On 21/04/17 15:40, Andreas F�rber wrote:
Hi Sid,
Am 21.04.2017 um 16:13 schrieb Sid Boyce:
On 21/04/17 09:13, Andreas Färber wrote:
JeOS-odroidc2 is now bootable - available from Contrib:OdroidC2, instructions at https://en.opensuse.org/HCL:OdroidC2.
Hi Andreas, Burned openSUSE-Tumbleweed-ARM-JeOS-odroidc2.aarch64-2017.04.21-Build3.1.raw.xz per instructions, does not boot. Only the red LED lights. It does here. Are you maybe looking at an HDMI screen instead of serial? HDMI drivers will come in 4.12, and currently there are no Odroid-C2 DT patches yet. Booting does not mean full-featured!
Also as usual it takes some minutes until Kiwi has repartitioned the card and network is up.
On my home branch, before submitting JeOS, I had verified that also second boot works, thanks to the dracut config added.
Regards, Andreas
GXBB:BL1:08dafd:0a8993;FEAT:EDFC318C;POC:3;RCY:0;EMMC:800;NAND:81;SD:0;READ:0;CHK:0; TE: 312955 no sdio debug board detected
BL2 Built : 11:44:26, Nov 25 2015. gxb gfb13a3b-c2 - jcao@wonton
Board ID = 8 set vcck to 1100 mv set vddee to 1050 mv CPU clk: 1536MHz DDR channel setting: DDR0 Rank0+1 same DDR0: 2048MB(auto) @ 912MHz(2T)-13 DataBus test pass! AddrBus test pass! Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x000000b0 Load bl30 from SD, src: 0x00010200, des: 0x01000000, size: 0x00009ef0 Sending bl30........................................OK. Run bl30... Load bl301 from SD, src: 0x0001c200, des: 0x01000000, size: 0x000018c0 Wait bl30...Done Sending bl301.......OK. Run bl301... 0, des: 0x10100000, size: 0x00011130
--- UART initialized after reboot --- [Reset cause: unknown] [Image: unknown, amlogic_v1.1.3046-00db630-dirty 2016-08-31 09:24:14 tao.zeng@droid04] bl30: check_permit, count is 1 bl30: check_permit: ok! chipid: ef be ad de d f0 ad ba ef bLoad bl33 from SD, src: 0x00034200, des: 0x01000000, size: 0x00055b50 e ad de not ES chip [0.427617 Inits done] secure task start! high task start! low task start! NOTICE: BL3-1: v1.0(debug):4d2e34d NOTICE: BL3-1: Built : 17:08:35, Oct 29 2015 INFO: BL3-1: Initializing runtime services INFO: BL3-1: Preparing for EL3 exit to normal world INFO: BL3-1: Next image address = 0x1000000 INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2017.05-rc2 (Apr 21 2017 - 03:45:10 +0000) odroid-c2
DRAM: 2 GiB MMC: mmc@72000: 0, mmc@74000: 1 Using default environment
In: serial@4c0 Out: serial@4c0 Err: serial@4c0 Net: eth0: ethernet@c9410000 Hit any key to stop autoboot: 0 => boot switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... 19109 bytes read in 28 ms (666 KiB/s) Found EFI removable media binary efi/boot/bootaa64.efi reading efi/boot/bootaa64.efi 731648 bytes read in 37 ms (18.9 MiB/s) ## Starting EFI application at 01080000 ... Scanning disk mmc@72000.blk... Card did not respond to voltage select! mmc_init: -95, time 10 Found 1 disks Welcome to GRUB!
error: terminal `gfxterm' isn't found. error: no suitable video mode found. error: can't find command `terminal'.
GNU GRUB version 2.02~rc2
┌────────────────────────────────────────────────────────────────────────────┐ │ openSUSE [ VMX ] │ │*Failsafe -- openSUSE [ VMX ] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ └────────────────────────────────────────────────────────────────────────────┘
Use the ▲ and ▼ keys to select which entry is highlighted. Press enter to boot the selected OS, `e' to edit the commands before booting or `c' for a command-line.
Hi Andreas, I have both the serial console on /dev/ttyUSB0 and HDMI screens connected. The blue LED never flashes on and no message appears on the serial connection. I am using one of the recommended Toshiba SD cards - 64 GB. Regards Sid. -- Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support Senior Staff Specialist, Cricket Coach Microsoft Windows Free Zone - Linux used for all Computing Tasks -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org