Can't start second processor on IWILL DK8S2

28 May 2004


      I've installed SuSE 9.1 Professional on an iWill DK8S2 with 512 MB.
    This is a fairly generic dual processor Opteron MB.  Kernel version
    is 2.6.4-52-smp no patches applied, straight from the Distribution.
    Runs fine as a single processor system; however, dual processor
    often won't complete boot (dies in the cold plug scan), or machine
    checks after some random (short) time:

    CPU0 machine check    4bank4: 0xb200002000010c0f
    RIP !INEXACT! 10:<ffffffff8034cfc0>  accel_putcs+0x220/0x340
    TSC 397101057

    Sorry about any inaccuracies in the above, had to transcribe it
    by hand, so some number of f's or 0's may be off.  However, this
    same board boots SuSE 8.0 Pro (2.4.19) on the same hardware.
    The bank interleave is disabled in the BIOS, but the node
    interleave is set to "auto".  When node interleave is disabled,
    the machine check isn't seen, but the machine quietly hangs.

    Included below is the cat of /proc/cpuinfo and an edited dmesg
    from the faulting combination, followed by the 2.4.19 version.
    Any help getting the second processor reliably on-line is greatly
    appreciated.

-bob
----
    cat /proc/cpuinfo 

processor	: 0
vendor_id	: AuthenticAMD
cpu family	: 15
model		: 5
model name	: AMD Opteron(tm) Processor 242
stepping	: 0
cpu MHz		: 1603.663
cache size	: 1024 KB
fpu		: yes
fpu_exception	: yes
cpuid level	: 1
wp		: yes
flags		: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext lm 3dnowext 3dnow
bogomips	: 3153.92
TLB size	: 1088 4K pages
clflush size	: 64
address sizes	: 40 bits physical, 48 bits virtual
power management: ts ttp

processor	: 1
vendor_id	: AuthenticAMD
cpu family	: 15
model		: 5
model name	: AMD Opteron(tm) Processor 242
stepping	: 0
cpu MHz		: 1603.663
cache size	: 1024 KB
fpu		: yes
fpu_exception	: yes
cpuid level	: 1
wp		: yes
flags		: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext lm 3dnowext 3dnow
bogomips	: 3203.07
TLB size	: 1088 4K pages
clflush size	: 64
address sizes	: 40 bits physical, 48 bits virtual
power management: ts ttp

    edited dmesg...

