[Bug 350993] New: Unable to get a functional bootsplash with either splashy or bootsplash on PPC .
https://bugzilla.novell.com/show_bug.cgi?id=350993 User hammett@orcon.net.nz added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c1 Summary: Unable to get a functional bootsplash with either splashy or bootsplash on PPC. Product: openSUSE 10.3 Version: Final Platform: PowerPC OS/Version: openSUSE 10.3 Status: NEW Severity: Normal Priority: P5 - None Component: Kernel AssignedTo: kernel-maintainers@forge.provo.novell.com ReportedBy: hammett@orcon.net.nz QAContact: qa@suse.de Found By: Component Test A fresh installation of opensuse 10.3 PPC does not show a bootsplash on an imac b/w g3. Our testers have tried many methods to get the bootsplash functional, but as yet, no luck. We can't find anything wrong in the boot logs, and as far as we can tell bootsplash is being run, just no splash. We have tested uninstalling bootsplash and trying splashy, but splashy isnt even being started. Our splashy tests show that it is working, but won't fire up at boot. We have xubuntu 7.10 on another machine, and using usplash, has a functional bootsplash. I have attached as much info as possible to see if anyone can help. These are clients new to the world of Linux who are switching all their old g3's to opensuse and SLED at a later date. Regards Buttons: --boot ##Y2support-/tmp/siga/siga.txt: 1. Hardware ------------------------------------------------------------------------------- 1.1 procinfo - /usr/bin/procinfo Linux 2.6.22.13-0.3-default (geeko@buildhost) (gcc 4.2.1) #1 1CPU [imacg3.] Memory: Total Used Free Shared Buffers Mem: 189364 187036 2328 0 3700 Swap: 377516 42500 335016 Bootup: Mon Dec 31 07:37:24 2007 Load average: 1.25 1.40 1.10 1/184 3875 user : 0:06:12.40 10.2% page in : 296120 disk 1: 14441r 5164w nice : 0:00:23.21 0.6% page out: 136824 disk 2: 1057r 1928w system: 0:00:49.45 1.4% page act: 51344 IOwait: 0:02:01.43 3.3% page dea: 36421 disk 4: 30r 0w hw irq: 0:00:01.28 0.0% page flt: 1016428 sw irq: 0:00:01.70 0.0% swap in : 2083 idle : 0:51:14.15 84.4% swap out: 10935 uptime: 1:00:43.66 context : 511226 irq 18: 14 Edge MESH irq 31: 4627 Edge ADB irq 20: 0 Level NMI - XMON irq 32: 10954 Edge ide0 irq 25: 3616 Level aic7xxx irq 34: 2065 Edge BMAC-txdma irq 26: 19617 Level libata irq 35: 1943 Edge BMAC-rxdma irq 28: 23389 Level ohci_hcd:us irq 42: 4002 Edge BMAC-misc ------------------------------------------------------------------------------- 1.2 cmdline - /proc/cmdline root=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 quiet splash ------------------------------------------------------------------------------- 1.3 Hardisk ------------------------------------------------------------------------------- 1.3 partitions - /sbin/fdisk -l There is a valid Mac label on this disk. Unfortunately fdisk(1) cannot handle these disks. Use either pdisk or parted to modify the partition table. Nevertheless some advice: 1. fdisk will destroy its contents on write. 2. Be sure that this disk is NOT a still vital part of a volume group. (Otherwise you may erase the other disks as well, if unmirrored.) Disk /dev/sda: 4311 MB, 4311982080 bytes 255 heads, 63 sectors/track, 524 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System There is a valid Mac label on this disk. Unfortunately fdisk(1) cannot handle these disks. Use either pdisk or parted to modify the partition table. Nevertheless some advice: 1. fdisk will destroy its contents on write. 2. Be sure that this disk is NOT a still vital part of a volume group. (Otherwise you may erase the other disks as well, if unmirrored.) Disk /dev/sdb: 4551 MB, 4551129088 bytes 141 heads, 62 sectors/track, 1016 cylinders Units = cylinders of 8742 * 512 = 4475904 bytes Device Boot Start End Blocks Id System ------------------------------------------------------------------------------- 1.4 Mountpoints - /proc/mounts rootfs / rootfs rw 0 0 udev /dev tmpfs rw 0 0 /dev/sda4 / ext3 rw,data=ordered 0 0 proc /proc proc rw 0 0 sysfs /sys sysfs rw 0 0 debugfs /sys/kernel/debug debugfs rw 0 0 devpts /dev/pts devpts rw 0 0 /dev/sdb2 /home ext3 rw,nosuid,nodev,noexec,data=ordered 0 0 securityfs /sys/kernel/security securityfs rw 0 0 /dev/hda /media/SU1030.001 iso9660 ro,nosuid,nodev,noatime 0 0 ------------------------------------------------------------------------------- 1.5 boot_dir - /bin/ls -la /boot total 9916 drwxr-xr-x 2 root root 4096 Dec 30 20:52 . drwxr-xr-x 21 root root 4096 Dec 31 07:37 .. -rw-r--r-- 1 root root 887586 Nov 27 04:42 System.map-2.6.22.13-0.3-default -rw-r--r-- 1 root root 62471 Nov 27 04:45 config-2.6.22.13-0.3-default lrwxrwxrwx 1 root root 28 Dec 30 20:52 initrd -> initrd-2.6.22.13-0.3-default -rw-r--r-- 1 root root 2666721 Dec 30 20:52 initrd-2.6.22.13-0.3-default -rw-r--r-- 1 root root 121181 Nov 27 04:47 symsets-2.6.22.13-0.3-default.tar.gz -rw-r--r-- 1 root root 320289 Nov 27 04:47 symtypes-2.6.22.13-0.3-default.gz -rw-r--r-- 1 root root 93370 Nov 27 04:46 symvers-2.6.22.13-0.3-default.gz lrwxrwxrwx 1 root root 29 Dec 26 22:17 vmlinux -> vmlinux-2.6.22.13-0.3-default -rw-r--r-- 1 root root 5940109 Nov 27 04:45 vmlinux-2.6.22.13-0.3-default ------------------------------------------------------------------------------- 1.6 Kernel - /etc/sysconfig/kernel INITRD_MODULES="pata_cmd64x aic7xxx mesh" DOMU_INITRD_MODULES="xennet xenblk" MODULES_LOADED_ON_BOOT="" ACPI_DSDT="" SCHED_MINTIMESLICE="" SCHED_MAXTIMESLICE="" SKIP_RUNNING_KERNEL="" ------------------------------------------------------------------------------- 1.7 fstab - /etc/fstab /dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 / ext3 acl,user_xattr 1 1 /dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part3 swap swap defaults 0 0 proc /proc proc defaults 0 0 sysfs /sys sysfs noauto 0 0 debugfs /sys/kernel/debug debugfs noauto 0 0 devpts /dev/pts devpts mode=0620,gid=5 0 0 /dev/disk/by-id/scsi-SSEAGATE_ST34520N_AYU38683-part2 /home ext3 user,acl,user_xattr 1 2 ------------------------------------------------------------------------------- 1.8 hwinfo-disk - /usr/sbin/hwinfo --disk 13: IDE 00.0: 10600 Disk [Created at block.233] UDI: /org/freedesktop/Hal/devices/storage_serial_SATA_SAMSUNG_SV0432A0093J1CK403529 Unique ID: WmB0.St6ReAQ8ZZ2 Parent ID: j+MN.yKFryAhlHV9 SysFS ID: /block/sda SysFS BusID: 0:0:0:0 SysFS Device Link: /devices/pci0000:00/0000:00:0d.0/0000:01:01.0/host0/target0:0:0/0:0:0:0 Hardware Class: disk Model: "SAMSUNG SV0432A" Vendor: "SAMSUNG" Device: "SV0432A" Revision: "KH10" Serial ID: "0093J1CK403529" Driver: "pata_cmd64x", "sd" Driver Modules: "pata_cmd64x" Device File: /dev/sda Device Files: /dev/sda, /dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529, /dev/disk/by-id/ata-SAMSUNG_SV0432A_0093J1CK403529, /dev/disk/by-path/pci-0000:01:01.0-scsi-0:0:0:0 Device Number: block 8:0-8:15 Geometry (Logical): CHS 524/255/63 Size: 8421840 sectors a 512 bytes Config Status: cfg=no, avail=yes, need=no, active=unknown Attached to: #7 (IDE interface) 14: SCSI 200.0: 10600 Disk [Created at block.233] UDI: /org/freedesktop/Hal/devices/storage_serial_SSEAGATE_ST34520N_AYU38683 Unique ID: TGKD.