https://bugzilla.novell.com/show_bug.cgi?id=440928 User monkey9@iae.nl added comment https://bugzilla.novell.com/show_bug.cgi?id=440928#c27 Robby Verberne <monkey9@iae.nl> changed: What |Removed |Added ---------------------------------------------------------------------------- Status|NEEDINFO |NEW Info Provider|monkey9@iae.nl | --- Comment #27 from Robby Verberne <monkey9@iae.nl> 2008-11-26 03:09:33 MST --- After killing dhc, and dhcpcd wlan0, i did not get an ip address. I don't use encryption because i first want a connection. ARM500-sfn7:/home/oddball # iwlist wlan0 scan essid linksys wlan0 Scan completed : Cell 01 - Address: 00:1E:E5:70:49:B8 ESSID:"linksys" Mode:Master Channel:11 Frequency:2.462 GHz (Channel 11) Quality=39/100 Signal level:-65 dBm Noise level=-90 dBm Encryption key:off Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s 48 Mb/s; 54 Mb/s Extra:tsf=0000005b4f9f8052 Extra: Last beacon: 68ms ago Cell 02 - Address: 00:1C:10:66:4B:A7 ESSID:"linksys" Mode:Master Channel:11 Frequency:2.462 GHz (Channel 11) Quality=31/100 Signal level:-70 dBm Noise level=-90 dBm Encryption key:off Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Extra:tsf=0000005b4f8ca267 Extra: Last beacon: 72ms ago ARM500-sfn7:/home/oddball # ifconfig wlan0 up ARM500-sfn7:/home/oddball # iwconfig wlan0 essid linksys ARM500-sfn7:/home/oddball # iwconfig wlan0 wlan0 IEEE 802.11bg ESSID:"linksys" Mode:Managed Frequency:2.462 GHz Access Point: 00:1E:E5:70:49:B8 Bit Rate=1 Mb/s Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality=40/100 Signal level:-65 dBm Noise level=-91 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ARM500-sfn7:/home/oddball # ps -A | grep dhc 3206 ? 00:00:00 dhcpcd 10598 ? 00:00:00 dhclient 14427 ? 00:00:00 dhclient ARM500-sfn7:/home/oddball # kill pid 3206, 10598, 14427 bash: kill: pid: arguments must be process or job IDs bash: kill: 3206,: arguments must be process or job IDs bash: kill: 10598,: arguments must be process or job IDs ARM500-sfn7:/home/oddball # dhcpcd wlan0 err, wlan0: timed out warn, wlan0: using IPV4LL address 169.254.64.48 ARM500-sfn7:/home/oddball # dhcpcd wlan0 err, wlan0: dhcpcd already running on pid 15662 (/var/run/dhcpcd-wlan0.pid) ARM500-sfn7:/home/oddball # iwconfig wlan0 wlan0 IEEE 802.11bg ESSID:"linksys" Mode:Managed Frequency:2.462 GHz Access Point: 00:1E:E5:70:49:B8 Bit Rate=2 Mb/s Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality=32/100 Signal level:-70 dBm Noise level=-91 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 dmesg: (part) name="/usr/sbin/traceroute" name2="default" pid=1782 powernow: This module only works with AMD K7 CPUs e100: eth0: e100_watchdog: link up, 10Mbps, half-duplex NET: Registered protocol family 17 NET: Registered protocol family 10 lo: Disabled Privacy Extensions eth0: no IPv6 routers present ADDRCONF(NETDEV_UP): wlan0: link is not ready wlan0: authenticate with AP 00:1c:10:66:4b:a7 wlan0: authenticate with AP 00:1c:10:66:4b:a7 wlan0: authenticated wlan0: associate with AP 00:1c:10:66:4b:a7 wlan0: associate with AP 00:1c:10:66:4b:a7 wlan0: associate with AP 00:1c:10:66:4b:a7 wlan0: association with AP 00:1c:10:66:4b:a7 timed out JBD: barrier-based sync failed on hda7 - disabling barriers wlan0: authenticate with AP 00:1c:10:66:4b:a7 wlan0: authenticated wlan0: associate with AP 00:1c:10:66:4b:a7 wlan0: RX AssocResp from 00:1c:10:66:4b:a7 (capab=0x401 status=0 aid=3) wlan0: associated ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready wlan0: disassociating by local choice (reason=3) wlan0: No ProbeResp from current AP 00:1c:10:66:4b:a7 - assume out of range wlan0: no IPv6 routers present e100: eth0: e100_watchdog: link down wlan0: authenticate with AP 00:1c:10:66:4b:a7 wlan0: authenticated wlan0: associate with AP 00:1c:10:66:4b:a7 e100: eth0: e100_watchdog: link up, 10Mbps, half-duplex wlan0: authenticate with AP 00:1c:10:66:4b:a7 ADDRCONF(NETDEV_UP): wlan0: link is not ready wlan0: authenticated wlan0: associate with AP 00:1c:10:66:4b:a7 wlan0: RX AssocResp from 00:1c:10:66:4b:a7 (capab=0x401 status=0 aid=3) wlan0: associated ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready wlan0: disassociating by local choice (reason=3) wlan0: No ProbeResp from current AP 00:1c:10:66:4b:a7 - assume out of range wlan0: no IPv6 routers present wlan0: deauthenticated ath5k phy0: failed to wakeup the MAC Chip ath5k phy0: can't reset hardware (-5) pccard: card ejected from slot 0 ath5k_pci 0000:02:00.0: PCI INT A disabled pccard: CardBus card inserted into slot 0 PCI: 0000:02:00.0 reg 10 32bit mmio: [0, ffff] ath5k_pci 0000:02:00.0: enabling device (0000 -> 0002) ath5k_pci 0000:02:00.0: PCI INT A -> Link[C142] -> GSI 11 (level, low) -> IRQ 11 ath5k_pci 0000:02:00.0: registered as 'phy1' phy1: Selected rate control algorithm 'pid' ath5k phy1: Atheros AR5213 chip found (MAC: 0x56, PHY: 0x41) ath5k phy1: RF5111 5GHz radio found (0x17) ath5k phy1: RF2111 2GHz radio found (0x23) ADDRCONF(NETDEV_UP): wlan0: link is not ready wlan0: authenticate with AP 00:1e:e5:70:49:b8 wlan0: authenticated wlan0: associate with AP 00:1e:e5:70:49:b8 wlan0: RX AssocResp from 00:1e:e5:70:49:b8 (capab=0x421 status=0 aid=2) wlan0: associated ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready wlan0: disassociating by local choice (reason=3) wlan0: no IPv6 routers present wlan0: authenticate with AP 00:1e:e5:70:49:b8 wlan0: authenticated wlan0: associate with AP 00:1e:e5:70:49:b8 wlan0: RX ReassocResp from 00:1e:e5:70:49:b8 (capab=0x421 status=0 aid=2) wlan0: associated wlan0: disassociating by local choice (reason=3) -- Configure bugmail: https://bugzilla.novell.com/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are on the CC list for the bug.