---------------------------------------------------------------------------- Component|Kernel |Kernel AssignedTo|acho@suse.com |kernel-maintainers@forge.pr | |ovo.novell.com Product|openSUSE 12.1 |openSUSE 12.3 --- Comment #9 from Andreas Hartmann <andihartmann@freenet.de> 2013-05-25 08:32:23 UTC --- Ok, it's broken, too, for openSUSE 12.3 (which doesn't mean it would have been working in 12.2 - I just didn't use 12.2). Here is a patched original keucr source (tested with linux 3.9, but most probably works too with 3.7), which makes the device working again. You can compile it with the make-command, which is part of the attached tar.xz file. After compiling, you can install it with ./make modules_install. Afterwards you have to issue depmod -a and you have to "blacklist ums_eneub6250" in /etc/modprobe.d/99-local.conf. Verify with modinfo keucr that the new keucr module is used and not the reduced one delivered with the kernel: modinfo keucr filename: /lib/modules/3.9.3-2.g06ad9d8-desktop/extra/keucr.ko license: GPL description: ENE USB Mass Storage driver for Linux author: Domao srcversion: A663ED5858DE5D7CE808147 alias: usb:v0CF2p6250d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF2p6230d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v058Fp6366d*dc*dsc*dp*ic*isc*ip*in* depends: vermagic: 3.9.3-2.g06ad9d8-desktop SMP preempt mod_unload modversions -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c10 --- Comment #10 from Andreas Hartmann <andihartmann@freenet.de> 2013-05-25 08:34:43 UTC --- Created an attachment (id=541233) --> (http://bugzilla.novell.com/attachment.cgi?id=541233) Source of the original keucr module patched for kernel 3.9 -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c Jeff Mahoney <jeffm@suse.com> changed: What |Removed |Added ---------------------------------------------------------------------------- AssignedTo|kernel-maintainers@forge.pr |oneukum@suse.com |ovo.novell.com | -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c11 Oliver Neukum <oneukum@suse.com> changed: What |Removed |Added ---------------------------------------------------------------------------- Status|REOPENED |NEEDINFO InfoProvider| |acho@suse.com --- Comment #11 from Oliver Neukum <oneukum@suse.com> 2013-09-10 13:45:30 UTC --- Al, do you have a test device? -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=709243 https://bugzilla.novell.com/show_bug.cgi?id=709243#c12 Al Cho <acho@suse.com> changed: What |Removed |Added ---------------------------------------------------------------------------- Status|NEEDINFO |REOPENED InfoProvider|acho@suse.com | --- Comment #12 from Al Cho <acho@suse.com> 2013-09-11 04:18:28 UTC --- No, I don't have it. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
participants (1)
-
bugzilla_noreply＠novell.com