Hi Volker, Thanks for the info - yeah I can't believe how hot the chipset runs! Following your instructions I initialised sensors (with the default conf file), rebooted (went to make a coffee) and came back to a machine that sounded like a wailing banshee :) Guess those configuration values are wrong ;) I don't have access to a decent avo, but I'll have a dig around and see if I can find any more information on the mobo. Merry Christmas, Jon. Volker Kuhlmann wrote:
I've never bothered with sensor, but I guess I should :) I had a quick look and my sensors.conf (which is just the default one) - obviously I have no experience altering this file, but would be more than willing to help out wherever possible. If you can supply me with a list of checks to run, I'll report back........?
I thought knowing the temperatures would be handy, and anyway, it's a useful diagnostic and it's supposed to work. To configure it, run sensors-detect. It worked with just pressing enter on all questions. You said before you had a GA-K8NF9-Ultra, according to the manual, the differences are nforce4-ultra chipset instead of nforce4-4X, and a third fan header next to the big power connector. /etc/init.d/lm_sensors restart, and things are off the ground. Kudos to the sensors team and SUSE.
Now the tricky bit is working out to which chip inputs Gigabyte has connected the various fan, thermistor and voltage lines. For the latter two, it's also important to know the value of various resistors used. For the truely dedicated, it's time for a meter and PCB track tracing... Otherwise, guess values which were recommended in the chip's (ITE IT7812?) reference application note...
The default values from sensors are useless. Also, I had trouble getting it to load the correct lines belonging to the chip section in /etc/sensors.conf, so it's best to clear out the file (keep some comments) and only put the necessary lines into it. So far, I have
# Modified from: # http://forums.gentoo.org/viewtopic-t-307015-highlight-sensors+nforce3.html
chip "it8712-*"
label in0 "VCore1" label in1 "VCore2" label in2 "+3.3V" label in3 "+5V" label in4 "+12V" label in5 "-12V" label in6 "-5V" label in7 "Stdby" label in8 "VBat"
ignore vid ignore in3 ignore in5 ignore in6 ignore in7 ignore in8
compute in0 0.03+@ , @-0.03 compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1) compute in4 ((30/10) +0.97)*@ , @/((30/10) +0.97) compute in5 (7.67 * @) - 27.36 , (@ + 27.36) / 7.67 compute in6 (4.33 * @) - 13.64 , (@ + 13.64) / 4.33 compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
set in0_min 1.2 set in0_max 1.8 set in1_min 2.4 set in1_max 2.9 set in2_min 3.3 * 0.95 set in2_max 3.3 * 1.05 set in3_min 5.0 * 0.95 set in3_max 5.0 * 1.05 set in4_min 12 * 0.95 set in4_max 12 * 1.05 set in5_max -12 * 0.95 set in5_min -12 * 1.05 set in6_max -5 * 0.95 set in6_min -5 * 1.05 set in7_min 5 * 0.95 set in7_max 5 * 1.05
label temp1 "M/B Temp" set temp1_over 40 set temp1_low 10 label temp2 "CPU Temp" set temp2_over 45 set temp2_low 10 ignore temp3
# Fans set fan1_min 1000 set fan2_min 0 ignore fan3
That's work in progress. You'll want to edit the fan3 settings. (Wonder whether it's possible to solder the missing fan header on the K8NF-9...) The BIOS display of CPU temp is 2°C lower for me, at around 30°C. As the BIOS doesn't display actual voltages, one would have to compare with a voltmeter. I don't know what Vcore1 is, but it looks dubious:
VCore1: +1.42 V (min = +1.20 V, max = +1.81 V)
The BIOS summarises Vcore1 + 2 under Vcore, so one doesn't even know what numbers one is supposed to get from sensors.
All in all, these mobos don't have a very extensive monitoring capability. If I find out more, I'll post it.
Btw the chipset heatsink runs at about 70°C - is that normal/desirable/fixable?
HTH + Thanks,
Volker
-- Jonathan Brooks (Ph.D.) - Research Fellow PaIN Group, Department of Human Anatomy & Genetics, University of Oxford, South Parks Road, Oxford, OX1 3QX tel: +44(0)1865-282654 fax: +44(0)1865-282656 web: http://www.fmrib.ox.ac.uk/~jon