+X1yG9OIXC4 Parent ID: fCTE.WcoZRDyx1x7 SysFS ID: /block/sdb SysFS BusID: 2:0:0:0 SysFS Device Link: /devices/pci0000:00/0000:00:0d.0/0000:01:04.0/host2/target2:0:0/2:0:0:0 Hardware Class: disk Model: "SEAGATE ST34520N" Vendor: "SEAGATE" Device: "ST34520N" Revision: "1498" Serial ID: "AYU38683" Driver: "aic7xxx", "sd" Driver Modules: "aic7xxx" Device File: /dev/sdb (/dev/sg1) Device Files: /dev/sdb, /dev/disk/by-id/scsi-SSEAGATE_ST34520N_AYU38683, /dev/disk/by-path/pci-0000:01:04.0-scsi-0:0:0:0 Device Number: block 8:16-8:31 (char 21:1) Geometry (Logical): CHS 1016/141/62 Size: 8888924 sectors a 512 bytes Config Status: cfg=no, avail=yes, need=no, active=unknown Attached to: #8 (SCSI storage controller) ------------------------------------------------------------------------------- 1.9 boot.msg - /var/log/boot.msg Inspecting /boot/System.map-2.6.22.13-0.3-default Loaded 27969 symbols from /boot/System.map-2.6.22.13-0.3-default. Symbols match kernel version 2.6.22. No module symbols loaded - kernel modules not enabled. klogd 1.4.1, log source = ksyslog started. Using PowerMac machine description Total memory = 192MB; using 512kB for hash table (at cbf80000) Linux version 2.6.22.13-0.3-default (geeko@buildhost) (gcc version 4.2.1 (SUSE Linux)) #1 2007/11/19 15:02:58 UTC Found initrd at 0xc4100000:0xc438c000 Found a Paddington mac-io controller, rev: 0, mapped at 0xfdf80000 PowerMac motherboard: Blue&White G3 Entering add_active_range(0, 0, 49152) 0 entries of 256 used Found Grackle (MPC106) PCI host bridge at 0x0000000080000000. Firmware bus number: 0->1 nvram: OF partition at 0x140 nvram: XP partition at 0xffffffff nvram: NR partition at 0xffffffff Top of RAM: 0xc000000, Total RAM: 0xc000000 Memory hole size: 0MB Zone PFN ranges: DMA 0 -> 49152 Normal 49152 -> 49152 HighMem 49152 -> 49152 early_node_map[1] active PFN ranges 0: 0 -> 49152 On node 0 totalpages: 49152 DMA zone: 384 pages used for memmap DMA zone: 0 pages reserved DMA zone: 48768 pages, LIFO batch:15 Normal zone: 0 pages used for memmap HighMem zone: 0 pages used for memmap Built 1 zonelists. Total pages: 48768 Kernel command line: root=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 quiet splash irq: Found primary Apple PIC /pci@80000000/pci-bridge@d/mac-io@5 for 64 irqs irq: System has 64 possible interrupts PID hash table entries: 1024 (order: 10, 4096 bytes) GMT Delta read from XPRAM: 0 minutes, DST: on time_init: decrementer frequency = 24.934450 MHz time_init: processor frequency = 350.000000 MHz Console: colour dummy device 80x25 console handover: boot [udbg0] -> real [tty0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) High memory: 0k Memory: 186232k/196608k available (4388k kernel code, 10060k reserved, 164k data, 467k bss, 208k init) Calibrating delay loop... 49.79 BogoMIPS (lpj=99584) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 device-tree: Duplicate name in /cpus/PowerPC,750@0, renamed to "l2-cache#1" NET: Registered protocol family 16 PCI: Probing PCI hardware PCI: Enabling device 0000:01:04.0 (0014 -> 0017) Registering pmac pic with sysfs... usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered Unpacking initramfs... done Freeing initrd memory: 2608k freed Thermal assist unit using timers, shrink_timer: 500 jiffies audit: initializing netlink socket (disabled) audit(1199039845.656:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Enabling device 0000:00:10.0 (0086 -> 0087) aty128fb: Found Open Firmware ROM Image aty128fb: BIOS not located, guessing timings. aty128fb: Rage128 RE PCI [chip rev 0x2] 16M 128-bit SDR SGRAM (1:1) Console: switching to colour frame buffer device 128x48 fb0: ATY Rage128 frame buffer device on Rage128 RE PCI Generic RTC Driver v1.07 Macintosh non-volatile memory driver v1.1 pmac_zilog: 0.6 (Benjamin Herrenschmidt ) ttyS0 at MMIO 0x80813020 (irq = 16) is a Z85c30 ESCC - Serial port ttyS1 at MMIO 0x80813000 (irq = 17) is a Z85c30 ESCC - Infrared port Serial: MPC52xx PSC UART driver MacIO PCI driver attached to Paddington chipset Can't request resource 0 for MacIO device 0.00000000:power-mg input: Macintosh mouse button emulation as /class/input/input0 Macintosh CUDA driver v0.5 for Unified ADB. apm_emu: PMU APM Emulation initialized. adb: starting probe task... Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx adb devices: adb: finished probe task... ide0: Found Apple Heathrow ATA controller, bus ID 0, irq 32 Probing IDE interface ide0... hda: MATSHITADVD-ROM SR-8583, ATAPI CD/DVD-ROM drive hdb: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive hda: Enabling MultiWord DMA 2 ide0 at 0xcd012000-0xcd012007,0xcd012160 on irq 32 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ohci_hcd 0000:01:06.0: OHCI Host Controller ohci_hcd 0000:01:06.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:01:06.0: irq 28, io mem 0x80880000 usb usb1: new device found, idVendor=0000, idProduct=0000 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: OHCI Host Controller usb usb1: Manufacturer: Linux 2.6.22.13-0.3-default ohci_hcd usb usb1: SerialNumber: 0000:01:06.0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected mice: PS/2 mouse device common for all mice usb 1-2: new full speed USB device using ohci_hcd and address 2 usb 1-2: new device found, idVendor=0409, idProduct=55ab usb 1-2: new device strings: Mfr=0, Product=0, SerialNumber=0 usb 1-2: configuration #1 chosen from 1 choice hub 1-2:1.0: USB hub found hub 1-2:1.0: 4 ports detected usb 1-2.1: new low speed USB device using ohci_hcd and address 3 usb 1-2.1: new device found, idVendor=05ac, idProduct=0201 usb 1-2.1: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-2.1: Product: M2452 usb 1-2.1: Manufacturer: Alps Electric usb 1-2.1: configuration #1 chosen from 1 choice usb 1-2.2: new low speed USB device using ohci_hcd and address 4 usb 1-2.2: new device found, idVendor=045e, idProduct=0040 usb 1-2.2: new device strings: Mfr=1, Product=3, SerialNumber=0 usb 1-2.2: Product: Microsoft 3-Button Mouse with IntelliEye(TM) usb 1-2.2: Manufacturer: Microsoft usb 1-2.2: configuration #1 chosen from 1 choice usbcore: registered new interface driver hiddev input: Alps Electric M2452 as /class/input/input1 input: USB HID v1.00 Keyboard [Alps Electric M2452] on usb-0000:01:06.0-2.1 input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input2 input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:01:06.0-2.2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: 208k init SCSI subsystem initialized libata version 3.00 loaded. scsi0 : pata_cmd64x scsi1 : pata_cmd64x ata1: PATA max UDMA/25 cmd 0xfd732840 ctl 0xfd732832 bmdma 0xfd732800 irq 26 ata2: PATA max UDMA/25 cmd 0xfd732820 ctl 0xfd732812 bmdma 0xfd732808 irq 26 ata1.00: ATA-3: SAMSUNG SV0432A, KH101, max UDMA/33 ata1.00: 8421840 sectors, multi 16: LBA pata_cmd64x: active 3 recovery 1 setup 1. ata1.00: configured for UDMA/25 scsi 0:0:0:0: Direct-Access ATA SAMSUNG SV0432A KH10 PQ: 0 ANSI: 5 scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs scsi 2:0:0:0: Direct-Access SEAGATE ST34520N 1498 PQ: 0 ANSI: 2 scsi2:A:0:0: Tagged Queuing enabled. Depth 