No AGP bridge found
Built 2 zonelists
Kernel command line: root=/dev/hda3 vga=0x31a splash=silent console=tty0 desktop resume=/dev/hda2 showopts 3 maxcpus=2
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 16 (order 4: 256 bytes)
CKRM Initialized
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 1603.663 MHz processor.
Console: colour dummy device 80x25
Memory: 508716k/524224k available (3505k kernel code, 0k reserved, 1274k data, 228k init)
Calibrating delay loop... 3153.92 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
There is already a security framework initialized, register_security failed.
Failure registering capabilities with the kernel
selinux_register_security:  Registering secondary module capability
Capability LSM initialized
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Looking for DSDT in initrd ...No customized DSDT found in initrd!
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
POSIX conformance testing by UNIFIX
Using local APIC NMI watchdog using perfctr0
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU0: AMD Opteron(tm) Processor 242 stepping 00
per-CPU timeslice cutoff: 1024.37 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 rip 6000 rsp 1001fd37f58
Initializing CPU#1
Calibrating delay loop... 3203.07 BogoMIPS
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
AMD Opteron(tm) Processor 242 stepping 00
Total of 2 processors activated (6356.99 BogoMIPS).
ENABLING IO-APIC IRQs
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23, 3-0, 3-1, 3-2, 3-3, 4-0, 4-1, 4-2, 4-3 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
Detected 12.528 MHz APIC timer.
checking TSC synchronization across 2 CPUs: passed.
time.c: Using PIT/TSC based timekeeping.
Brought up 2 CPUs
do_initcalls
init_elf32_binfmt
init_elf_binfmt
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
No customized DSDT found!
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
 ... the first call_usermodehelper: pci_bus
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1)
00:00:07[A] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17 Mode:1 Active:1)
00:00:07[B] -> 2-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb9 -> IRQ 18 Mode:1 Active:1)
00:00:07[C] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19 Mode:1 Active:1)
00:00:07[D] -> 2-19 -> IRQ 19
IOAPIC[1]: Set PCI routing entry (3-1 -> 0xc9 -> IRQ 25 Mode:1 Active:1)
00:02:01[A] -> 3-1 -> IRQ 25
IOAPIC[1]: Set PCI routing entry (3-2 -> 0xd1 -> IRQ 26 Mode:1 Active:1)
00:02:01[B] -> 3-2 -> IRQ 26
IOAPIC[1]: Set PCI routing entry (3-3 -> 0xd9 -> IRQ 27 Mode:1 Active:1)
00:02:01[C] -> 3-3 -> IRQ 27
IOAPIC[1]: Set PCI routing entry (3-0 -> 0xe1 -> IRQ 24 Mode:1 Active:1)
00:02:01[D] -> 3-0 -> IRQ 24
IOAPIC[2]: Set PCI routing entry (4-1 -> 0xe9 -> IRQ 29 Mode:1 Active:1)
00:01:01[A] -> 4-1 -> IRQ 29
IOAPIC[2]: Set PCI routing entry (4-2 -> 0x32 -> IRQ 30 Mode:1 Active:1)
00:01:01[B] -> 4-2 -> IRQ 30
IOAPIC[2]: Set PCI routing entry (4-3 -> 0x3a -> IRQ 31 Mode:1 Active:1)
00:01:01[C] -> 4-3 -> IRQ 31
IOAPIC[2]: Set PCI routing entry (4-0 -> 0x42 -> IRQ 28 Mode:1 Active:1)
00:01:01[D] -> 4-0 -> IRQ 28
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
number of IO-APIC #3 registers: 4.
number of IO-APIC #4 registers: 4.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
.......    : physical APIC id: 02
.... register #01: 00170011
.......     : max redirection entries: 0017
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 02000000
.......     : arbitration: 02
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
 00 000 00  1    0    0   0   0    0    0    00
 01 001 01  0    0    0   0   0    1    1    39
 02 001 01  0    0    0   0   0    1    1    31
 03 001 01  0    0    0   0   0    1    1    41
 04 001 01  0    0    0   0   0    1    1    49
 05 001 01  0    0    0   0   0    1    1    51
 06 001 01  0    0    0   0   0    1    1    59
 07 001 01  0    0    0   0   0    1    1    61
 08 001 01  0    0    0   0   0    1    1    69
 09 001 01  0    1    0   1   0    1    1    71
 0a 001 01  0    0    0   0   0    1    1    79
 0b 001 01  0    0    0   0   0    1    1    81
 0c 001 01  0    0    0   0   0    1    1    89
 0d 001 01  0    0    0   0   0    1    1    91
 0e 001 01  0    0    0   0   0    1    1    99
 0f 001 01  0    0    0   0   0    1    1    A1
 10 001 01  1    1    0   1   0    1    1    A9
 11 001 01  1    1    0   1   0    1    1    B1
 12 001 01  1    1    0   1   0    1    1    B9
 13 001 01  1    1    0   1   0    1    1    C1
 14 000 00  1    0    0   0   0    0    0    00
 15 000 00  1    0    0   0   0    0    0    00
 16 000 00  1    0    0   0   0    0    0    00
 17 000 00  1    0    0   0   0    0    0    00

IO APIC #3......
.... register #00: 03000000
.......    : physical APIC id: 03
.... register #01: 00030011
.......     : max redirection entries: 0003
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
 00 001 01  1    1    0   1   0    1    1    E1
 01 001 01  1    1    0   1   0    1    1    C9
 02 001 01  1    1    0   1   0    1    1    D1
 03 001 01  1    1    0   1   0    1    1    D9

IO APIC #4......
.... register #00: 04000000
.......    : physical APIC id: 04
.... register #01: 00030011
.......     : max redirection entries: 0003
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
 00 001 01  1    1    0   1   0    1    1    42
 01 001 01  1    1    0   1   0    1    1    E9
 02 001 01  1    1    0   1   0    1    1    32
 03 001 01  1    1    0   1   0    1    1    3A
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ24 -> 1:0
IRQ25 -> 1:1
IRQ26 -> 1:2
IRQ27 -> 1:3
IRQ28 -> 2:0
IRQ29 -> 2:1
IRQ30 -> 2:2
IRQ31 -> 2:3
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
PCI-DMA: Disabling IOMMU.
vesafb: framebuffer at 0xfd000000, mapped to 0xffffff0000009000, size 8128k
vesafb: mode is 1280x1024x16, linelength=2560, pages=2
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
Initial HugeTLB pages allocated: 0
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
ikconfig 0.7 with /proc/config*
	...


