[opensuse-arm] tumbleweed on RPi Zero W
Hi all, Yesterday I tried openSUSE Tumbleweed image on my RPi Zero W (v1.1) with JeOS image. I was able to boot into grub but didn't see any output from the kernel on the serial console. I saw that console was set to ttyAMA0, I tried also with ttyS0 and ttyS1, as well as with earlycon as described in [1]. But no luck. Was anyone able to boot the newest [2] RPi tumbleweed image just using the serial console, or do I need a monitor on the firstboot? Regards, Matthias [1] https://en.opensuse.org/HCL:Raspberry_Pi [2] openSUSE-Tumbleweed-ARM-JeOS-raspberrypi.armv6l-2019.10.25-Snapshot20191101.raw.xz -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org
Hi Matthias,
-----Original Message----- From: Matthias Brugger
Sent: 07 November 2019 10:33 To: Mailinglist openSUSE ARM Cc: ralph.gauer@bwc-illmensee.de; Michael Ströder ; Freek de Kruijf Subject: [opensuse-arm] tumbleweed on RPi Zero W Hi all,
Yesterday I tried openSUSE Tumbleweed image on my RPi Zero W (v1.1) with JeOS image. I was able to boot into grub but didn't see any output from the kernel on the serial console. I saw that console was set to ttyAMA0, I tried also with ttyS0 and ttyS1, as well as with earlycon as described in [1]. But no luck.
Was anyone able to boot the newest [2] RPi tumbleweed image just using the serial console, or do I need a monitor on the firstboot?
No, you should be able to boot it with serial only. I tried this image on a RPi1, with serial and HDMI connected and I have nothing after grub loaded kernel and initrd. Cheers, Guillaume
Regards, Matthias
[1] https://en.opensuse.org/HCL:Raspberry_Pi [2] openSUSE-Tumbleweed-ARM-JeOS-raspberrypi.armv6l-2019.10.25- Snapshot20191101.raw.xz -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org
IMPORTANT NOTICE: The contents of this email and any attachments are confidential and may also be privileged. If you are not the intended recipient, please notify the sender immediately and do not disclose the contents to any other person, use it for any purpose, or store or copy the information in any medium. Thank you. N�����r��y隊Z)z{.�櫛맲��r��z�^�ˬz��N�(�֜��^� ޭ隊Z)z{.�櫛�0�����Ǩ�
As far as I remember there is a ticket in the bugzilla according generic armv6 faluire. 07.11.2019 13:20, Guillaume Gardet пишет:
Hi Matthias,
-----Original Message----- From: Matthias Brugger
Sent: 07 November 2019 10:33 To: Mailinglist openSUSE ARM Cc: ralph.gauer@bwc-illmensee.de; Michael Ströder ; Freek de Kruijf Subject: [opensuse-arm] tumbleweed on RPi Zero W Hi all,
Yesterday I tried openSUSE Tumbleweed image on my RPi Zero W (v1.1) with JeOS image. I was able to boot into grub but didn't see any output from the kernel on the serial console. I saw that console was set to ttyAMA0, I tried also with ttyS0 and ttyS1, as well as with earlycon as described in [1]. But no luck.
Was anyone able to boot the newest [2] RPi tumbleweed image just using the serial console, or do I need a monitor on the firstboot?
No, you should be able to boot it with serial only.
I tried this image on a RPi1, with serial and HDMI connected and I have nothing after grub loaded kernel and initrd.
Cheers, Guillaume
Regards, Matthias
[1] https://en.opensuse.org/HCL:Raspberry_Pi [2] openSUSE-Tumbleweed-ARM-JeOS-raspberrypi.armv6l-2019.10.25- Snapshot20191101.raw.xz -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org
IMPORTANT NOTICE: The contents of this email and any attachments are confidential and may also be privileged. If you are not the intended recipient, please notify the sender immediately and do not disclose the contents to any other person, use it for any purpose, or store or copy the information in any medium. Thank you.
-- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org
-----Original Message----- From: Matwey V. Kornilov
Sent: 07 November 2019 13:46 To: opensuse-arm@opensuse.org Subject: [opensuse-arm] Re: tumbleweed on RPi Zero W As far as I remember there is a ticket in the bugzilla according generic armv6 faluire.
