Hallo, kann mir bitte jemand bei folgendem Problem helfen? Ich habe eine IDE-Platte mit 120GB in ein Gehäuse eingebaut und das per USB angeschlosen. Kernel 2.4.19, SuSE 8.1. Folgendes habe ich den Kernelmeldungen entnommen: Dec 28 14:13:26 linux kernel: hub.c: USB new device connect on bus1/1, assigned device number 3 Dec 28 14:13:26 linux kernel: usb.c: USB device 3 (vend/prod 0x5e3/0x702) is not claimed by any active driver. Dec 28 14:13:28 linux kernel: Initializing USB Mass Storage driver... Dec 28 14:13:28 linux kernel: usb.c: registered new driver usb-storage Dec 28 14:13:28 linux kernel: scsi: limiting sg entries to 204 Dec 28 14:13:28 linux kernel: scsi1 : SCSI emulation for USB Mass Storage devices Dec 28 14:13:28 linux kernel: Vendor: EagleTec Model: External Hard Di Rev: 0033 Dec 28 14:13:28 linux kernel: Type: Direct-Access ANSI SCSI revision: 02 Dec 28 14:13:28 linux kernel: sd: allocated major 8 Dec 28 14:13:28 linux kernel: sg_attach: dev1=(21:1) Dec 28 14:13:28 linux kernel: sd: find_free_slot ...<7>sd: ... found 08:00 Dec 28 14:13:28 linux kernel: Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0 Dec 28 14:13:28 linux kernel: SCSI device sda: 234493056 512-byte hdwr sectors (120060 MB) Dec 28 14:13:28 linux kernel: usb-uhci.c: interrupt, status 2, frame# 182 Dec 28 14:13:28 linux kernel: sda: test WP failed, assume Write Enabled Dec 28 14:13:28 linux kernel: sda: sda1 Soweit sieht ja alles gut aus, die Platte hat nämlich nur eine Partition und die scheint erkannt zu sein. Nun geht's aber weiter: Dec 28 14:13:28 linux kernel: WARNING: USB Mass Storage data integrity not assured Dec 28 14:13:28 linux kernel: USB Mass Storage device found at 3 Dec 28 14:13:28 linux kernel: USB Mass Storage support registered. Dec 28 14:13:28 linux insmod: Using /lib/modules/2.4.19-4GB/kernel/drivers/usb/storage/usb-storage.o Dec 28 14:13:28 linux insmod: Symbol version prefix '' Dec 28 14:13:29 linux kernel: SCSI device (ioctl) reports ILLEGAL REQUEST. Dec 28 14:13:29 linux kernel: SCSI device sda: 234493056 512-byte hdwr sectors (120060 MB) Dec 28 14:13:29 linux kernel: sda: test WP failed, assume Write Enabled Dec 28 14:13:29 linux kernel: sda: I/O error: dev 08:00, sector 0 Dec 28 14:13:29 linux kernel: I/O error: dev 08:00, sector 0 Dec 28 14:13:29 linux kernel: unable to read partition table Dec 28 14:13:29 linux kernel: I/O error: dev 08:00, sector 0 Dec 28 14:13:30 linux kernel: SCSI device (ioctl) reports ILLEGAL REQUEST. Dec 28 14:13:30 linux kernel: SCSI device sda: 234493056 512-byte hdwr sectors (120060 MB) Dec 28 14:13:30 linux kernel: sda: test WP failed, assume Write Enabled Dec 28 14:13:30 linux kernel: sda: I/O error: dev 08:00, sector 0 Dec 28 14:13:30 linux kernel: I/O error: dev 08:00, sector 0 Dec 28 14:13:30 linux kernel: unable to read partition table Dec 28 14:13:30 linux kernel: SCSI device (ioctl) reports ILLEGAL REQUEST. Dec 28 14:13:30 linux kernel: SCSI device sda: 234493056 512-byte hdwr sectors (120060 MB) Dec 28 14:13:30 linux kernel: sda: test WP failed, assume Write Enabled Dec 28 14:13:30 linux kernel: sda: I/O error: dev 08:00, sector 0 Dec 28 14:13:30 linux kernel: I/O error: dev 08:00, sector 0 Dec 28 14:13:30 linux kernel: unable to read partition table Dec 28 14:13:30 linux kernel: I/O error: dev 08:00, sector 0 Dec 28 14:13:30 linux /etc/hotplug/usb.agent[1847]: Can't ignore signal CHLD, forcing to default. Dec 28 14:13:31 linux kernel: SCSI device (ioctl) reports ILLEGAL REQUEST. Dec 28 14:13:31 linux kernel: SCSI device sda: 234493056 512-byte hdwr sectors (120060 MB) Dec 28 14:13:31 linux kernel: sda: test WP failed, assume Write Enabled Dec 28 14:13:31 linux kernel: sda: I/O error: dev 08:00, sector 0 Dec 28 14:13:31 linux kernel: I/O error: dev 08:00, sector 0 Dec 28 14:13:31 linux kernel: unable to read partition table Dec 28 14:13:31 linux kernel: I/O error: dev 08:00, sector 0 Dec 28 14:13:31 linux kernel: I/O error: dev 08:00, sector 0 Die Platte läßt sich weder mounten, noch kann man mit dd auf sda1 oder direkt auf sda zugreifen. Wie gesagt, partitioniert und formatiert ist die platte, geht unter XP wunderbar. Gruß und einen guten Jahreswechsel Stefan -- Stefan Jansen *** E-Mail: stefan.jansen@gmx.de Internet: http://sjansen.webhop.org
Hi! On Di, Dez 28, 2004 at 02:29:43 +0100, Stefan Jansen wrote:
Ich habe eine IDE-Platte mit 120GB in ein Gehäuse eingebaut und das per USB angeschlosen. Kernel 2.4.19, SuSE 8.1.
Erkannt wird die Platte ja... Kannst du mal probieren, ob ein
fdisk -l /dev/sda
was ausspuckt? Evtl. würde dir auch ein neuerer 2.4er Kernel
weiterelfen, keine Ahnung :-(.
--
Gruß,
Christian Schöpplein
Hallo Stefan,
Die Platte läßt sich weder mounten, noch kann man mit dd auf sda1 oder direkt auf sda zugreifen.
Wie gesagt, partitioniert und formatiert ist die platte, geht unter XP wunderbar.
bei 120GB und nur einer Partition tippe ich mal auf eine NTFS-Partition. Kann es sein, dass dein Kernel NTFS-Lesen noch nicht freigeschaltet hat? Dass das Schreiben mit einem derartig alten Kernel Probleme macht ist an- zunehmen, aber zumindest das Lesen sollte funktionieren. Was mich wundert ist, dass auch dd nicht geht... Was sagt denn fdisk -l /dev/sda ? Viele Grüße Michael
Hallo, ich hatte versehentlich dieses Thema in suse-blinux anstatt suse-linux gepostet. Ich bitte deshalb erst mal um Entschuldigung. Die Diskussion wird also in suse-linux weitergeführt. Gruß Stefan -- Stefan Jansen *** E-Mail: stefan.jansen@gmx.de Internet: http://sjansen.webhop.org
participants (3)
-
Christian Schoepplein
-
Michael Zacherle
-
Stefan Jansen