Hi, I am trying to run openSUSE-Tumbleweed-ARM-JeOS-efi.armv7l-2017.10.29-Build1.7.raw using qemu. When I use qemu-system-aarch64 with 64-bit UEFI code aavmf-aarch64-code.bin then the only I see is the EFI console: UEFI Interactive Shell v2.287477C2-69C7-11D2-8E39-00A0C969723B B8F1C820 EDK IIlProtocolInterface: 752F3136-4E16-4FDC-A22A-E5F46812F4CA B8F1FF18 UEFI v2.60 (EDK II, 0x00010000)008-7F9B-4F30-87AC-60C9FEF5DA4E B8348710 Mapping table FS0: Alias(s):HD1a0b:;BLK2: VenHw(837DCA9E-E874-4D82-B29A-23FE0E23D1E2,003E000A00000000)/Scsi(0x0,0x0)/HD(1,GPT,E30D92E4-F475-4D50-9D3D-DF05DA812008,0x800,0x64004) BLK5: Alias(s): VenHw(F9B94AE2-8BA6-409B-9D56-B9B417F53CB3) BLK0: Alias(s): VenHw(8047DB4B-7E9C-4C0C-8EBC-DFBBAACACE8F) BLK1: Alias(s): VenHw(837DCA9E-E874-4D82-B29A-23FE0E23D1E2,003E000A00000000)/Scsi(0x0,0x0) BLK3: Alias(s): VenHw(837DCA9E-E874-4D82-B29A-23FE0E23D1E2,003E000A00000000)/Scsi(0x0,0x0)/HD(2,GPT,3DF8DD35-94BC-4FF0-B74C-12853D4B1811,0x65000,0x83004) BLK4: Alias(s): VenHw(837DCA9E-E874-4D82-B29A-23FE0E23D1E2,003E000A00000000)/Scsi(0x0,0x0)/HD(3,GPT,38C4AA8C-4A7F-49C4-BCFD-6C2C755496BD,0xE8800,0x3DE781) Press ESC in 1 seconds to skip startup.nsh or any other key to continue. FSOpen: Open '\startup.nsh' Success FSOpen: Open '\startup.nsh' Success FSOpen: Open '\startup.nsh' Success Shell> bootarm FSOpen: Open '\efi\boot\bootarm.EFI' Success FSOpen: Open '\efi\boot\bootarm.EFI' Success FSOpen: Open '\efi\boot\bootarm.EFI' Success FSOpen: Open '\efi\boot\bootarm.EFI' Success [Security] 3rd party image[0] can be loaded after EndOfDxe: VenHw(837DCA9E-E874-4D82-B29A-23FE0E23D1E2,003E000A00000000)/Scsi(0x0,0x0)/HD(1,GPT,E30D92E4-F475-4D50-9D3D-DF05DA812008,0x800,0x64004)/\efi\boot\bootarm.EFI. InstallProtocolInterface: 5B1B31A1-9562-11D2-8E3F-00A0C969723B B8EDE440 Unloading driver at 0x00000000000 Shell> Error Status: Unsupported (line number 1) As far as I understand, 64-bit Qemu UEFI code doesn't expect to see and run 32-bit EFI executable. When I try to use qemu-uefi-aarch32.bin as firmware, then I see the following: Initialization of device cfi.pflash01 failed: failed to read the initial flash content As far as I understand, qemu-uefi-aarch32.bin is in wrong format, but there are no other files in ovfm rpm package. What is the proper way to run JeOS-efi.armv7? Is it supposed to work in qemu? -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org