Re: [suse-amd64] CPU runs only with 800 MHz
The Hardware is: CPU: Athlon64 3000+ Board: MSI K8T Neo Bios is the newest. In /var/log/messages there are following details: rcpowersaved: CPU frequency scaling is not supported by your processor. rcpowersaved: enter 'POWERSACE_CPUFREQD_MODULE=off' in /etc/sysconfig/powersave/common to avoid this warning. in /var/log/boot.log there are no entys In Windows the cpu runs at 1000mhz when there is no load and the vcore is reduced as well. so far so good... Is there a possibility to configure manually that frequency scaling is possible? Or are there any other solutions? The powersaving feature is nice for me because next month I want to set up 100 athlon64 systems. And then saving power saves money... :) Thanks for your help! Thomas
Thomas Köhler <sorcerer@counterstrike.de> writes:
The Hardware is:
CPU: Athlon64 3000+ Board: MSI K8T Neo Bios is the newest.
In /var/log/messages there are following details:
rcpowersaved: CPU frequency scaling is not supported by your processor. rcpowersaved: enter 'POWERSACE_CPUFREQD_MODULE=off' in /etc/sysconfig/powersave/common to avoid this warning.
What else is there? Any lines before that? Please send also the output of /proc/cpuinfo
in /var/log/boot.log there are no entys
In Windows the cpu runs at 1000mhz when there is no load and the vcore is reduced as well.
so far so good... Is there a possibility to configure manually that frequency scaling is possible? Or are there any other solutions?
The powersaving feature is nice for me because next month I want to set up 100 athlon64 systems. And then saving power saves money... :)
Yep, Andreas -- Andreas Jaeger, aj@suse.de, http://www.suse.de/~aj SUSE Linux AG, Maxfeldstr. 5, 90409 Nürnberg, Germany GPG fingerprint = 93A3 365E CE47 B889 DF7F FED1 389A 563C C272 A126
Hi, here the requested logfiles: Important lines from /var/log/messages May 11 17:17:31 amd64 syslogd 1.4.1: restart. May 11 17:17:32 amd64 rcpowersaved: CPU frequency scaling is not supported by your processor. May 11 17:17:32 amd64 rcpowersaved: enter 'POWERSAVE_CPUFREQD_MODULE=off' in /etc/sysconfig/powersave/common to avoid this warning. May 11 17:17:32 amd64 [powersaved][3273]: WARNING in Function ACPI_Interface; line 26: could not set battery alarm, you may need to force polling mode. May 11 17:17:32 amd64 [powersaved][3273]: resmgr: server response code 200 amd64:~ # cat /proc/cpuinfo processor : 0 vendor_id : AuthenticAMD cpu family : 15 model : 12 model name : AMD Athlon(tm) 64 Processor 3000+ stepping : 0 cpu MHz : 2000.090 cache size : 512 KB fpu : yes fpu_exception : yes cpuid level : 1 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext lm 3dnowext 3dnow bogomips : 3932.16 TLB size : 1088 4K pages clflush size : 64 address sizes : 40 bits physical, 48 bits virtual power management: ts fid vid ttp hope there will be a solution :)Thomas
On Tue, May 11, 2004 at 05:47:00PM +0200, Thomas K?hler wrote:
Looks like an Opteron or FX!5x. Those do not support C'n'Q; only Athlon 64 does.
-Andi
No, its an Athlon64 3000+ and cool and quiet works in windows.
What did the powernow-k8 kernel driver say in dmesg ? -Andi
What did the powernow-k8 kernel driver say in dmesg ?
Nothing. Is that driver included in the standard Suse 9.1 Setup? (I installed the 64bit version from dvd)
Is it stated that your mainboard BIOS has full Newcastle support ? Or that your mainboard is suitable for CG stepping processors ?
the Bios is the newset version 1.6 from msi (updated today). I think it supports this processors... Also C'n'Q is working in windows like I said. On the Webpage msi gives the information that the Board supports Athlon64 till 3400+ max.
On Tue, May 11, 2004 at 06:14:42PM +0200, Thomas K?hler wrote:
What did the powernow-k8 kernel driver say in dmesg ?
