12.02.2020 18:37, ITwrx пишет:
On 2/12/20 8:59 AM, ITwrx wrote:
Hi,
It is very strange to hear that. I deployed this image to couple of Rock64-s week ago. So, could you please be more specific? What are you trying to do exactly?
You are supposed to download openSUSE-Tumbleweed-ARM-JeOS-rock64.aarch64-2020.01.30-Build5.29.raw.xz uncompress it with `xz -d openSUSE-Tumbleweed-ARM-JeOS-rock64.aarch64-2020.01.30-Build5.29.raw.xz` and write .raw file to microsd card as the following `dd_rescue openSUSE-Tumbleweed-ARM-JeOS-rock64.aarch64-2020.01.30-Build5.29.raw /dev/your_sd_card_here`. That's what i did, but i'll try it again. I didn't get any errors when writing the image. This time, i'll wipe the sd card and create one fat
On 2/12/20 1:49 AM, Matwey V. Kornilov wrote: partition, just to be on the safe side.
Do you have usb rs232 ttl converter to attach the Rock64 console? What does it say? i did, but i don't remember. It didn't get very far. If it fails this time, i'll copy and paste the output.
Thanks
ср, 12 февр. 2020 г. в 10:17, Guillaume Gardet <Guillaume.Gardet@arm.com>:
Hi,
-----Original Message----- From: ITwrx <info@itwrx.org> Sent: 12 February 2020 03:49 To: opensuse-arm@opensuse.org Subject: [opensuse-arm] Rock64
Thorston/All,
i just wanted to report that there are not Rock64 microOS images, only images for the older pine64.
Also, the instructions on the Rock64 openSUSE wiki don't work (exactly as they are), using the below linked image file. I don't know what the corresponding "packages" file is for or how to use it, so it was not used in any way. The Rock64 The "packages" file is just the list of installed packages in this *.raw.xz image.
openSUSE wiki page didn't mention anything about it. Probably why the board won't boot... :)
http://download.opensuse.org/repositories/devel:/ARM:/Factory:/Contrib:/Roc kchip/images/openSUSE-Tumbleweed-ARM-JeOS-rock64.aarch64-2020.01.30- Build5.29.raw.xz
Any tips appreciated. Added Matwey in Cc who may help.
Cheers, Guillaume
Thanks,
ITwrx
-- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org
Ok, i misspoke earlier. The first time i didn't extract, then run dd_rescue per your instructions. i ran "xzcat [image].raw.xz | dd bs=4M of=/dev/sdX iflag=fullblock oflag=direct; sync" (substituting relevant info) per the wiki. This time i did use your commands. I got the same result and output in the serial console as before.
U-Boot TPL 2020.01 (Jan 30 2020 - 10:43:44) data training error col error data training error LPDDR3, 800MHz BW=16 Col=12 Bk=8 CS0 Row=16 CS=1 Die BW=8 Size=4096MB I don't know much about Arm, so i don't know what that output means. :)
It is very first stage of bootloader. Do you see anything else next?
Thanks
-- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org