32 target2:0:0: Beginning Domain Validation target2:0:0: FAST-10 SCSI 5.8 MB/s ST (172 ns, offset 15) target2:0:0: Domain Validation skipping write tests target2:0:0: Ending Domain Validation mesh: configured for synchronous 5 MB/s mesh: performing initial bus reset... scsi3 : MESH sd 0:0:0:0: [sda] 8421840 512-byte hardware sectors (4312 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 8421840 512-byte hardware sectors (4312 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sda: [mac] sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk sd 2:0:0:0: [sdb] 8888924 512-byte hardware sectors (4551 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 93 00 10 08 sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 2:0:0:0: [sdb] 8888924 512-byte hardware sectors (4551 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 93 00 10 08 sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sdb: [mac] sdb1 sdb2 sd 2:0:0:0: [sdb] Attached SCSI disk kjournald starting. Commit interval 5 seconds EXT3 FS on sda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 2:0:0:0: Attached scsi generic sg1 type 0 eth0: BMAC+ at 00:05:02:51:4a:56 ide-floppy driver 0.99.newide ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: DMA disabled hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete hdb: No disk in drive hdb: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm hda: ATAPI 32X DVD-ROM drive, 512kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete hdb: No disk in drive ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete Adding 377516k swap on /dev/sda3. Priority:-1 extents:1 across:377516k device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com loop: module loaded kjournald starting. Commit interval 5 seconds EXT3 FS on sdb2, internal journal EXT3-fs: mounted filesystem with ordered data mode. Kernel logging (ksyslog) stopped. Kernel log daemon terminating. Boot logging started on /dev/tty1(/dev/console) at Sun Dec 30 18:37:29 2007 Creating device nodes with udev Waiting for device /dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 to appear: ok fsck 1.40.2 (12-Jul-2007) [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a -C0 /dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 /dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4: clean, 151051/473280 files, 860818/946299 blocks fsck succeeded. Mounting root device read-write. Mounting root /dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 Boot logging started on /dev/tty1(/dev/console (deleted)) at Mon Dec 31 07:37:50 2007 done Starting udevd done Loading required kernel modules doneActivating swap-devices in /etc/fstab... donemount: according to mtab, /dev/sda4 is already mounted on / Activating device mapper... done Checking file systems... fsck 1.40.2 (12-Jul-2007) Home (/dev/disk/by-id/scsi-SSEAGATE_ST34520N_AYU38683-part2): clean, 1623/555968 files, 62603/1111107 blocks donedone Mounting local file systems... proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) debugfs on /sys/kernel/debug type debugfs (rw) udev on /dev type tmpfs (rw) devpts on /dev/pts type devpts (rw,mode=0620,gid=5) /dev/sdb2 on /home type ext3 (rw,noexec,nosuid,nodev,acl,user_xattr) doneSetting up the hardware clockdone killproc: kill(870,29) Creating /var/log/boot.msg doneMounting securityfs on /sys/kernel/security done Loading AppArmor module done Loading AppArmor profiles done Activating remaining swap-devices in /etc/fstab... doneSetting current sysctl status from /etc/sysctl.conf net.ipv4.icmp_echo_ignore_broadcasts = 1 net.ipv4.conf.all.rp_filter = 1 fs.inotify.max_user_watches = 65536 done Enabling syn flood protectiondone Disabling IP forwardingdone done Setting up hostname 'imacg3'done Setting up loopback interface lo lo IP address: 127.0.0.1/8 Checking for network time protocol daemon (NTPD): unused Can't determine current runlevel done System Boot Control: The system has been set up System Boot Control: Running /etc/init.d/boot.local donekillproc: kill(870,3) INIT: Entering runlevel: 5 Boot logging started on /dev/tty1(/dev/console) at Mon Dec 31 07:38:08 2007 Master Resource Control: previous runlevel: N, switching to runlevel: 5 startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/sbin/resmgrd ] Starting resource managerdone Starting D-Bus daemonstartproc: execve (/sbin/syslog-ng) [ /sbin/syslog-ng ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 SPLASHCFG= PWD=/ PREVLEVEL=N LINES=48 SHLVL=2 HOME=/ SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/sbin/syslog-ng ] startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -x -x ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 SPLASHCFG= PWD=/ PREVLEVEL=N LINES=48 SHLVL=2 HOME=/ SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/sbin/klogd ] Starting syslog services.done Unknown username "gdm" in message bus configuration file done startproc: execve (/usr/sbin/console-kit-daemon) [ /usr/sbin/console-kit-daemon ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/usr/sbin/console-kit-daemon ] Starting ConsoleKitdone startproc: execve (/usr/sbin/hald) [ /usr/sbin/hald --daemon=yes ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/usr/sbin/hald ] Starting HAL daemondone Loading CPUFreq modules (CPUFreq not supported) Starting Firewall Initialization (phase 1 of 2) SuSEfirewall2: Warning: ip6tables does not support state matching. Extended IPv6 support disabled. done Starting service kdmstartproc: execve (/opt/kde3/bin/kdm) [ /opt/kde3/bin/kdm ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 INIT_VERSION=sysvinit-2.86 KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 SPLASHCFG= PWD=/ LANG=en_US.UTF-8 PREVLEVEL=N LINES=48 QT_SYSTEM_DIR=/usr/share/desktop-data SHLVL=2 HOME=/ XCURSOR_THEME=crystalwhite WINDOWMANAGER=/usr/bin/kde SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/opt/kde3/bin/kdm ] done Loading keymap mac/all/mac-us.map.gz doneLoading compose table latin1.adddone Start Unicode mode doneLoading console font lat9w-16.psfu -m trivial G0:loadable checkproc: /opt/kde3/bin/kdm 1841 doneSetting up network interfaces: lo lo IP address: 127.0.0.1/8 Starting mouse button emulationdone Initializing random number generatordone Checking for network time protocol daemon (NTPD): unused done eth0 eth0 (DHCP) . . . . . no IP address yet... backgrounding. waiting Waiting for mandatory devices: eth0 __NSC__ 5 pidofproc: dhcpcd 2365 eth0 eth0 DHCP client (dhcpcd) is running eth0 IP address: 10.1.1.3/8 doneSetting up service network . . . . . . . . . . . . . . . done checkproc: /opt/kde3/bin/kdm 1841 startproc: execve (/sbin/auditd) [ /sbin/auditd -s disable ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/sbin/auditd ] Starting auditd done startproc: execve (/usr/sbin/avahi-daemon) [ /usr/sbin/avahi-daemon -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/usr/sbin/avahi-daemon ] killproc: kill(1652,20) Starting Avahi daemon.done killproc: kill(1649,1) killproc: kill(1652,18) killproc: kill(1652,12) Starting Avahi DNS Configuration daemonstartproc: execve (/usr/sbin/avahi-dnsconfd) [ /usr/sbin/avahi-dnsconfd -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/usr/sbin/avahi-dnsconfd ] done Starting Name Service Cache Daemonstartproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/usr/sbin/nscd ] done Starting RPC portmap daemonstartproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/sbin/portmap ] done startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/usr/sbin/cupsd ] Starting cupsddone Starting mail service (Postfix)startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -v 3 ], [ HOME=/ PATH=/bin:/sbin:/usr/bin:/usr/sbin SHELL=/bin/sh RUNLEVEL=5 PREVLEVEL=N DAEMON=/usr/sbin/powersaved ] Starting powersaved: This machine supports APM done done startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/usr/sbin/cron ] Starting CRON daemondone Starting smartd startproc: execve (/usr/sbin/smartd) [ /usr/sbin/smartd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/usr/sbin/smartd ] done startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=ext3 SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin RUNLEVEL=5 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 _=/sbin/startproc DAEMON=/usr/sbin/sshd ] Starting SSH daemondone Starting Firewall Initialization (phase 2 of 2) done done Master Resource Control: runlevel 5 has been reached killproc: kill(1605,3) 1.9 dmesg dmesg | /bin/grep -v SFW2- Using PowerMac machine description Total memory = 192MB; using 512kB for hash table (at cbf80000) Linux version 2.6.22.13-0.3-default (geeko@buildhost) (gcc version 4.2.1 (SUSE Linux)) #1 2007/11/19 15:02:58 UTC Found initrd at 0xc4100000:0xc438c000 Found a Paddington mac-io controller, rev: 0, mapped at 0xfdf80000 PowerMac motherboard: Blue&White G3 Entering add_active_range(0, 0, 49152) 0 entries of 256 used Found Grackle (MPC106) PCI host bridge at 0x0000000080000000. Firmware bus number: 0->1 nvram: OF partition at 0x140 nvram: XP partition at 0xffffffff nvram: NR partition at 0xffffffff Top of RAM: 0xc000000, Total RAM: 0xc000000 Memory hole size: 0MB Zone PFN ranges: DMA 0 -> 49152 Normal 49152 -> 49152 HighMem 49152 -> 49152 early_node_map[1] active PFN ranges 0: 0 -> 49152 On node 0 totalpages: 49152 DMA zone: 384 pages used for memmap DMA zone: 0 pages reserved DMA zone: 48768 pages, LIFO batch:15 Normal zone: 0 pages used for memmap HighMem zone: 0 pages used for memmap Built 1 zonelists. Total pages: 48768 Kernel command line: root=/dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 quiet splash irq: Found primary Apple PIC /pci@80000000/pci-bridge@d/mac-io@5 for 64 irqs irq: System has 64 possible interrupts PID hash table entries: 1024 (order: 10, 4096 bytes) GMT Delta read from XPRAM: 0 minutes, DST: on time_init: decrementer frequency = 24.934450 MHz time_init: processor frequency = 350.000000 MHz Console: colour dummy device 80x25 console handover: boot [udbg0] -> real [tty0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) High memory: 0k Memory: 186232k/196608k available (4388k kernel code, 10060k reserved, 164k data, 467k bss, 208k init) Calibrating delay loop... 49.79 BogoMIPS (lpj=99584) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 device-tree: Duplicate name in /cpus/PowerPC,750@0, renamed to "l2-cache#1" NET: Registered protocol family 16 PCI: Probing PCI hardware PCI: Enabling device 0000:01:04.0 (0014 -> 0017) Registering pmac pic with sysfs... usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered Unpacking initramfs... done Freeing initrd memory: 2608k freed Thermal assist unit using timers, shrink_timer: 500 jiffies audit: initializing netlink socket (disabled) audit(1199039845.656:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Enabling device 0000:00:10.0 (0086 -> 0087) aty128fb: Found Open Firmware ROM Image aty128fb: BIOS not located, guessing timings. aty128fb: Rage128 RE PCI [chip rev 0x2] 16M 128-bit SDR SGRAM (1:1) Console: switching to colour frame buffer device 128x48 fb0: ATY Rage128 frame buffer device on Rage128 RE PCI Generic RTC Driver v1.07 Macintosh non-volatile memory driver v1.1 pmac_zilog: 0.6 (Benjamin Herrenschmidt ) ttyS0 at MMIO 0x80813020 (irq = 16) is a Z85c30 ESCC - Serial port ttyS1 at MMIO 0x80813000 (irq = 17) is a Z85c30 ESCC - Infrared port Serial: MPC52xx PSC UART driver MacIO PCI driver attached to Paddington chipset Can't request resource 0 for MacIO device 0.00000000:power-mg input: Macintosh mouse button emulation as /class/input/input0 Macintosh CUDA driver v0.5 for Unified ADB. apm_emu: PMU APM Emulation initialized. adb: starting probe task... Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx adb devices: adb: finished probe task... ide0: Found Apple Heathrow ATA controller, bus ID 0, irq 32 Probing IDE interface ide0... hda: MATSHITADVD-ROM SR-8583, ATAPI CD/DVD-ROM drive hdb: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive hda: Enabling MultiWord DMA 2 ide0 at 0xcd012000-0xcd012007,0xcd012160 on irq 32 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ohci_hcd 0000:01:06.0: OHCI Host Controller ohci_hcd 0000:01:06.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:01:06.0: irq 28, io mem 0x80880000 usb usb1: new device found, idVendor=0000, idProduct=0000 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: OHCI Host Controller usb usb1: Manufacturer: Linux 2.6.22.13-0.3-default ohci_hcd usb usb1: SerialNumber: 0000:01:06.0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected mice: PS/2 mouse device common for all mice usb 1-2: new full speed USB device using ohci_hcd and address 2 usb 1-2: new device found, idVendor=0409, idProduct=55ab usb 1-2: new device strings: Mfr=0, Product=0, SerialNumber=0 usb 1-2: configuration #1 chosen from 1 choice hub 1-2:1.0: USB hub found hub 1-2:1.0: 4 ports detected usb 1-2.1: new low speed USB device using ohci_hcd and address 3 usb 1-2.1: new device found, idVendor=05ac, idProduct=0201 usb 1-2.1: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-2.1: Product: M2452 usb 1-2.1: Manufacturer: Alps Electric usb 1-2.1: configuration #1 chosen from 1 choice usb 1-2.2: new low speed USB device using ohci_hcd and address 4 usb 1-2.2: new device found, idVendor=045e, idProduct=0040 usb 1-2.2: new device strings: Mfr=1, Product=3, SerialNumber=0 usb 1-2.2: Product: Microsoft 3-Button Mouse with IntelliEye(TM) usb 1-2.2: Manufacturer: Microsoft usb 1-2.2: configuration #1 chosen from 1 choice usbcore: registered new interface driver hiddev input: Alps Electric M2452 as /class/input/input1 input: USB HID v1.00 Keyboard [Alps Electric M2452] on usb-0000:01:06.0-2.1 input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input2 input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:01:06.0-2.2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: 208k init SCSI subsystem initialized libata version 3.00 loaded. scsi0 : pata_cmd64x scsi1 : pata_cmd64x ata1: PATA max UDMA/25 cmd 0xfd732840 ctl 0xfd732832 bmdma 0xfd732800 irq 26 ata2: PATA max UDMA/25 cmd 0xfd732820 ctl 0xfd732812 bmdma 0xfd732808 irq 26 ata1.00: ATA-3: SAMSUNG SV0432A, KH101, max UDMA/33 ata1.00: 8421840 sectors, multi 16: LBA pata_cmd64x: active 3 recovery 1 setup 1. ata1.00: configured for UDMA/25 scsi 