Nothing. Is that driver included in the standard Suse 9.1 Setup? (I installed the 64bit version from dvd)
powersaved should have tried to load it before outputting the message you posted earlier. Do modprobe powernow_k8 dmesg | grep powernow and post the output. -Andi
I had a similar problem with my laptop (AMD64 3200+) running suse 9.0 and 2.4 kernel. It appeared that the manufacture hadn't provided a correct PST table in the BIOS. I had to resort to drastic measures by hacking the powernow-k8 module to provide the correct vid and fid for full speed. A bit of a potch and the machine only has two speeds of 800MHz and 2000MHz. In Windows the speed varies more or less continuously. I don't mind since I'm either editing files (ok at 800 MHz) or running simulations (ok at 2000MHz). I'm not sure about suse 9.1 and the 2.6 kernel since that uses ACPI. On Tuesday 11 May 2004 16:52, Andi Kleen wrote:
On Tue, May 11, 2004 at 05:47:00PM +0200, Thomas K?hler wrote:
Looks like an Opteron or FX!5x. Those do not support C'n'Q; only Athlon 64 does.
-Andi
No, its an Athlon64 3000+ and cool and quiet works in windows.
What did the powernow-k8 kernel driver say in dmesg ?
-Andi
-- Jonathan Breeze Research Fellow Centre for Physical Electronics and Materials London South Bank University 103 Borough Road London SE1 0AA Tel: +44(0)20 7815 7582 Fax: +44(0)20 7815 7599
Thomas Köhler <sorcerer@counterstrike.de> writes:
The Hardware is:
CPU: Athlon64 3000+ Board: MSI K8T Neo Bios is the newest.
In /var/log/messages there are following details:
rcpowersaved: CPU frequency scaling is not supported by your processor. rcpowersaved: enter 'POWERSACE_CPUFREQD_MODULE=off' in /etc/sysconfig/powersave/common to avoid this warning.
in /var/log/boot.log there are no entys
And what's in /var/log/boot.msg? Send the whole file. Btw. please also send the contents of /proc/cmdline, Andreas -- Andreas Jaeger, aj@suse.de, http://www.suse.de/~aj SUSE Linux AG, Maxfeldstr. 5, 90409 Nürnberg, Germany GPG fingerprint = 93A3 365E CE47 B889 DF7F FED1 389A 563C C272 A126
Ok, here output vom /var/log/boot.msg and at the bottom /proc/cmdline Hope this will help... amd64:~ # cat /var/log/boot.msg Inspecting /boot/System.map-2.6.4-52-default Loaded 23391 symbols from /boot/System.map-2.6.4-52-default. Symbols match kernel version 2.6.4. No module symbols loaded - kernel modules not enabled. klogd 1.4.1, log source = ksyslog started. <4>Bootdata ok (command line is auto BOOT_IMAGE=Linux root=2103 splash=silent console=tty0 desktop resume=/dev/hde5 showopts) <4>Linux version 2.6.4-52-default (geeko@buildhost) (gcc version 3.3.3 (SuSE Linux)) #1 Wed Apr 7 02:15:23 UTC 2004 <6>BIOS-provided physical RAM map: <4> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) <4> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) <4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) <4> BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) <4> BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data) <4> BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS) <4> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) <4> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) <4> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) <7>ACPI: have wakeup address 0x10000001000 <6>No mptable found. <6>No mptable found. <4>On node 0 totalpages: 262128 <4> DMA zone: 4096 pages, LIFO batch:1 <4> Normal zone: 258032 pages, LIFO batch:16 <4> HighMem zone: 0 pages, LIFO batch:1 <6>PCI bridge 00:01 from 1106 found. Setting "noapic". Overwrite with "apic" <6>ACPI: RSDP (v000 AMI ) @ 0x00000000000fa3f0 <6>ACPI: RSDT (v001 AMIINT VIA_K8 0x00000010 MSFT 0x00000097) @ 0x000000003fff0000 <6>ACPI: FADT (v001 AMIINT VIA_K8 0x00000011 MSFT 0x00000097) @ 0x000000003fff0030 <6>ACPI: MADT (v001 AMIINT VIA_K8 0x00000009 MSFT 0x00000097) @ 0x000000003fff00c0 <6>ACPI: DSDT (v001 VIA VIA_K8 0x00001000 MSFT 0x0100000d) @ 0x0000000000000000 <7>ACPI: Local APIC address 0xfee00000 <6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) <6>Processor #0 15:12 APIC version 16 <6>ACPI: Skipping IOAPIC probe due to 'noapic' option. <6>Using ACPI for processor (LAPIC) configuration information <4>Intel MultiProcessor Specification v1.4 <6> Virtual Wire compatibility mode. <6>OEM ID: VIA <6>Product ID: K8T400 <6>APIC at: 0xFEE00000 <4>I/O APIC #2 Version 3 at 0xFEC00000. <6>Processors: 1 <4>Checking aperture... <4>CPU 0: aperture @ d0000000 size 128 MB <4>Built 1 zonelists <4>Kernel command line: auto BOOT_IMAGE=Linux root=2103 splash=silent console=tty0 desktop resume=/dev/hde5 showopts <6>bootsplash: silent mode. <4>Initializing CPU#0 <4>PID hash table entries: 16 (order 4: 256 bytes) <4>CKRM Initialized <6>time.c: Using 1.193182 MHz PIT timer. <6>time.c: Detected 2000.148 MHz processor. <4>Console: colour dummy device 80x25 <4>Memory: 1027996k/1048512k available (2166k kernel code, 19724k reserved, 848k data, 172k init) <4>Calibrating delay loop... 3940.35 BogoMIPS <6>Security Scaffold v1.0.0 initialized <6>SELinux: Initializing. <6>SELinux: Starting in permissive mode <6>There is already a security framework initialized, register_security failed. <6>Failure registering capabilities with the kernel <6>selinux_register_security: Registering secondary module capability <6>Capability LSM initialized <6>Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) <4>Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) <4>Mount-cache hash table entries: 256 (order: 0, 4096 bytes) <6>checking if image is initramfs...it isn't (no cpio magic); looks like an initrd <6>Looking for DSDT in initrd ...No customized DSDT found in initrd! <6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) <6>CPU: L2 Cache: 512K (64 bytes/line) <4>CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00 <4>POSIX conformance testing by UNIFIX <6>Using local APIC NMI watchdog using perfctr0 <6>Using local APIC timer interrupts. <6>Detected 12.500 MHz APIC timer. <4>do_initcalls <4>init_elf32_binfmt <4>init_elf_binfmt <6>NET: Registered protocol family 16 <6>PCI: Using configuration type 1 <6>mtrr: v2.0 (20020519) <6>ACPI: Subsystem revision 20040326 <6>No customized DSDT found! <4>ACPI: IRQ9 SCI: Edge set to Level Trigger. <6>ACPI: Interpreter enabled <6>ACPI: Using PIC for interrupt routing <6>ACPI: PCI Root Bridge [PCI0] (00:00) <4>PCI: Probing PCI hardware (bus 00) <4> ... the first call_usermodehelper: pci_bus <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] <6>ACPI: Power Resource [URP1] (off) <6>ACPI: Power Resource [URP2] (off) <6>ACPI: Power Resource [FDDP] (off) <6>ACPI: Power Resource [LPTP] (off) <4>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 *12 14 15) <4>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 <4>ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 12 <4>ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 <6>PCI: Using ACPI for IRQ routing <6>PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' <6>agpgart: Detected AGP bridge 0 <6>agpgart: Maximum main memory to use for agp memory: 941M <6>agpgart: AGP aperture is 128M @ 0xd0000000 <6>PCI-DMA: Disabling IOMMU. <6>vesafb: framebuffer at 0xcf000000, mapped to 0xffffff000004d000, size 4096k <6>vesafb: mode is 1280x1024x16, linelength=2560, pages=0 <6>vesafb: scrolling: redraw <6>vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0 <6>fb0: VESA VGA frame buffer device <4>Initial HugeTLB pages allocated: 0 <4>IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ <6>ikconfig 0.7 with /proc/config* <5>VFS: Disk quotas dquot_6.5.1 <6>SELinux: Registering netfilter hooks <6>Initializing Cryptographic API <6>bootsplash 3.1.6-2004/03/31: looking for picture.... silentjpeg size 52139 bytes, does not fit into framebuffer. <4> found (1280x1024, 24562 bytes, v3). <4>Console: switching to colour frame buffer device 147x55 <6>Real Time Clock Driver v1.12 <6>Non-volatile memory driver v1.2 <6>Linux agpgart interface v0.100 (c) Dave Jones <6>Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled <4>ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <4>RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize <6>loop: loaded (max 8 devices) <6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 <6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx <6>VIA8237SATA: IDE controller at PCI slot 0000:00:0f.0 <6>VIA8237SATA: chipset revision 