New subject: [opensuse] Require help & guidance on displaying for presentation

27 Feb 2008

      Dual head support is "variable" depending on your card and driver.   
Attached is my xorg.conf.  however you configure your system note the
"dual..." settings like those below.

good luck..
wcn

Section "Device"
  BoardName    "RV350 NP"
  BusID        "1:0:0"
  Driver       "radeon"
  Identifier   "Device[0]"
  Option       "SaXDualHead"
  Option       "IgnoreEDID"
  Option       "MergedFB"
  Option       "GARTSize" "32"
  Option       "SaXDualMonitorVendor" "SAMSUNG"
  Option       "SaXDualVSync" "56-75"
  Option       "CRT2Position" "Clone"
  Option       "MonitorLayout" "AUTOCRT,CRT"
  Option       "CRT2VRefresh" "56-75"
  Option       "MetaModes"
"1400x1050,1280x1024;1280x1024,1280x1024;1024x768,1024x768;800x600,800x600"
  Option       "SaXDualOrientation" "LeftOf"
  Option       "SaXDualResolution" "1280x1024"
  Option       "CRT2HSync" "30-81"
  Option       "SaXDualMode" "Clone"
  Option       "SaXDualHSync" "30-81"
  Option       "SaXDualMonitorModel" "SYNCMASTER 910T"
  Option       "XaaNoOffscreenPixmaps"
  VendorName   "ATI"
EndSection

ChongMing@e7tech.com wrote:
...
Thanks for the information. I went to yast, hardware, Graphics card and monitor.
Inside i see a dual head mode settings. What is it use for? is it use to set up
the external monitor settings?
regards chongming
Quoting Wendell Nichols :
...
Check out xrandr.  I use it to select the resolution of the monitor I'm
currentlh "looking" at.   Of course it only allows you to choose between
resolutions actually configured in you server's config (which was likely
done via SAX).  Your monitor could be blank because your video output is
out of range.  Selecting an "in range" resolution might help.
I find linux very weak in the area of external monitor(s).  There are
lots of times I look stupid because I can't make my linux laptop work
with some old projector and I have to resort to using someone's old
windows box.
sigh..
wcn
jdd wrote:
...
Chong Ming a écrit :
...
Hi guys, i using SUse 10.3 for 32 bit . I need to connect to a large
monitor or projector to display my screen for presentation.
My situation is this.
I connect my laptop to a samsung lcd monitor. on the loading page, it
is able to display on the samsung lcd. But once my machine loads the
desktop, the lcd monitor display blacks out and the client dislay is
never on the lcd display again.
Once i boot off, it comes up the boot off screen, the lcd display the
details on my laptop display again.
What is the problem behind it? How to set up?
Required guidance on this urgent matter.
regards
chongming
there is probably a key on your keyboard to switch between the two
screens, but this one don't works always.
you can also try sax2 (or yast, display), there are option to
configure two displays at the same time
jdd
-- 
To unsubscribe, e-mail: opensuse+unsubscribe@opensuse.org
For additional commands, e-mail: opensuse+help@opensuse.org
# /.../
# SaX generated X11 config file
# Created on: 2007-10-22T13:49:57-0600.
#
# Version: 8.1
# Contact: Marcus Schaefer , 2005
# Contact: SaX-User list https://lists.berlios.de/mailman/listinfo/sax-users
#
# Automatically generated by [ISaX] (8.1)
# PLEASE DO NOT EDIT THIS FILE!
#