0:0:0:0: Direct-Access ATA SAMSUNG SV0432A KH10 PQ: 0 ANSI: 5 scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs scsi 2:0:0:0: Direct-Access SEAGATE ST34520N 1498 PQ: 0 ANSI: 2 scsi2:A:0:0: Tagged Queuing enabled. Depth 32 target2:0:0: Beginning Domain Validation target2:0:0: FAST-10 SCSI 5.8 MB/s ST (172 ns, offset 15) target2:0:0: Domain Validation skipping write tests target2:0:0: Ending Domain Validation mesh: configured for synchronous 5 MB/s mesh: performing initial bus reset... scsi3 : MESH sd 0:0:0:0: [sda] 8421840 512-byte hardware sectors (4312 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 8421840 512-byte hardware sectors (4312 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sda: [mac] sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk sd 2:0:0:0: [sdb] 8888924 512-byte hardware sectors (4551 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 93 00 10 08 sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 2:0:0:0: [sdb] 8888924 512-byte hardware sectors (4551 MB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 93 00 10 08 sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sdb: [mac] sdb1 sdb2 sd 2:0:0:0: [sdb] Attached SCSI disk kjournald starting. Commit interval 5 seconds EXT3 FS on sda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 2:0:0:0: Attached scsi generic sg1 type 0 eth0: BMAC+ at 00:05:02:51:4a:56 ide-floppy driver 0.99.newide ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: DMA disabled hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete hdb: No disk in drive hdb: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm hda: ATAPI 32X DVD-ROM drive, 512kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete hdb: No disk in drive ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete Adding 377516k swap on /dev/sda3. Priority:-1 extents:1 across:377516k device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com loop: module loaded kjournald starting. Commit interval 5 seconds EXT3 FS on sdb2, internal journal EXT3-fs: mounted filesystem with ordered data mode. AppArmor: AppArmor initialized audit(1199039880.374:2): type=1505 info="AppArmor initialized" pid=1420 NET: Registered protocol family 10 lo: Disabled Privacy Extensions Mobile IPv6 ip6_tables: (C) 2000-2006 Netfilter Core Team ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1536 buckets, 12288 max) phy registers: 1400 782d 7810 0001 00a1 45e1 0001 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 4000 0000 2ffb 0010 0000 0002 0001 0000 0000 0000 0000 0000 0000 0000 eth0: no IPv6 routers present audit(1199039928.554:3): audit_pid=2676 old=0 by auid=4294967295 ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete hdb: No disk in drive ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ISO 9660 Extensions: RRIP_1991A st: Version 20070203, fixed bufsize 32768, s/g segs 256 ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete hdb: No disk in drive ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete ide-floppy: CoD != 0 in idefloppy_pc_intr hdb: ATAPI reset complete hdb: No disk in drive ------------------------------------------------------------------------------- 1.10 scsi - /usr/sbin/hwinfo --scsi 14: SCSI 200.0: 10600 Disk [Created at block.233] UDI: /org/freedesktop/Hal/devices/storage_serial_SSEAGATE_ST34520N_AYU38683 Unique ID: TGKD.+X1yG9OIXC4 Parent ID: fCTE.WcoZRDyx1x7 SysFS ID: /block/sdb SysFS BusID: 2:0:0:0 SysFS Device Link: /devices/pci0000:00/0000:00:0d.0/0000:01:04.0/host2/target2:0:0/2:0:0:0 Hardware Class: disk Model: "SEAGATE ST34520N" Vendor: "SEAGATE" Device: "ST34520N" Revision: "1498" Serial ID: "AYU38683" Driver: "aic7xxx", "sd" Driver Modules: "aic7xxx" Device File: /dev/sdb (/dev/sg1) Device Files: /dev/sdb, /dev/disk/by-id/scsi-SSEAGATE_ST34520N_AYU38683, /dev/disk/by-path/pci-0000:01:04.0-scsi-0:0:0:0 Device Number: block 8:16-8:31 (char 21:1) Geometry (Logical): CHS 1016/141/62 Size: 8888924 sectors a 512 bytes Config Status: cfg=no, avail=yes, need=no, active=unknown Attached to: #8 (SCSI storage controller) ------------------------------------------------------------------------------- 1.11 media links - --- /cd - /dvd --- --- /media/ --- total 6 dr-xr-xr-x 9 linux root 6144 Sep 28 09:25 SU1030.001 --- /dev/cdr* --- lrwxrwxrwx 1 root root 3 Dec 31 07:37 /dev/cdrom -> hda --- /dev/dvd* --- lrwxrwxrwx 1 root root 3 Dec 31 07:37 /dev/dvd -> hda --- /dev/cdrecorder* --- ls: cannot access /dev/cdrecorder*: No such file or directory --- /dev/fd? --- ls: cannot access /dev/fd?: No such file or directory ------------------------------------------------------------------------------- 1.12 hwinfo-storage - /usr/sbin/hwinfo --storage_ctrl 08: PCI 101.0: 0101 IDE interface [Created at pci.301] UDI: /org/freedesktop/Hal/devices/pci_1095_646 Unique ID: j+MN.yKFryAhlHV9 Parent ID: 1h7f.DcyY42OskFA SysFS ID: /devices/pci0000:00/0000:00:0d.0/0000:01:01.0 SysFS BusID: 0000:01:01.0 Hardware Class: storage Model: "Silicon Image PCI0646" Vendor: pci 0x1095 "Silicon Image, Inc." Device: pci 0x0646 "PCI0646" SubVendor: pci 0x1095 "Silicon Image, Inc." SubDevice: pci 0x0646 Revision: 0x05 Driver: "pata_cmd64x" Driver Modules: "pata_cmd64x" I/O Ports: 0x1840-0x1847 (rw) I/O Ports: 0x1830-0x1833 (rw) I/O Ports: 0x1820-0x1827 (rw) I/O Ports: 0x1810-0x1813 (rw) I/O Ports: 0x1800-0x180f (rw) IRQ: 26 (20071 events) Module Alias: "pci:v00001095d00000646sv00001095sd00000646bc01sc01i8f" Driver Info #0: Driver Status: pata_cmd64x is active Driver Activation Cmd: "modprobe pata_cmd64x" Driver Info #1: Driver Status: cmd64x is not active Driver Activation Cmd: "modprobe cmd64x" Config Status: cfg=no, avail=yes, need=no, active=unknown Attached to: #5 (PCI bridge) 09: PCI 104.0: 0100 SCSI storage controller [Created at pci.301] UDI: /org/freedesktop/Hal/devices/pci_9004_5078 Unique ID: fCTE.WcoZRDyx1x7 Parent ID: 1h7f.DcyY42OskFA SysFS ID: /devices/pci0000:00/0000:00:0d.0/0000:01:04.0 SysFS BusID: 0000:01:04.0 Hardware Class: storage Model: "Adaptec AHA-2904/Integrated AIC-7850" Vendor: pci 0x9004 "Adaptec" Device: pci 0x5078 "AHA-7850" SubVendor: pci 0x9004 "Adaptec" SubDevice: pci 0x7850 "AHA-2904/Integrated AIC-7850" Revision: 0x03 Driver: "aic7xxx" Driver Modules: "aic7xxx" I/O Ports: 0x1400-0x14ff (rw,disabled) Memory Range: 0x80881000-0x80881fff (rw,non-prefetchable) IRQ: 25 (3627 events) Module Alias: "pci:v00009004d00005078sv00009004sd00007850bc01sc00i00" Driver Info #0: Driver Status: aic7xxx is active Driver Activation Cmd: "modprobe aic7xxx" Config Status: cfg=no, avail=yes, need=no, active=unknown Attached to: #5 (PCI bridge) 12: None 00.0: 0100 SCSI storage controller [Created at pci.615] Unique ID: SZ2a.jTVTd6bM0WB Parent ID: dx9s.xWNNVcdS2SF SysFS ID: /devices/pci0000:00/0000:00:0d.0/0000:01:05.0/0.80800000:mac-io/0.00010000:scsi SysFS BusID: 0.00010000:scsi Hardware Class: storage Model: "Apple Paddington Mac I/O" Vendor: pci 0x106b "Apple Computer Inc." Device: pci 0x0017 "Paddington Mac I/O" Driver: "mesh" Module Alias: "of:NscsiTscsiCchrp,mesh0" Driver Info #0: Driver Status: mesh is active Driver Activation Cmd: "modprobe mesh" Config Status: cfg=no, avail=yes, need=no, active=unknown Attached to: #10 (Unclassified device) 16: None 00.0: 0101 IDE interface [Created at misc.347] Unique ID: rdCR.Q7WBcPJmFl4 Hardware Class: storage Model: "IDE interface" Compatible to: int 0x3000 0x1000 IRQ: 32 (11080 events) Driver Info #0: Driver Status: ide-generic is not active Driver Activation Cmd: "modprobe ide-generic" Config Status: cfg=no, avail=yes, need=no, active=unknown ------------------------------------------------------------------------------- 3. Configuration ------------------------------------------------------------------------------- 2.1 grub - /boot/grub/menu.lst file /boot/grub/menu.lst not found ------------------------------------------------------------------------------- 2.2 device.map - /boot/grub/device.map file /boot/grub/device.map not found ------------------------------------------------------------------------------- 2.3 grub.conf - /etc/grub.conf file /etc/grub.conf not found ------------------------------------------------------------------------------- 2.4 lilo.conf - /etc/lilo.conf activate timeout = 80 default = Linux boot = /dev/sda2 image = /boot/vmlinux-2.6.22.13-0.3-default label = Linux initrd = /boot/initrd-2.6.22.13-0.3-default append = "quiet splash" root = /dev/disk/by-id/scsi-SATA_SAMSUNG_SV0432A0093J1CK403529-part4 ------------------------------------------------------------------------------- 2.5 lilo_test - /sbin/lilo -v 3 -t lilo for PowerPC 10.1.22 ------------------------------------------------------------------------------- ##Y2support-/tmp/siga/siga.txt-- -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User dmuhamedagic@novell.com added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c1 Dejan Muhamedagic <dmuhamedagic@novell.com> changed: What |Removed |Added ---------------------------------------------------------------------------- CC| |dmuhamedagic@novell.com --- Comment #1 from Dejan Muhamedagic <dmuhamedagic@novell.com> 2008-01-02 10:39:04 MST --- Could you try appending: video=aty128fb to the kernel parameters and see if that helps. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User dmuhamedagic@novell.com added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c3 --- Comment #3 from Dejan Muhamedagic <dmuhamedagic@novell.com> 2008-01-02 13:30:53 MST --- If there's no bootsplash in the config, then bootsplash won't work. I don't know why it was excluded from the kernel. Anyway, splashy is a user space program, so that should work and, given the platform, I guess that you should be better off with that. It seems like you should create an initrd which includes splashy: there's /lib/mkinitrd/scripts/setup-splashy.sh. Did you create one? Must say that I've never used it, so I can't offer any advice on how to set it up. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User hammett@orcon.net.nz added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c4 --- Comment #4 from Quentin Sciascia <hammett@orcon.net.nz> 2008-01-02 18:11:05 MST --- Can you point me into the direction of whoever reversed the bootsplash patch, or where I can get the latest bootsplash patch. The bootsplash patch on the bootsplash website is for kernel 2.6.15.x, and when I have tried to apply it, it ruins the kernel sources so I cannot compile until I remove the kernel sources and reinstall them. Splashy is not working and as far as we can tell it is not being called at all. We tested it on two-G3s, a G4 and G5 with no luck. We add splash splash=silent vga= video= and still splashy is not being called. We looked at the boot.msg and we confirmed that splashy is not actually being called at startup in the initrd. We can test splashy with splashy boot splashy test and all is fine. We even edited the /etc/init.d/boot and added /bin/splashy boot after /proc was started, which worked, but just brings up the boot screen with no progress bar. SO there is nothing wrong with the video settings, and everything to do with how splashy is being setup on a PPC. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User dmuhamedagic@novell.com added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c5 Dejan Muhamedagic <dmuhamedagic@novell.com> changed: What |Removed |Added ---------------------------------------------------------------------------- CC| |olh@novell.com, hmacht@novell.com --- Comment #5 from Dejan Muhamedagic <dmuhamedagic@novell.com> 2008-01-03 05:19:50 MST --- splashy has not yet been setup to work with boot in openSUSE 10.3. Sorry for misdirecting you. Anyhow, I still think that it might be easier to make that work rather than bootsplash. There must've been a good reason not to include that patch with the ppc kernel. Also, splashy is going to be used in the future SuSE products. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User hammett@orcon.net.nz added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c6 --- Comment #6 from Quentin Sciascia <hammett@orcon.net.nz> 2008-01-07 10:57:17 MST --- Hi After several days of hunting we have found out where the problems for splashy lie on PPC. I have emailed the maintainer of the setup-splashy.sh script (hmacht@suse.de) in hopes they may shed some light on the problem. This is what we have found thus far. 1. The splashy script /lib/mkinitrd/scripts/setup-splashy.sh looks for the file /usr/sbin/resume & the directory /etc/splashy. If it doesn't find both it doesn't make the directory /etc/splashy and populate it, or copy the lib files to /usr/lib/ and lib/ in mkinitrd. if [ -d /etc/splashy ] && [ -f /usr/sbin/resume ]; then # find the current theme DUMMY=$(cat /etc/splashy/config.xml) THEME=$(echo $DUMMY | perl -p -e 's/<!--.*?--
//g;s/^.*<current_theme>//;s/<\/current_theme>.*$//;') if [ -z $THEME -o ! -d /etc/splashy/themes/$THEME ]; then echo "$0: warning, splashy theme not found in config file, using 'openSUSE'" THEME=openSUSE fi
I changed the above to if [ -d /etc/splashy ] && [ -f /usr/sbin/pm-suspend ]; then # find the current theme DUMMY=$(cat /etc/splashy/config.xml) THEME=$(echo $DUMMY | perl -p -e 's/<!--.*?--
//g;s/^.*<current_theme>//;s/<\/current_theme>.*$//;') if [ -z $THEME -o ! -d /etc/splashy/themes/$THEME ]; then echo "$0: warning, splashy theme not found in config file, using 'openSUSE'" THEME=openSUSE fi