128 <6>VIA8237SATA: 100%% native mode on irq 10 <6> ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:pio, hdb:pio <6> ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:pio, hdd:pio <6>VP_IDE: IDE controller at PCI slot 0000:00:0f.1 <6>VP_IDE: chipset revision 6 <6>VP_IDE: not 100%% native mode: will probe irqs later <6>VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 <6> ide2: BM-DMA at 0xfc00-0xfc07, BIOS settings: hde:DMA, hdf:pio <6> ide3: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdg:pio, hdh:DMA <4>hde: Maxtor 6Y080P0, ATA DISK drive <4>Using anticipatory io scheduler <4>ide2 at 0x1f0-0x1f7,0x3f6 on irq 14 <4>hdh: TOSHIBA DVD-ROM SD-M1612, ATAPI CD/DVD-ROM drive <4>ide3 at 0x170-0x177,0x376 on irq 15 <4>hde: max request size: 128KiB <6>hde: 160086528 sectors (81964 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(133) <6> hde: hde1 hde2 hde3 hde4 < hde5 hde6 > <4>hdh: ATAPI 48X DVD-ROM drive, 512kB Cache <6>Uniform CD-ROM driver Revision: 3.20 <4>ide-floppy driver 0.99.newide <6>mice: PS/2 mouse device common for all mice <6>input: PC Speaker <6>serio: i8042 AUX port at 0x60,0x64 irq 12 <6>serio: i8042 KBD port at 0x60,0x64 irq 1 <6>input: AT Translated Set 2 keyboard on isa0060/serio0 <6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 <6>NET: Registered protocol family 2 <6>IP: routing cache hash table of 8192 buckets, 64Kbytes <6>TCP: Hash tables configured (established 262144 bind 65536) <6>NET: Registered protocol family 1 <4>Resume Machine: resuming from /dev/hde5 <4>Resuming from device hde5 <3>Resume Machine: This is normal swap space <6>ACPI: (supports S0 S1 S4 S5) <6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: ... autorun DONE. <5>RAMDISK: Compressed image found at block 0 <4>VFS: Mounted root (ext2 filesystem). <5>SCSI subsystem initialized <7>libata version 1.02 loaded. <5>ReiserFS: hde3: found reiserfs format "3.6" with standard journal <5>ReiserFS: hde3: using ordered data mode <5>ReiserFS: hde3: journal params: device hde3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 <5>ReiserFS: hde3: checking transaction log (hde3) <5>ReiserFS: hde3: Using r5 hash to sort names <4>VFS: Mounted root (reiserfs filesystem) readonly. <5>Trying to move old root to /initrd ... failed <5>Unmounting old root <5>Trying to free ramdisk memory ... okay <4>Freeing unused kernel memory: 172k freed <6>Adding 2040212k swap on /dev/hde5. Priority:42 extents:1 <6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: ... autorun DONE. <6>device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com <6>NTFS driver 2.1.6 [Flags: R/O MODULE]. <6>NTFS volume version 3.1. <6>subfs 0.9 Kernel logging (ksyslog) stopped. Kernel log daemon terminating. Boot logging started on /dev/tty1(/dev/console) at Tue May 11 19:56:09 2004 <notice>run boot scripts (setserial boot.proc) Configuring serial ports... /dev/ttyS0 at 0x03f8 (irq = 4) is a 16550A Configured serial ports done<notice>exit status of (setserial boot.proc) is (0 0) <notice>run boot scripts (boot.shm) Mounting shared memory FS on /dev/shmdone <notice>exit status of (boot.shm) is (0) <notice>run boot scripts (boot.rootfsck) Activating swap-devices in /etc/fstab... doneFile systems are NOT being checked. <notice>exit status of (boot.rootfsck) is (0) <notice>run boot scripts (boot.md boot.device-mapper) Activating device mapper... Creating /dev/mapper/control character device with major:10 minor:63. done <notice>exit status of (boot.md boot.device-mapper) is (0 0) <notice>run boot scripts (boot.localfs) Checking file systems... fsck 1.34 (25-Jul-2003) doneSetting updone Mounting local file systems... proc on /proc type proc (rw) tmpfs on /dev/shm type tmpfs (rw) devpts on /dev/pts type devpts (rw,mode=0620,gid=5) /dev/hde1 on /windows/C type ntfs (ro,noexec,nosuid,nodev,gid=100,umask=0002,nls=utf8) /dev/hdh on /media/dvd type subfs (ro,nosuid,nodev,fs=cdfss,procuid,iocharset=utf8) /dev/fd0 on /media/floppy type subfs (rw,nosuid,nodev,sync,fs=floppyfss,procuid) done<notice>exit status of (boot.localfs) is (0) <notice>run boot scripts (boot.crypto) <notice>exit status of (boot.crypto) is (0) <notice>run boot scripts (boot.swap