Section "Files"
  FontPath     "/usr/share/fonts/misc:unscaled"
  FontPath     "/usr/share/fonts/local"
  FontPath     "/usr/share/fonts/75dpi:unscaled"
  FontPath     "/usr/share/fonts/100dpi:unscaled"
  FontPath     "/usr/share/fonts/Type1"
  FontPath     "/usr/share/fonts/URW"
  FontPath     "/usr/share/fonts/Speedo"
  FontPath     "/usr/share/fonts/PEX"
  FontPath     "/usr/share/fonts/cyrillic"
  FontPath     "/usr/share/fonts/latin2/misc:unscaled"
  FontPath     "/usr/share/fonts/latin2/75dpi:unscaled"
  FontPath     "/usr/share/fonts/latin2/100dpi:unscaled"
  FontPath     "/usr/share/fonts/latin2/Type1"
  FontPath     "/usr/share/fonts/latin7/75dpi:unscaled"
  FontPath     "/usr/share/fonts/baekmuk:unscaled"
  FontPath     "/usr/share/fonts/japanese:unscaled"
  FontPath     "/usr/share/fonts/kwintv"
  FontPath     "/usr/share/fonts/truetype"
  FontPath     "/usr/share/fonts/uni:unscaled"
  FontPath     "/usr/share/fonts/CID"
  FontPath     "/usr/share/fonts/ucs/misc:unscaled"
  FontPath     "/usr/share/fonts/ucs/75dpi:unscaled"
  FontPath     "/usr/share/fonts/ucs/100dpi:unscaled"
  FontPath     "/usr/share/fonts/hellas/misc:unscaled"
  FontPath     "/usr/share/fonts/hellas/75dpi:unscaled"
  FontPath     "/usr/share/fonts/hellas/100dpi:unscaled"
  FontPath     "/usr/share/fonts/hellas/Type1"
  FontPath     "/usr/share/fonts/misc/sgi:unscaled"
  FontPath     "/usr/share/fonts/xtest"
  FontPath     "/opt/kde3/share/fonts"
  InputDevices "/dev/gpmdata"
  InputDevices "/dev/input/mice"
EndSection

Section "ServerFlags"
  Option       "AllowMouseOpenFail" "on"
EndSection

Section "Module"
  Load         "dbe"
  Load         "type1"
  Load         "freetype"
  Load         "extmod"
  Load         "glx"
EndSection

Section "InputDevice"
  Driver       "kbd"
  Identifier   "Keyboard[0]"
  Option       "Protocol" "Standard"
  Option       "XkbLayout" "us"
  Option       "XkbModel" "microsoftpro"
  Option       "XkbRules" "xfree86"
EndSection

Section "InputDevice"
  Driver       "mouse"
  Identifier   "Mouse[1]"
  Option       "Buttons" "7"
  Option       "Device" "/dev/input/mice"
  Option       "Name" "Chesen Electronics PS/2 Keyboard+Mouse Adapter"
  Option       "Protocol" "explorerps/2"
  Option       "Vendor" "Sysp"
  Option       "ZAxisMapping" "4 5"
EndSection

Section "InputDevice"
  Driver       "synaptics"
  Identifier   "Mouse[3]"
  Option       "Buttons" "5"
  Option       "Device" "/dev/input/mice"
  Option       "Emulate3Buttons" "on"
  Option       "InputFashion" "Mouse"
  Option       "Name" "Synaptics;Touchpad"
  Option       "Protocol" "explorerps/2"
  Option       "SHMConfig" "on"
  Option       "Vendor" "Sysp"
  Option       "ZAxisMapping" "4 5"
EndSection

Section "Monitor"
  Identifier   "Monitor[0]"
  ModelName    "LGPHILIPSLCD LCD MONITOR"
  Option       "DPMS"
  VendorName   "LGP"
#  UseModes     "Modes[0]"
EndSection