This makes, and populates the /etc/splashy /libs /usr/libs folders with all the necessary splashy files in them, in initrd, but a new problem arises: When mkinitrd is run and the init script inside initrd is dynamically linked to the splashy binaries in /usr/sbin there is an error, apparently SuSE 10.3 loads a heck of a lot of 64-bit libraries and binaries. The ld command tries to link/run/? (I am a little fuzzy on this point?) some 64-bit libs and fails with error output. mkinitrd continues and then exits. God I hope i have made myself clear, if you need any more detailed information please get a hold of me. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User dmuhamedagic@novell.com added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c7 --- Comment #7 from Dejan Muhamedagic <dmuhamedagic@novell.com> 2008-01-07 11:44:26 MST --- Thanks for the efforts to make it work. Can you please provide the errors which ld produced. FWIW, on my i386 the initrd is produced properly, but there's a whole lot missing to make splashy work. At least when I compare that to what Debian has. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User hammett@orcon.net.nz added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c8 --- Comment #8 from Quentin Sciascia <hammett@orcon.net.nz> 2008-01-07 15:40:22 MST --- Hi Again Okay when I run mkinitrd this is the error output imacg3:/boot # mkinitrd -v Kernel image: /boot/vmlinux-2.6.22.13-0.3-default Initrd image: /boot/initrd-2.6.22.13-0.3-default Root device: /dev/disk/by-id/scsi-SATA_QUANTUM_FIREBAL376904465598-part4 (/dev/sda4) (mounted on / as ext3) [BLOCK] /dev/sda -> pata_cmd64x [BLOCK] /dev/sda -> sd_mod [MODULES] 02-start.sh: pata_cmd64x aic7xxx mesh [MODULES] 11-block.sh: pata_cmd64x sd_mod [MODULES] 11-usb.sh: usbcore [MODULES] 11-usb.sh: ohci_hcd [MODULES] 11-usb.sh: uhci-hcd [MODULES] 11-usb.sh: ehci_hcd [MODULES] 11-usb.sh: usbhid [MODULES] 84-mount.sh: WARNING Cannot determine dependencies of kernel module 'ohci_hcd'. Does it exist? If it does, try depmod -a. Continuing without ohci_hcd. Kernel Modules: scsi_mod libata pata_cmd64x scsi_transport_spi aic7xxx mesh sd_mod uhci-hcd ehci-hcd [MOUNT] Root: /dev/disk/by-id/scsi-SATA_QUANTUM_FIREBAL376904465598-part4 Features: block usb resume.kernel Shared libs: /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) lib/ld-2.6.1.so lib/libacl.so.1.1.0 lib/libattr.so.1.1.0 lib/libblkid.so.1.0 lib/libcom_err.so.2.1 lib/libc-2.6.1.so lib/libdl-2.6.1.so lib/libext2fs.so.2.4 lib/libhistory.so.5.2 lib/libncurses.so.5.6 lib/libpthread-2.6.1.so lib/libreadline.so.5.2 lib/librt-2.6.1.so lib/libutil-2.6.1.so lib/libuuid.so.1.2 lib/libvolume_id.so.0.79.0 lib/libnss_files-2.6.1.so lib/libnss_files.so.2 lib/libgcc_s.so.1 12515 blocks It seems to me that it is trying to use a 64-bit lib, and is getting nowhere. I was wondering if you could contact the splashy script maintainer and ask him how the splashy script sets up placing the splashy binaries from /usr/sbin/ into initrd? I can't find anything in the setup-splashy.sh script that does this, and am "assuming" somewhere/somehow the init script in initrd is dynamically linked to these binaries. BTW - this mkinitrd was done on another fresh install of SuSE 10.3 PPC, not carrying my modified setup-splashy.sh script. The same error is evident, however, on a system carrying the modified script as well. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User dmuhamedagic@novell.com added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c9 --- Comment #9 from Dejan Muhamedagic <dmuhamedagic@novell.com> 2008-01-07 17:02:31 MST --- There are additional two problems you found, unrelated to splash: 1. Missing ohci_hcd. Or something with it. 2. ldd fails with the given error. I'll open additional bugzillas for those. As for splashy, it wasn't even included in the initrd, at least according to this log. Or can you confirm otherwise by unpacking the initrd? BTW, does your boot really need usb in the initrd? -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User hammett@orcon.net.nz added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c10 --- Comment #10 from Quentin Sciascia <hammett@orcon.net.nz> 2008-01-07 17:33:38 MST --- Okay The previous post was for a new install, and you are right, no splashy initrd report, and that is the problem. If you unpack initrd, as you suggested none of the files/directores listed in the setup-splashy.sh script are included into initrd, that is because of the first line in the setup-splashy.sh script (which can be found in /lib/mkinitrd/scripts/: if [ -d /etc/splashy ] && [ -f /usr/sbin/resume ]; then Essentially its says that both the splashy directory AND the file resume MUST be there in order for the setup-splashy.sh script to continue. If they are not BOTH there then the script aborts and mkinitrd continues on its way, without building splashy support into the initrd. I altered the above line to: if [ -d /etc/splashy ]; then After this alteration, and running mkinitrd again, you get the same old errors as the previous post, but you can unpack initrd and sure enough the splashy files in /lib/, /usr/lib, and /etc/splashy are there: imacg3:/boot # mkinitrd -v Kernel image: /boot/vmlinux-2.6.22.13-0.3-default Initrd image: /boot/initrd-2.6.22.13-0.3-default Root device: /dev/disk/by-id/scsi-SATA_QUANTUM_FIREBAL376904465598-part4 (/dev/sda4) (mounted on / as ext3) [BLOCK] /dev/sda -> pata_cmd64x [BLOCK] /dev/sda -> sd_mod [MODULES] 02-start.sh: pata_cmd64x aic7xxx mesh [MODULES] 11-block.sh: pata_cmd64x sd_mod [MODULES] 11-usb.sh: usbcore [MODULES] 11-usb.sh: ohci_hcd [MODULES] 11-usb.sh: uhci-hcd [MODULES] 11-usb.sh: ehci_hcd [MODULES] 11-usb.sh: usbhid [MODULES] 84-mount.sh: WARNING Cannot determine dependencies of kernel module 'ohci_hcd'. Does it exist? If it does, try depmod -a. Continuing without ohci_hcd. Kernel Modules: scsi_mod libata pata_cmd64x scsi_transport_spi aic7xxx mesh sd_mod uhci-hcd ehci-hcd [MOUNT] Root: /dev/disk/by-id/scsi-SATA_QUANTUM_FIREBAL376904465598-part4 Features: block usb resume.kernel Shared libs: /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) /usr/bin/ldd: line 161: /lib64/ld64.so.1: cannot execute binary file ldd: exited with unknown exit code (126) lib/ld-2.6.1.so lib/libacl.so.1.1.0 lib/libattr.so.1.1.0 lib/libblkid.so.1.0 lib/libcom_err.so.2.1 lib/libc-2.6.1.so lib/libdl-2.6.1.so lib/libext2fs.so.2.4 lib/libhistory.so.5.2 lib/libncurses.so.5.6 lib/libpthread-2.6.1.so lib/libreadline.so.5.2 lib/librt-2.6.1.so lib/libutil-2.6.1.so lib/libuuid.so.1.2 lib/libvolume_id.so.0.79.0 lib/libnss_files-2.6.1.so lib/libnss_files.so.2 lib/libgcc_s.so.1 However splashy still does not work. I believe this is because in SuSE 10.3, that the initrd is dynamically linked to the splashy binaries in /usr/sbin/ through the files /usr/$LIBDIR/libsplashy.so.1 /usr/$LIBDIR/libsplashycnf.so.1, rather than the binaries being placed in the initrd, since there is no section within the setup-splashy.sh script (below) that does this (point me out if I am wrong). imacg3:/boot # cat /lib/mkinitrd/scripts/setup-splashy.sh #!/bin/bash # # Copyright (C) 2007 SUSE Linux Products GmbH # # Author: Holger Macht <hmacht@suse.de> # # This file is released under the GPLv2. # #%stage: setup # # never even 'return' from a mkinitrd script, which would result in an # aborted initrd build process if [ -d /etc/splashy ]; then # find the current theme DUMMY=$(cat /etc/splashy/config.xml) THEME=$(echo $DUMMY | perl -p -e 's/<!--.*?-->//g;s/^.*<current_theme>//;s/<\/current_theme>.*$//;') if [ -z $THEME -o ! -d /etc/splashy/themes/$THEME ]; then echo "$0: warning, splashy theme not found in config file, using 'openSUSE'" THEME=openSUSE fi LIBDIR=lib if [ "`LANG=C LC_ALL=C file -b /usr/sbin/resume | awk '/^ELF ..