boot.scpm boot.restore_permissions boot.loadmodules) Loading required kernel modules doneRestore device permissionsdone Activating remaining swap-devices in /etc/fstab... done<notice>exit status of (boot.swap boot.scpm boot.restore_permissions boot.loadmodules) is (0 0 0 0) <notice>run boot scripts (boot.idedma boot.clock) Setting up the CMOS clockdone <notice>exit status of (boot.idedma boot.clock) is (0 0) <notice>run boot scripts (boot.ldconfig) Setting up timezone datadone <notice>exit status of (boot.ldconfig) is (0) <notice>run boot scripts (boot.sched boot.localnet boot.isapnp) Setting scheduling timeslices unused Setting up hostname 'amd64'done Setting up loopback interface lo lo IP address: 127.0.0.1/8 done <notice>exit status of (boot.sched boot.localnet boot.isapnp) is (6 0 0) <notice>run boot scripts (boot.klog boot.ipconfig) Enabling syn flood protectiondone Disabling IP forwardingdone Creating /var/log/boot.msg done<notice>killproc: kill(230,29) <notice>exit status of (boot.klog boot.ipconfig) is (0 0) System Boot Control: The system has been set up Skipped features: boot.sched System Boot Control: Running /etc/init.d/boot.local done<notice>killproc: kill(230,3) INIT: Boot logging started on /dev/tty1(/dev/console) at Tue May 11 17:56:18 2004 Master Resource Control: previous runlevel: N, switching to runlevel: 5 <notice>Entering runlevel: 5 hotplug)start services (random isdnHotplug is already active (disable with NOHOTPLUG=1 at the boot prompt)done Initializing random number generatordone <notice> hotplug) is (0exit status of (random isdn 0 0) <notice>start services (coldplug) coldplug scanning input: done scanning pci: .*W**..******W****done scanning usb: .....done . . . . . . . . . . . . . . . . . . . . . . . .done <notice>exit status of (coldplug) is (0) <notice>start services (network) Setting up network interfaces: lo lo IP address: 127.0.0.1/8 done eth0 device: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30) eth0 configuration: eth-id-00:10:5a:d9:39:0e eth0 (DHCP) . <notice>pidofproc: dhcpcd 2923 IP/Netmask: 192.168.0.40 / 255.255.255.0 ('amd64') done eth1 device: Realtek Semiconductor Co., Ltd. RTL-8169 (rev 10) eth1 configuration: eth-id-00:0c:76:b4:b3:71 eth1 IP address: 192.168.0.89/24 doneSetting up service network . . . . . . . . . . . . . . . .done <notice>exit status of (network) is (0) <notice>start services (syslog) Starting syslog services<notice>startproc: execve (/sbin/syslogd) [ /sbin/syslogd -a /var/lib/ntp/dev/log ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=25 INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=147 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=55 SHLVL=2 BOOT_IMAGE=Linux splash=silent sscripts=43 _=/sbin/startproc DAEMON=/sbin/syslogd ] <notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -2 ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=25 INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=147 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=55 SHLVL=2 BOOT_IMAGE=Linux splash=silent sscripts=43 _=/sbin/startproc DAEMON=/sbin/klogd ] done <notice>exit status of (syslog) is (0) <notice>start services (smbfs) Mount SMB File System unused <notice>exit status of (smbfs) is (6) <notice>start services (splash_early resmgr portmap) <notice>startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=27 INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=147 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=55 SHLVL=2 BOOT_IMAGE=Linux splash=silent sscripts=43 _=/sbin/startproc DAEMON=/sbin/portmap ] <notice>startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=27 INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=147 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=55 SHLVL=2 BOOT_IMAGE=Linux splash=silent sscripts=43 _=/sbin/startproc DAEMON=/sbin/resmgrd ] Starting RPC portmap daemondone Starting resource managerdone <notice>exit status of (splash_early resmgr portmap) is (0 0 0) <notice>start services (nfsboot) Starting nfsboot (sm-notify) Backgrounding to notify hosts... done <notice>exit status of (nfsboot) is (0) <notice>start services (sshd powersaved fbset