[SLE] freesco setup and config
Hi evey one , downloaded freesco and cant seem to get it working. I want to use it with the following ethernet card access the internal network and modem it access the external network/ISP/internet. So how do you set up masqerading ? and how do you set up ppp and how does it handle the ever changing ISP assined ip address an each redial ? then how do you test that its working ? hardware P100 w two 1/2 gig drives , freesco on bootable floppy (once it works Ill think about moving it to the hd. nevell ne1000/2000 compatable card using io=0x300 and irq 11 external modem on com port one. freesco see them both. -- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq
Further to my delema , on restart I het an error that Enable port fowarding ........DELAYED I am also somewhat confused about setting up the dhcp server and client , isp address - Its server assinged so why is it asking for it in the config set up ? and port fowarding/masqerading , I set it up I think when I put in the range 10.20.30.0 10.20.30.10 , card is set up to 10.20.30.9 w 255.0.0.0 thanks Samy At 04:43 PM 7/3/2000 +0000, Samy Elashmawy wrote:
Hi evey one , downloaded freesco and cant seem to get it working. I want to use it with the following
ethernet card access the internal network and modem it access the external network/ISP/internet.
So how do you set up masqerading ? and how do you set up ppp and how does it handle the ever changing ISP assined ip address an each redial ? then how do you test that its working ?
hardware P100 w two 1/2 gig drives , freesco on bootable floppy (once it works Ill think about moving it to the hd. nevell ne1000/2000 compatable card using io=0x300 and irq 11 external modem on com port one.
freesco see them both.
-- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com
Also check the FAQ at http://www.suse.com/support/faq
-- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq
On Mon, Jul 03, 2000 at 05:35:00PM +0000, Samy Elashmawy wrote:
Further to my delema , on restart I het an error that
Enable port fowarding ........DELAYED
Don't worry about it. (I know I did, at first ;) ) Unless you intend to make an internal webserver or something accessable to the outside, you don't need any port forwarding.
I am also somewhat confused about setting up the dhcp server and client , isp address - Its server assinged so why is it asking for it in the config set up ? and port fowarding/masqerading , I set it up I think when I put in the range 10.20.30.0 10.20.30.10 , card is set up to 10.20.30.9 w 255.0.0.0
Ok, I'm thinking one (or both, entirely possible) of us is confused here. There is a point where freesco asks you if you want to use dhcp to set up the first interface, i.e. eth0. I think this mainly pertains to people w/ cablemodems, dsl, etc. In these cases I think they get their ip address and other network information via dhcp from their isp. I doubt your isp does this if you have a dialup link, but I could be wrong here (not the first time). The DHCP range applies to what range you want your client machines to receive addresses from, not to your freesco box. FWIW, make sure your 'range' excludes the ip of your internal interface i.e. eth0 on your lan. Otherwise, since dhcp didn't assign it to that interface itself, it is 'free' to assign it to the next machine that asks for it, and then you have more than one machine that thinks it is at that ip address. Not good. To be blunt, forget about masqerading. It is already done for you at this point. Don't worry about it. Monte
thanks
Samy At 04:43 PM 7/3/2000 +0000, Samy Elashmawy wrote:
Hi evey one , downloaded freesco and cant seem to get it working. I want to use it with the following
ethernet card access the internal network and modem it access the external network/ISP/internet.
So how do you set up masqerading ? and how do you set up ppp and how does it handle the ever changing ISP assined ip address an each redial ? then how do you test that its working ?
hardware P100 w two 1/2 gig drives , freesco on bootable floppy (once it works Ill think about moving it to the hd. nevell ne1000/2000 compatable card using io=0x300 and irq 11 external modem on com port one.
freesco see them both.
-- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com
Also check the FAQ at http://www.suse.com/support/faq
-- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq
__________________________________________________ Do You Yahoo!? Talk to your friends online with Yahoo! Messenger. http://im.yahoo.com -- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq
On Mon, Jul 03, 2000 at 04:43:41PM +0000, Samy Elashmawy wrote:
Hi evey one , downloaded freesco and cant seem to get it working. I want to use it with the following
ethernet card access the internal network and modem it access the external network/ISP/internet.