Section "Modes"
  Identifier   "Modes[0]"
  Modeline 	"1400x1050" 122.61 1400 1488 1640 1880 1050 1051 1054 1087
  Modeline 	"1400x1050" 99.25 1400 1448 1480 1560 1050 1053 1057 1080 +HSync -Vsync
  Modeline 	"1024x768" 64.11 1024 1080 1184 1344 768 769 772 795
  Modeline 	"1024x768" 55.00 1024 1072 1104 1184 768 771 775 790 +HSync -Vsync
  Modeline 	"800x600" 38.22 800 832 912 1024 600 601 604 622
  Modeline 	"800x600" 34.75 800 848 880 960 600 603 607 617 +HSync -Vsync
  Modeline 	"1280x1024" 141.82 1280 1376 1512 1744 1024 1025 1028 1070
  Modeline 	"1280x960" 133.46 1280 1368 1504 1728 960 961 964 1003
  Modeline 	"1280x800" 110.20 1280 1360 1496 1712 800 801 804 836
  Modeline 	"1152x864" 107.91 1152 1224 1352 1552 864 865 868 903
  Modeline 	"1280x768" 105.85 1280 1360 1496 1712 768 769 772 803
  Modeline 	"1024x768" 85.08 1024 1088 1200 1376 768 769 772 803
  Modeline 	"1280x600" 81.24 1280 1344 1480 1680 600 601 604 628
  Modeline 	"1024x600" 64.99 1024 1080 1184 1344 600 601 604 628
  Modeline 	"800x600" 51.06 800 840 928 1056 600 601 604 628
  Modeline 	"768x576" 46.80 768 808 888 1008 576 577 580 603
  Modeline 	"640x480" 31.54 640 664 728 816 480 481 484 502
EndSection

Section "Screen"
  DefaultDepth 24
  SubSection "Display"
    Depth      15
    Modes      "1400x1050" "1280x1024" "1024x768"
  EndSubSection
  SubSection "Display"
    Depth      16
    Modes      "1400x1050" "1280x1024" "1024x768"
  EndSubSection
  SubSection "Display"
    Depth      24
    Modes      "1400x1050" "1280x1024" "1024x768"
  EndSubSection
  SubSection "Display"
    Depth      8
    Modes      "1400x1050" "1280x1024" "1024x768"
  EndSubSection
  Device       "Device[0]"
  Identifier   "Screen[0]"
  Monitor      "Monitor[0]"
EndSection

Section "Device"
  BoardName    "RV350 NP"
  BusID        "1:0:0"
  Driver       "radeon"
  Identifier   "Device[0]"
  Option       "SaXDualHead"
  Option       "IgnoreEDID"
  Option       "MergedFB"
  Option       "GARTSize" "32"
  Option       "SaXDualMonitorVendor" "SAMSUNG"
  Option       "SaXDualVSync" "56-75"
  Option       "CRT2Position" "Clone"
  Option       "MonitorLayout" "AUTOCRT,CRT"
  Option       "CRT2VRefresh" "56-75"
  Option       "MetaModes" "1400x1050,1280x1024;1280x1024,1280x1024;1024x768,1024x768;800x600,800x600"
  Option       "SaXDualOrientation" "LeftOf"
  Option       "SaXDualResolution" "1280x1024"
  Option       "CRT2HSync" "30-81"
  Option       "SaXDualMode" "Clone"
  Option       "SaXDualHSync" "30-81"
  Option       "SaXDualMonitorModel" "SYNCMASTER 910T"
  Option       "XaaNoOffscreenPixmaps"  
  VendorName   "ATI"
EndSection

Section "ServerLayout"
  Identifier   "Layout[all]"
  InputDevice  "Keyboard[0]" "CoreKeyboard"
  InputDevice  "Mouse[1]" "CorePointer"
  InputDevice  "Mouse[3]" "SendCoreEvents"
  Option       "Clone" "off"
  Option       "Xinerama" "off"
  Screen       "Screen[0]"
EndSection

Section "DRI"
    Group      "video"
    Mode       0660
EndSection

Section "Extensions"
EndSection

Re: [opensuse] Require help & guidance on displaying for presentation

Wendell Nichols

Chong Ming

Patrick Shanahan

peter nikolic

Rajko M.

Chong Ming

peter nikolic

Banning someone out of personal spite is uncalled for fascism

Anders Johansson

Chong Ming

Rajko M.

jdd

Banning someone out of personal spite is uncalled for fascism

peter nikolic

JB2

tags

participants (9)