alsasound) <notice>startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=31 INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=147 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=55 SHLVL=2 BOOT_IMAGE=Linux splash=silent sscripts=43 _=/sbin/startproc DAEMON=/usr/sbin/sshd ] Starting SSH daemondone <notice>startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -e /etc/powersave.conf -a resmgr -v 3 ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=31 INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=147 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=55 SHLVL=2 BOOT_IMAGE=Linux splash=silent sscripts=43 _=/sbin/startproc DAEMON=/usr/sbin/powersaved ] loading ACPI modules (ac battery button fan processor thermal ) Starting powersaved done Starting sound driver: via82xxdone Restoring the previous sound settingdone <notice>exit status of (sshd powersaved fbset alsasound) is (0 0 0 0) <notice>start services (splash postfix kbd cups) <notice>startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=35 INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=147 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=55 SHLVL=2 BOOT_IMAGE=Linux splash=silent sscripts=43 _=/sbin/startproc DAEMON=/usr/sbin/cupsd ] Starting cupsddone Starting mail service (Postfix)done Loading keymap qwertz/de-latin1-nodeadkeys.map.gz doneLoading compose table latin1.adddone Start Unicode mode doneLoading console font lat9w-16.psfu -m trivial (K done<notice>exit status of (splash postfix kbd cups) is (0 0 0 0) <notice>start services (nscd hwscan cron) <notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=39 INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=147 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=55 SHLVL=2 BOOT_IMAGE=Linux splash=silent sscripts=43 _=/sbin/startproc DAEMON=/usr/sbin/cron ] Starting hardware scan on bootStarting CRON daemondone <notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=39 INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=147 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=55 SHLVL=2 BOOT_IMAGE=Linux splash=silent sscripts=43 _=/sbin/startproc DAEMON=/usr/sbin/nscd ] Starting Name Service Cache Daemondone <notice>exit status of (nscd hwscan cron) is (0 0 0) <notice>start services (xdm splash_late) Starting service kdm<notice>startproc: execve (/opt/kde3/bin/kdm) [ /opt/kde3/bin/kdm ], [ LC_MONETARY= CONSOLE=/dev/console TERM=linux SHELL=/bin/sh LC_NUMERIC= QTDIR=/usr/lib/qt3 LC_ALL= progress=42 INIT_VERSION=sysvinit-2.85 KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 AUTOBOOT=YES COLUMNS=147 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin LC_MESSAGES= RUNLEVEL=5 LC_COLLATE= PWD=/ LANG=de_DE.UTF-8 PREVLEVEL=N LINES=55 SHLVL=2 BOOT_IMAGE=Linux XCURSOR_THEME=crystalwhite no_proxy=localhost WINDOWMANAGER=/usr/X11R6/bin/kde LC_CTYPE=de_DE.UTF-8 splash=silent sscripts=43 LC_TIME= _=/sbin/startproc DAEMON=/opt/kde3/bin/kdm ] done <notice>exit status of (xdm splash_late) is (0 0) Master Resource Control: runlevel 5 has been reached Skipped services in runlevel 5: smbfs <notice>killproc: kill(957,3) amd64:~ # cat /proc/cmdline auto BOOT_IMAGE=Linux root=2103 splash=silent console=tty0 desktop resume=/dev/hde5 showopts
Thomas Köhler <sorcerer@counterstrike.de> writes:
<6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) <6>CPU: L2 Cache: 512K (64 bytes/line) <4>CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00
This confuses me - stepping 00 looks strange, Andreas -- Andreas Jaeger, aj@suse.de, http://www.suse.de/~aj SUSE Linux AG, Maxfeldstr. 5, 90409 Nürnberg, Germany GPG fingerprint = 93A3 365E CE47 B889 DF7F FED1 389A 563C C272 A126
On Wed, May 12, 2004 at 07:01:48AM +0200, Andreas Jaeger wrote:
Thomas K?hler <sorcerer@counterstrike.de> writes:
<6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) <6>CPU: L2 Cache: 512K (64 bytes/line) <4>CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00
This confuses me - stepping 00 looks strange,
Most likely he has a broken BIOS. The stepping is configured by the BIOS using the mask number iirc. -Andi
participants (4)
-
Andi Kleen -
Andreas Jaeger -
Jonathan Breeze -
Thomas Köhler