    2.4.19 cpuinfo
processor	: 0
vendor_id	: AuthenticAMD
cpu family	: 15
model		: 5
model name	: AMD Opteron(tm) Processor 242
stepping	: 0
cpu MHz		: 1603.656
cache size	: 1024 KB
fpu		: yes
fpu_exception	: yes
cpuid level	: 1
wp		: yes
flags		: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext lm 3dnowext 3dnow
bogomips	: 3153.92
TLB size	: 1088 4K pages
clflush size	: 64
cache_alignment	: 64
address sizes	: 40 bits physical, 48 bits virtual
power management: ts ttp

processor	: 1
vendor_id	: AuthenticAMD
cpu family	: 15
model		: 5
model name	: AMD Opteron(tm) Processor 242
stepping	: 0
cpu MHz		: 1603.656
cache size	: 1024 KB
fpu		: yes
fpu_exception	: yes
cpuid level	: 1
wp		: yes
flags		: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext lm 3dnowext 3dnow
bogomips	: 3203.07
TLB size	: 1088 4K pages
clflush size	: 64
cache_alignment	: 64
address sizes	: 40 bits physical, 48 bits virtual
power management: ts ttp


    2.4.19 dmesg

id 2
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfebfe000] global_irq_base[0x18])
IOAPIC[1]: Assigned apic_id 3
IOAPIC[1]: apic_id 3, version 17, address 0xfebfe000, GSI 24-27
ACPI: IOAPIC (id[0x04] address[0xfebff000] global_irq_base[0x1c])
IOAPIC[2]: Assigned apic_id 4
IOAPIC[2]: apic_id 4, version 17, address 0xfebff000, GSI 28-31
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Using ACPI (MADT) for SMP configuration information
Checking aperture...
CPU 0: aperture @ eef2000000 size 32 MB
Aperture from northbridge cpu 0 too small (32 MB)
No AGP bridge found
Built 2 zonelists
Kernel command line: root=/dev/hda5 vga=791 console=tty0
Initializing CPU#0
PID hash table entries: 16 (order 4: 256 bytes)
CKRM Initialization
CKRM Initialization done
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 1603.656 MHz processor.
Console: colour dummy device 80x25
Memory: 509192k/524224k available (3620k kernel code, 0k reserved, 1282k data, 216k init)
Calibrating delay loop... 3153.92 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
There is already a security framework initialized, register_security failed.
Failure registering capabilities with the kernel
selinux_register_security:  Registering secondary module capability
Capability LSM initialized
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
POSIX conformance testing by UNIFIX
Using local APIC NMI watchdog using perfctr0
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU0: AMD Opteron(tm) Processor 242 stepping 00
per-CPU timeslice cutoff: 1024.37 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 rip 6000 rsp 1001ff0bf58
Initializing CPU#1
Calibrating delay loop... 3203.07 BogoMIPS
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
AMD Opteron(tm) Processor 242 stepping 00
Total of 2 processors activated (6356.99 BogoMIPS).
ENABLING IO-APIC IRQs
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23, 3-0, 3-1, 3-2, 3-3, 4-0, 4-1, 4-2, 4-3 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
Detected 12.528 MHz APIC timer.
checking TSC synchronization across 2 CPUs: passed.
time.c: Using PIT/TSC based timekeeping.
Brought up 2 CPUs
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
No customized DSDT found!
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1)
00:00:07[A] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17 Mode:1 Active:1)
00:00:07[B] -> 2-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb9 -> IRQ 18 Mode:1 Active:1)
00:00:07[C] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19 Mode:1 Active:1)
00:00:07[D] -> 2-19 -> IRQ 19
IOAPIC[1]: Set PCI routing entry (3-1 -> 0xc9 -> IRQ 25 Mode:1 Active:1)
00:02:01[A] -> 3-1 -> IRQ 25
IOAPIC[1]: Set PCI routing entry (3-2 -> 0xd1 -> IRQ 26 Mode:1 Active:1)
00:02:01[B] -> 3-2 -> IRQ 26
IOAPIC[1]: Set PCI routing entry (3-3 -> 0xd9 -> IRQ 27 Mode:1 Active:1)
00:02:01[C] -> 3-3 -> IRQ 27
IOAPIC[1]: Set PCI routing entry (3-0 -> 0xe1 -> IRQ 24 Mode:1 Active:1)
00:02:01[D] -> 3-0 -> IRQ 24
IOAPIC[2]: Set PCI routing entry (4-1 -> 0xe9 -> IRQ 29 Mode:1 Active:1)
00:01:01[A] -> 4-1 -> IRQ 29
IOAPIC[2]: Set PCI routing entry (4-2 -> 0x32 -> IRQ 30 Mode:1 Active:1)
00:01:01[B] -> 4-2 -> IRQ 30
IOAPIC[2]: Set PCI routing entry (4-3 -> 0x3a -> IRQ 31 Mode:1 Active:1)
00:01:01[C] -> 4-3 -> IRQ 31
IOAPIC[2]: Set PCI routing entry (4-0 -> 0x42 -> IRQ 28 Mode:1 Active:1)
00:01:01[D] -> 4-0 -> IRQ 28
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
number of IO-APIC #3 registers: 4.
number of IO-APIC #4 registers: 4.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
.......    : physical APIC id: 02
.... register #01: 00170011
.......     : max redirection entries: 0017
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 02000000
.......     : arbitration: 02
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
 00 000 00  1    0    0   0   0    0    0    00
 01 001 01  0    0    0   0   0    1    1    39
 02 001 01  0    0    0   0   0    1    1    31
 03 001 01  0    0    0   0   0    1    1    41
 04 001 01  0    0    0   0   0    1    1    49
 05 001 01  0    0    0   0   0    1    1    51
 06 001 01  0    0    0   0   0    1    1    59
 07 001 01  0    0    0   0   0    1    1    61
 08 001 01  0    0    0   0   0    1    1    69
 09 001 01  0    1    0   1   0    1    1    71
 0a 001 01  0    0    0   0   0    1    1    79
 0b 001 01  0    0    0   0   0    1    1    81
 0c 001 01  0    0    0   0   0    1    1    89
 0d 001 01  0    0    0   0   0    1    1    91
 0e 001 01  0    0    0   0   0    1    1    99
 0f 001 01  0    0    0   0   0    1    1    A1
 10 001 01  1    1    0   1   0    1    1    A9
 11 001 01  1    1    0   1   0    1    1    B1
 12 001 01  1    1    0   1   0    1    1    B9
 13 001 01  1    1    0   1   0    1    1    C1
 14 000 00  1    0    0   0   0    0    0    00
 15 000 00  1    0    0   0   0    0    0    00
 16 000 00  1    0    0   0   0    0    0    00
 17 000 00  1    0    0   0   0    0    0    00