-bit/ { print $2 }'`" = "64-bit" ]; then LIBDIR=lib64 fi LIBS="\ /usr/$LIBDIR/libdirect-1.0.so.0 \ /usr/$LIBDIR/libdirectfb-1.0.so.0 \ /usr/$LIBDIR/libfusion-1.0.so.0 \ /usr/$LIBDIR/libpng12.so.0 \ /usr/$LIBDIR/libglib-2.0.so.0 \ /usr/$LIBDIR/libsplashy.so.1 \ /usr/$LIBDIR/libsplashycnf.so.1 \ /$LIBDIR/libsysfs.so.2 \ /$LIBDIR/libm.so.6 \ /$LIBDIR/libz.so.1" SPLASHY_FILES=" /etc/splashy/config.xml \ /etc/splashy/themes/$THEME/*" for I in `directfb-config --libs --input=keyboard --imageprovider=jpeg,gif,png --font=ft2,default`; do F=`dirname -- $I`/`basename -- $I .o`.so if [ -f $F ]; then if [ ! -d $tmp_mnt/`dirname $F` ]; then mkdir -p $tmp_mnt/`dirname $F` fi cp -dp $F $tmp_mnt/$F fi done for I in $LIBS; do [ ! -d $tmp_mnt/`dirname $I` ] && mkdir -p $tmp_mnt/`dirname $I` cp -L $I $tmp_mnt/$I done for I in $SPLASHY_FILES; do [ ! -d $tmp_mnt/`dirname $I` ] && mkdir -p $tmp_mnt/`dirname $I` cp $I $tmp_mnt/$I done fi # never exit with nonzero, so we never cause mkinitrd to abort # - not having splash during resume is ugly, not booting is evil. # do not exit here - this script is sourced! true To be sure though, I altered a section of the script above to that below, and ran mkinitrd again: SPLASHY_FILES=" /usr/sbin/splashy* \ /etc/splashy/config.xml \ /etc/splashy/themes/$THEME/*" This placed the splashy binaries from /usr/sbin/ into initrd, but did not work. Any hints? -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User hmacht@novell.com added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c11 Holger Macht <hmacht@novell.com> changed: What |Removed |Added ---------------------------------------------------------------------------- CC| |mls@novell.com --- Comment #11 from Holger Macht <hmacht@novell.com> 2008-01-08 05:41:55 MST --- Until now, splashy is only used for suspend to disk in openSUSE. There have not been any efforts yet to make it work for usual boot. The script checks for the resume binary and moves the splashy dependencies only to the initrd if it is found because working userpace suspend/resume tools are needed. The setup-splashy.sh script hardcodes some of the needed libraries for splashy in current versions. This is optimized for i386 and x86_64 only. This is ugly, yes, but there is no other way because libdirectfb pulls some libraries at runtime which cannot be figured out with ldd. Hope this clarifies a bit. Maybe we'll use splashy for future openSUSE versions, but that's not decided yet. I'm adding Michael Schroeder to CC, because he might know why bootsplash is not enabled in PPC. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User mls@novell.com added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c12 --- Comment #12 from Michael Schröder <mls@novell.com> 2008-01-08 06:02:37 MST --- No, sorry, I can't help you with this. AFAICR the bootsplash code worked on ppc. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User dmuhamedagic@novell.com added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c13 Dejan Muhamedagic <dmuhamedagic@novell.com> changed: What |Removed |Added ---------------------------------------------------------------------------- CC| |jeffm@novell.com --- Comment #13 from Dejan Muhamedagic <dmuhamedagic@novell.com> 2008-01-08 10:20:47 MST --- I thought that splashy _is_ going to make the bootsplash obsolete in the openSUSE too. Any other options? Yes, I understand that it is not a trivial task to adjust the openSUSE booting to use splashy. Jeff: Who was responsible for the powerpc kernel? Any other ideas how to fix this if bootsplash can't be used and if splashy is not exactly ready for openSUSE (or the other way around)? -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User hammett@orcon.net.nz added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c14 --- Comment #14 from Quentin Sciascia <hammett@orcon.net.nz> 2008-01-08 13:17:08 MST --- IT would be great to know who is in charge of the PPC kernel, and why bootsplash has been disabled in it. I know a bootsplash is not a critical system element, but for new users its essential. Our usability tests showed 3/5 people walked away from our test machines when the lovely verbose boot mode kicks in cause they think its broken. Cheers for your help guys -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User dmuhamedagic@novell.com added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c16 Dejan Muhamedagic <dmuhamedagic@novell.com> changed: What |Removed |Added ---------------------------------------------------------------------------- Status|ASSIGNED |NEEDINFO Info Provider| |olh@novell.com --- Comment #16 from Dejan Muhamedagic <dmuhamedagic@novell.com> 2008-06-03 13:41:32 MDT --- Olaf: Can you supply any useful information? Thanks. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User olh@novell.com added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c17 Olaf Hering <olh@novell.com> changed: What |Removed |Added ---------------------------------------------------------------------------- Status|NEEDINFO |ASSIGNED Info Provider|olh@novell.com | --- Comment #17 from Olaf Hering <olh@novell.com> 2008-06-03 14:24:28 MDT --- There are userspace solutions to display a splash screen during boot. Use them. No need for a kernel patch. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User dmuhamedagic@novell.com added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c19 Dejan Muhamedagic <dmuhamedagic@novell.com> changed: What |Removed |Added ---------------------------------------------------------------------------- AssignedTo|dmuhamedagic@novell.com |bnc-team-screening@forge.provo.novell.com Status|ASSIGNED |NEW Component|Kernel |Basesystem --- Comment #19 from Dejan Muhamedagic <dmuhamedagic@novell.com> 2008-12-02 05:07:59 MST --- Obviously not easy to fix for 10.3. Hope that we have this back in 11.0 or 11.1. Reassigning back to qa. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User aorlovskyy@novell.com added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c20 Alexander Orlovskyy <aorlovskyy@novell.com> changed: What |Removed |Added ---------------------------------------------------------------------------- CC| |aorlovskyy@novell.com Status|NEW |NEEDINFO Info Provider| |hammett@orcon.net.nz --- Comment #20 from Alexander Orlovskyy <aorlovskyy@novell.com> 2008-12-17 05:58:16 MST --- Quentin, can you test this issue on openSUSE 11.1? -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 User aorlovskyy@novell.com added comment https://bugzilla.novell.com/show_bug.cgi?id=350993#c21 Alexander Orlovskyy <aorlovskyy@novell.com> changed: What |Removed |Added ---------------------------------------------------------------------------- Status|NEEDINFO |RESOLVED Info Provider|hammett@orcon.net.nz | Resolution| |NORESPONSE --- Comment #21 from Alexander Orlovskyy <aorlovskyy@novell.com> 2008-12-22 01:35:36 MST --- If you can provide the requested information, please reopen this bug. -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
https://bugzilla.novell.com/show_bug.cgi?id=350993 Alexander Orlovskyy <aorlovskyy@novell.com> changed: What |Removed |Added ---------------------------------------------------------------------------- Status|RESOLVED |CLOSED -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.
participants (1)
-
bugzilla_noreply＠novell.com