If you are referencing https://bugzilla.opensuse.org/show_bug.cgi?id=1145646 this is not the problem here since we still use grub 2.02. Or is there another bug? Guillaume
Hi Matthias,
-----Original Message----- From: Matthias Brugger
Sent: 07 November 2019 10:33 To: Mailinglist openSUSE ARM Cc: ralph.gauer@bwc-illmensee.de; Michael Ströder ; Freek de Kruijf Subject: [opensuse-arm] tumbleweed on RPi Zero W Hi all,
Yesterday I tried openSUSE Tumbleweed image on my RPi Zero W (v1.1) with JeOS image. I was able to boot into grub but didn't see any output from the kernel on the serial console. I saw that console was set to ttyAMA0, I tried also with ttyS0 and ttyS1, as well as with earlycon as described in [1]. But no luck.
Was anyone able to boot the newest [2] RPi tumbleweed image just using the serial console, or do I need a monitor on the firstboot?
No, you should be able to boot it with serial only.
I tried this image on a RPi1, with serial and HDMI connected and I have nothing after grub loaded kernel and initrd.
Cheers, Guillaume
Regards, Matthias
[1] https://en.opensuse.org/HCL:Raspberry_Pi [2] openSUSE-Tumbleweed-ARM-JeOS-raspberrypi.armv6l-2019.10.25- Snapshot20191101.raw.xz -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org
IMPORTANT NOTICE: The contents of this email and any attachments are confidential and may also be privileged. If you are not the intended recipient,
07.11.2019 13:20, Guillaume Gardet пишет: please notify the sender immediately and do not disclose the contents to any other person, use it for any purpose, or store or copy the information in any medium. Thank you.
-- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org
IMPORTANT NOTICE: The contents of this email and any attachments are confidential and may also be privileged. If you are not the intended recipient, please notify the sender immediately and do not disclose the contents to any other person, use it for any purpose, or store or copy the information in any medium. Thank you.
07.11.2019 15:48, Guillaume Gardet пишет:
-----Original Message----- From: Matwey V. Kornilov
Sent: 07 November 2019 13:46 To: opensuse-arm@opensuse.org Subject: [opensuse-arm] Re: tumbleweed on RPi Zero W As far as I remember there is a ticket in the bugzilla according generic armv6 faluire.
If you are referencing https://bugzilla.opensuse.org/show_bug.cgi?id=1145646 this is not the problem here since we still use grub 2.02. Or is there another bug?
Ah, sorry. You are right.
Guillaume
Hi Matthias,
-----Original Message----- From: Matthias Brugger
Sent: 07 November 2019 10:33 To: Mailinglist openSUSE ARM Cc: ralph.gauer@bwc-illmensee.de; Michael Ströder ; Freek de Kruijf Subject: [opensuse-arm] tumbleweed on RPi Zero W Hi all,
Yesterday I tried openSUSE Tumbleweed image on my RPi Zero W (v1.1) with JeOS image. I was able to boot into grub but didn't see any output from the kernel on the serial console. I saw that console was set to ttyAMA0, I tried also with ttyS0 and ttyS1, as well as with earlycon as described in [1]. But no luck.
Was anyone able to boot the newest [2] RPi tumbleweed image just using the serial console, or do I need a monitor on the firstboot?
No, you should be able to boot it with serial only.
I tried this image on a RPi1, with serial and HDMI connected and I have nothing after grub loaded kernel and initrd.
Cheers, Guillaume
Regards, Matthias
[1] https://en.opensuse.org/HCL:Raspberry_Pi [2] openSUSE-Tumbleweed-ARM-JeOS-raspberrypi.armv6l-2019.10.25- Snapshot20191101.raw.xz -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org
IMPORTANT NOTICE: The contents of this email and any attachments are confidential and may also be privileged. If you are not the intended recipient,
07.11.2019 13:20, Guillaume Gardet пишет: please notify the sender immediately and do not disclose the contents to any other person, use it for any purpose, or store or copy the information in any medium. Thank you.
-- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org
IMPORTANT NOTICE: The contents of this email and any attachments are confidential and may also be privileged. If you are not the intended recipient, please notify the sender immediately and do not disclose the contents to any other person, use it for any purpose, or store or copy the information in any medium. Thank you.
-- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org
participants (3)
-
Guillaume Gardet
-
Matthias Brugger
-
Matwey V. Kornilov