IO APIC #3......
.... register #00: 03000000
.......    : physical APIC id: 03
.... register #01: 00030011
.......     : max redirection entries: 0003
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
 00 001 01  1    1    0   1   0    1    1    E1
 01 001 01  1    1    0   1   0    1    1    C9
 02 001 01  1    1    0   1   0    1    1    D1
 03 001 01  1    1    0   1   0    1    1    D9

IO APIC #4......
.... register #00: 04000000
.......    : physical APIC id: 04
.... register #01: 00030011
.......     : max redirection entries: 0003
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
 00 001 01  1    1    0   1   0    1    1    42
 01 001 01  1    1    0   1   0    1    1    E9
 02 001 01  1    1    0   1   0    1    1    32
 03 001 01  1    1    0   1   0    1    1    3A
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ24 -> 1:0
IRQ25 -> 1:1
IRQ26 -> 1:2
IRQ27 -> 1:3
IRQ28 -> 2:0
IRQ29 -> 2:1
IRQ30 -> 2:2
IRQ31 -> 2:3
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
PCI-DMA: Disabling IOMMU.
vesafb: framebuffer at 0xfd000000, mapped to 0xffffff0000009000, size 8128k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
Initial HugeTLB pages allocated: 0
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
CPU0:  online
 domain 0: span 03
  groups: 01 02
CPU1:  online
 domain 0: span 03
  groups: 02 01
ikconfig 0.7 with /proc/config*
VFS: Disk quotas dquot_6.5.1
klog channel created (2097152 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.6 [Flags: R/O].
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU1] (supports C1, 8 throttling states)
ACPI: Processor [CPU2] (supports C1)
Console: switching to colour frame buffer device 128x48
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
hw_random: AMD768 system management I/O registers at 0x5000.
hw_random hardware driver 1.0.0 loaded
ppdev: user-space parallel port driver

--

bob＠Baruch.pantasys

tags

participants (1)