So how do you set up masqerading ? and how do you set up ppp and how does it handle the ever changing ISP assined ip address an each redial ? then how do you test that its working ?
Well, Sam, I hate to point out the obvious, but try the Forums listed on the Freesco page, and the Knowledge page link that is there also. Everything you need has been hashed over many times before in that forum, where you have more or less direct access to the developer and several maintainers, not to mention more than a few people sold on Freesco ;). That said, assuming you are starting from a freshly created Freesco floppy disk: 1) put the disk in the drive 2) turn on the 'puter 3) when the boot logo for Freesco comes up, follow the directions type 'setup' and hit enter. 4) It should prompt you to login as root and enter the root passwd (default is 'root'), Do this, then hit enter again. 5) Select what configuration you want. In this case, it sounds like you probably want what I am using, which is d)ialup, where Freesco acts as firewall/gateway btwn your lan and the rest of the world. 6) Answer the questions as you go. In most cases, the default is reasonable. I presume you already know what you are using/want to use for ip address, netmask, hostname, and domain name for this box Make sure you enable the web control panel on port 82! 7) One thing to beware of: Make very sure that the options for things like telnet server, web server, dhcp, etc that have options like (y/s/n) that you either pick (s)ecure(internal interface only) or (n)o for not at all. Otherwise, you will be making that service available to the Internet via your dialup link. Not generally a good idea! 8) Skip thinks like port forwarding, DHCP, print server, time server, etc. for now. You can fiddle with them later. 9) You can select what you want for dial-on-demand settings, by either choosing (0) for filter.cfg (see diald docs for info), or entering number of seconds you want an idle link to stay up. *Note* this is my only gripe w/ 0.26 right now... Using (0) it doesn't seem to autodial for me. Probably a minor tweak, or just have to use a default timeout like 600 seconds. YMMV. 10) Enter the info for your isp (connection name, user name, password, pap/chap/script, and you should be about done. When finished, reboot. Let it get completely done. If you are really worried about it, log in from the console as root (remember the passwd?) and type 'ifconfig'. This will give you the status of all the network interfaces. Try pinging your internal hosts, using IP addresses. This should work w/o any fiddling. Then type 'control up' as root. You should hear your modem come on, and dial. After a little bit, try ifconfig again to see if ppp0 is up. That should be about it! Change your root passwd immediately! 11) Now use a web browser on your internal net (use Netscape or IE. kfm and lynx won't cut it) Point it at the address of the gateway box like this 'http://10.0.0.1:82' for a gateway host at ip address 10.0.0.1. You should see a black screen w/ a login link in the center. Click it, and login as admin, w/ passwd 'admin'. 12) You can now control your Freesco box from this panel. If you are like me and have kids/significant other who are not tech's, you can add a non-admin web-user w/ no passwd, which can just bring the link up and down, or block it (incase of important incoming phone calls, etc.) 13) Now for the hard(er) part. Using telnet, or a console attached to the gateway, log in as root, cd to /mnt/router/etc/. This is Where all the config files are saved on the floppy. The other ones under /etc/ itself are in the ramdisk. Any changes to /etc will be lost on reboot. So make your changes here. The default editor is invoked like so: 'edit named.hst' which is where you want to put entries for your local hosts on your lan, so as to avoid spurious dial-outs. Also edit the appropriate namedxxx.rev file, which is the reverse mapping file. The examples are pretty good; just add similar ones for your lan. And reboot. You should be set now. For further goodies, look on the web pages I mentioned above. Enjoy, Monte
hardware P100 w two 1/2 gig drives , freesco on bootable floppy (once it works Ill think about moving it to the hd. nevell ne1000/2000 compatable card using io=0x300 and irq 11 external modem on com port one.
freesco see them both.
-- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq
__________________________________________________ Do You Yahoo!? Talk to your friends online with Yahoo! Messenger. http://im.yahoo.com -- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/support/faq
participants (3)
-
milanuk＠yahoo.com -
monte＠yahoo.com -
samelash＠ix.netcom.com