Hi, it is the same error code, but for me it is the partition containing the sources (the SLES CDs) that autoyast tries to mount. -----Ursprüngliche Nachricht----- Von: Niall Calvert [mailto:niall@calvert.cn] Gesendet: Freitag, 22. September 2006 18:29 An: Wenk, Moritz; suse-autoinstall@suse.com Betreff: RE: [suse-autoinstall] SLES 10 and disk to disk autoyast installation I've also been trying also to get disk-to-disk install working, also with EVMS volumes; do you get a similar error message to the following: Failure occurred during following action: Mount /dev/sda1 to /boot System error code was -3003 mount -t reiserfs /dev/sda1 /mnt/boot mount: /dev/sda1 already mounted or /mnt/boot busy Best regards Niall -----Original Message----- From: Wenk, Moritz [mailto:Moritz.Wenk@maxdata.com] Sent: 22 September 2006 14:15 To: suse-autoinstall@suse.com Subject: [suse-autoinstall] SLES 10 and disk to disk autoyast installation Hello, I am trying to autoinstall SLES 10 in HD mode (disk to disk). It worked for SLES 9 but does not any longer with SLES 10. The problem is that YaST tries to mount my source partition when formating the other partitions and this fails because the source partition is alerady mounted. This is my partition schema: sda1: ext3 16GB sda2: swap sda3: fat32 16BG The third partition does contain the installation source. This is the autoyast partition plan: <partitioning config:type="list"> <drive> <device>/dev/sda</device> <initialize config:type="boolean">false</initialize> <is_evms_vg config:type="boolean">false</is_evms_vg> <is_lvm_vg config:type="boolean">false</is_lvm_vg> <use>1,2</use> <partitions config:type="list"> <partition> <create config:type="boolean">false</create> <format config:type="boolean">true</format> <filesystem config:type="symbol">ext3</filesystem> <fsopt>defaults,acl</fsopt> <loop_fs config:type="boolean">false</loop_fs> <mount>/</mount> <partition_id config:type="integer">131</partition_id> <partition_nr config:type="integer">1</partition_nr> <size>16gb</size> </partition> <partition> <create config:type="boolean">false</create> <format config:type="boolean">true</format> <filesystem config:type="symbol">swap</filesystem> <loop_fs config:type="boolean">false</loop_fs> <mount>swap</mount> <partition_id config:type="integer">130</partition_id> <partition_nr config:type="integer">2</partition_nr> <size>512mb</size> </partition> </partitions> </drive> </partitioning> And the kernel command line for autoyast: install=hd://sda3/suse AutoYaST=file:///autoyast.xml The autoyast file (autoyast.xml) is contained in the initrd. Kernel and initrd are booted from sda3. This worked for SLES 9 with a little trick (unmounting /mounts/extra in a pre-install script). Any ideas how to get the disk to disk autoyast installation working for SLES 10? Regards, i. A. Moritz Wenk Specialist Product Engineering & Development Corporate Technology Software MAXDATA Systeme GmbH Elbestraße 12-16 D-45768 Marl Telefon: +49 (0) 2365 952-2715 Telefax: +49 (0) 2365 952-2279 E-Mail : moritz.wenk@maxdata.de http://www.maxdata.com -- To unsubscribe, e-mail: suse-autoinstall-unsubscribe@suse.com For additional commands, e-mail: suse-autoinstall-help@suse.com