From the Beast I can enter Seth1's quad into the URL and display Sony's localhost webpage. But, I cannot display the Beast's localhost webpage from Sony. Neither can I access the internet from the Beast through the Sony, either by quad address or domain name. When I attempt to display
I have installed an EN104 hub and connected Sony's eth1 and the Beast's eth0 to it. The ADSL remains connected to Seth0. I do not want to connect the ADSL to the hub. I ran YaST2 and setup the network on both boxes. Well, apparenly YaST2 doesn't do it all. I can ping the Beast from the Sony and I can ping the Sony from the beast. the Beast's localhost web page I can see the hublight for the Sony blink, but not the Beasts. Obviously, YaST doesn't know how to install a LAN without some human help, and I don't have enough networking knowledge to be useful. What am I missing folks? Here are the stats: Sony's stats: root@JLKreps:/home/jerry > ifconfig eth0 Link encap:Ethernet HWaddr 00:50:04:77:B8:2F inet addr:192.168.200.2 Bcast:192.168.200.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10226 errors:0 dropped:0 overruns:0 frame:0 TX packets:9598 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:11 Base address:0xf400 eth1 Link encap:Ethernet HWaddr 00:01:02:CF:04:47 inet addr:192.168.201.2 Bcast:192.168.201.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:520 errors:0 dropped:0 overruns:0 frame:0 TX packets:381 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:11 Base address:0xf480 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:3924 Metric:1 RX packets:794 errors:0 dropped:0 overruns:0 frame:0 TX packets:794 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 root@JLKreps:/home/jerry > netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.201.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.200.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.200.1 0.0.0.0 UG 0 0 0 eth0 (192.168.200.1 is the gateway to the ADSL and 192.168.200.2 is the IP of the Seth0 that the ADSL is connected to.) The Beast's stats: root@JLKreps:/home/jerry > ifconfig eth0 Link encap:Ethernet HWaddr 00:01:02:CF:03:92 inet addr:192.168.200.3 Bcast:192.168.201.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:111 errors:0 dropped:0 overruns:0 frame:0 TX packets:93 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:11 Base address:0xec00 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:3924 Metric:1 RX packets:36 errors:0 dropped:0 overruns:0 frame:0 TX packets:36 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 root@JLKreps:/home/jerry > netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.201.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.201.2 0.0.0.0 UG 0 0 0 eth0 Sony's /etc/hosts file: root@JLKreps:/home/jerry > cat /etc/hosts # # hosts This file describes a number of hostname-to-address # mappings for the TCP/IP subsystem. It is mostly # used at boot time, when no name servers are running. # On small systems, this file can be used instead of a # "named" name server. # Syntax: # # IP-Address Full-Qualified-Hostname Short-Hostname # 127.0.0.1 localhost # special IPv6 addresses ::1 localhost ipv6-localhost ipv6-loopback fe00::0 ipv6-localnet ff00::0 ipv6-mcastprefix ff02::1 ipv6-allnodes ff02::2 ipv6-allrouters ff02::3 ipv6-allhosts 192.168.201.2 JLKreps.AtHome JLKreps root@JLKreps:/home/jerry > Sony's /etc/networks file: root@JLKreps:/home/jerry > cat /etc/networks # # networks This file describes a number of netname-to-address # mappings for the TCP/IP subsystem. It is mostly # used at boot time, when no name servers are running. # loopback 127.0.0.0 JerryKreps 192.168.201.3 # End. root@JLKreps:/home/jerry > The Beast's /etc/hosts file has these two lines: 127.0.0.0 loopback 192.168.201.2 JLKreps The Beast's /etc/networks file has: loopback 127.0.0.0 JLKreps 192.168.201.2 That's it. What's my problem? (Computer-wise, not mentally! ;-) JLK