Hello, On 03/27/2013 09:20 AM, Dirk Müller wrote:
Efikamx (not recently tested),
I tested it now from http://download.opensuse.org/ports/armv7hl/distribution/12.3/images/openSUSE... and I get on the serial console: U-Boot 2009.01-2.0.6-efikamx (Nov 02 2010 - 17:13:53) CPU: Freescale i.MX51 family 3.0V at 800 MHz mx51 pll1: 800MHz mx51 pll2: 665MHz mx51 pll3: 216MHz ipg clock : 66500000Hz ipg per clock : 665000000Hz uart clock : 66500000Hz cspi clock : 54000000Hz Board: MX51 Efika MX 3.0 [WDOG] DRAM: 512 MB JEDEC ID: 0xbf:0x25:0x4a Reading SPI NOR flash 0x40000 [0x10000 bytes] -> ram 0x975f06e8 .SUCCESS *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial board id: 1.0.1, rev1.3 Boot Source: SPI NOR FLASH BOOT Boot Cmd: for device in "mmc ide"; do if strcmp ${device} == mmc; then; mmcinit; setenv units "0 1"; else; setenv units "0"; fi; for interface in ${units}; do if strcmp ${device} == mmc; then mmcprobe ${interface}; else; ide reset; fi; for fs in "ext2 fat"; do setenv loadcmd "${fs}load ${device} 0:1"; if ${loadcmd} ${scriptaddr} boot.scr; then; if imi ${scriptaddr}; then; autoscr ${scriptaddr}; fi; fi; done; done; done; Hit any key to stop autoboot: 0 SD card. Vendor: Man 02 OEM TM "SA04G" Date 11/2009 Product: 2622955146 Revision: 0.4 SD card. Vendor: Man 02 OEM TM "SA04G" Date 11/2009 Product: 2622955146 Revision: 0.4 MMC interface 0 selected 641 bytes read ## Checking Image at 91000000 ... Legacy image found Image Name: Boot-Script Image Type: ARM Linux Script (uncompressed) Data Size: 577 Bytes = 0.6 kB Load Address: 00000000 Entry Point: 00000000 Contents: Image 0: 569 Bytes = 0.6 kB Verifying Checksum ... OK ## Executing script at 91000000 kerneladdr=0x90007FC0 ramdiskaddr=0x92000000 3455912 bytes read 35310835 bytes read ## Booting kernel from Legacy Image at 90007fc0 ... Image Name: Linux-3.7.10-1.1-imx51 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3455848 Bytes = 3.3 MB Load Address: 90008000 Entry Point: 90008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 92000000 ... Image Name: Initrd Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 35310771 Bytes = 33.7 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Error: unrecognized/unsupported machine ID (r1 = 0x00000920). Available machine support: ID (hex) NAME 0000084d Freescale MX51 Babbage Board 000006a0 Freescale MX51 3-Stack Board 00000b06 Eukrea CPUIMX51SD ffffffff Freescale i.MX51 (Device Tree Support) Please check your kernel config and/or bootloader. Bye, CzP -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org