October 2012 - openSUSE Users - openSUSE Mailing Lists

[opensuse] can't set nfs4 acl's
by lynn 04 Oct '12

04 Oct '12

12.2 Hi When I try to set a nfs4 ACL on a nfs4 mounted file, I always get an error even though the ACE I'm setting is legal e.g. compartida is a folder which is nfs4 mounted: nfs4_setfacl -e compartida ## Editing NFSv4 ACL for directory: /mnt/compartida A::OWNER@:rwaDxtTcCy A::GROUP@:rwaDxtcy A::EVERYONE@:tcy A:fdi:OWNER@:rwaDxtTcCy A:fdi:GROUP@:rwaDxtcy A:fdi:EVERYONE@:tcy :wq Failed setxattr operation: Operation not permitted The underlying file system is: /dev/disk/by-id/ata-Maxtor_6V200E0_V40FV13G-part2 / ext4 acl,user_xattr 1 1 and works fine with POSIX ACL's. Why are the nfs4 ACE's 'not permitted'? Thanks, L x -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

1 0

[opensuse] Dual monitor config (12.2 GeForce GT520)
by Dylan 04 Oct '12

04 Oct '12

I am trying to set up dual monitors on my newly installed 12.2. I have a GeForce GT520, using the nvidia driver (x11-video-nvidiaG02 304.43-2.0.1 from obs://build.suse.de/home:sndirsch:drivers) The monitors are attached to VGA-0 and HDMI-0 (output of xrandr below) The monitor on VGA-0 displays correctly, but with the screen on HDMI-0 the desktop extends beyond the top and bottom of the physical screen. Previously, this screen was running correctly at the same resolution (but as a solo monitor on a different graphics card.) I think the problem would be related to the fact that in the previous set up, that screen was running at 60Hz, whereas now it gets automatically set to 50Hz. Any assistance would be gratefully accepted ... Dylan dylan@zen:~> xrandr --current --verbose Screen 0: minimum 8 x 8, current 2560 x 1024, maximum 16384 x 16384 <SNIP> VGA-0 connected 1280x1024+1280+0 (0x27d) normal (normal left inverted right x axis y axis) 338mm x 270mm Identifier: 0x27c Timestamp: 56641 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 0 CRTCs: 1 0 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: EDID: 00ffffffffffff004c2d5a0037314847 1e0c01030f221b8cea6f86a25a4d9424 1a4f54bfef8081806140454031400101 010101010101302a009851002a403070 1300520e1100001e000000fd0038551e 510d000a202020202020000000fc0053 796e634d61737465720a2020000000ff 0048344c543730363031350a20200025 SignalFormat: VGA supported: VGA ConnectorType: VGA ConnectorNumber: 2 (0x00000002) _ConnectorLocation: 2 (0x00000002) 1280x1024 (0x27d) 108.0MHz +HSync +VSync *current +preferred h: width 1280 start 1328 end 1440 total 1688 skew 0 clock 64.0KHz v: height 1024 start 1025 end 1028 total 1066 clock 60.0Hz 1280x1024 (0x27e) 135.0MHz +HSync +VSync h: width 1280 start 1296 end 1440 total 1688 skew 0 clock 80.0KHz v: height 1024 start 1025 end 1028 total 1066 clock 75.0Hz 1024x768 (0x27f) 78.8MHz +HSync +VSync h: width 1024 start 1040 end 1136 total 1312 skew 0 clock 60.0KHz v: height 768 start 769 end 772 total 800 clock 75.0Hz 1024x768 (0x280) 75.0MHz -HSync -VSync h: width 1024 start 1048 end 1184 total 1328 skew 0 clock 56.5KHz v: height 768 start 771 end 777 total 806 clock 70.1Hz 1024x768 (0x281) 65.0MHz -HSync -VSync h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz v: height 768 start 771 end 777 total 806 clock 60.0Hz 800x600 (0x282) 49.5MHz +HSync +VSync h: width 800 start 816 end 896 total 1056 skew 0 clock 46.9KHz v: height 600 start 601 end 604 total 625 clock 75.0Hz 800x600 (0x283) 50.0MHz +HSync +VSync h: width 800 start 856 end 976 total 1040 skew 0 clock 48.1KHz v: height 600 start 637 end 643 total 666 clock 72.2Hz 800x600 (0x284) 40.0MHz +HSync +VSync h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz v: height 600 start 601 end 605 total 628 clock 60.3Hz 800x600 (0x285) 36.0MHz +HSync +VSync h: width 800 start 824 end 896 total 1024 skew 0 clock 35.2KHz v: height 600 start 601 end 603 total 625 clock 56.2Hz 640x480 (0x286) 31.5MHz -HSync -VSync h: width 640 start 656 end 720 total 840 skew 0 clock 37.5KHz v: height 480 start 481 end 484 total 500 clock 75.0Hz 640x480 (0x287) 31.5MHz -HSync -VSync h: width 640 start 656 end 696 total 832 skew 0 clock 37.9KHz v: height 480 start 481 end 484 total 520 clock 72.8Hz 640x480 (0x288) 25.2MHz -HSync -VSync h: width 640 start 648 end 744 total 800 skew 0 clock 31.5KHz v: height 480 start 482 end 484 total 525 clock 60.0Hz 640x480 (0x289) 25.2MHz -HSync -VSync h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz v: height 480 start 490 end 492 total 525 clock 59.9Hz <SNIP> HDMI-0 connected 1280x720+0+0 (0x28c) normal (normal left inverted right x axis y axis) 708mm x 398mm Identifier: 0x28b Timestamp: 56641 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 1 CRTCs: 1 0 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: EDID: 00ffffffffffff003674121161b90b03 310f0103804628782a3f44a654469924 13484bbfee0001010101010101010101 010101010101011d00bc52d01e20b828 5540c48e2100001e000000fd00384c1f 3d08000a202020202020000000ff0035 32353030303030300a202020000000fc 00564342347878785f414d3030300155 02031871451112931401230907078301 000065030c001000011d80d0721c1620 102c2580c48e2100009e8c0ad0902040 31200c405500c48e210000188c0ad090 204031200c405500138e210000180000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000007 SignalFormat: TMDS supported: TMDS ConnectorType: HDMI ConnectorNumber: 1 (0x00000001) _ConnectorLocation: 1 (0x00000001) 1280x720 (0x28c) 74.2MHz +HSync +VSync *current +preferred h: width 1280 start 1720 end 1760 total 1980 skew 0 clock 37.5KHz v: height 720 start 725 end 730 total 750 clock 50.0Hz 1920x1080 (0x28d) 74.2MHz +HSync +VSync Interlace h: width 1920 start 2448 end 2492 total 2640 skew 0 clock 28.1KHz v: height 1080 start 1084 end 1094 total 1124 clock 25.0Hz 1024x768 (0x27f) 78.8MHz +HSync +VSync h: width 1024 start 1040 end 1136 total 1312 skew 0 clock 60.0KHz v: height 768 start 769 end 772 total 800 clock 75.0Hz 1024x768 (0x280) 75.0MHz -HSync -VSync h: width 1024 start 1048 end 1184 total 1328 skew 0 clock 56.5KHz v: height 768 start 771 end 777 total 806 clock 70.1Hz 1024x768 (0x281) 65.0MHz -HSync -VSync h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz v: height 768 start 771 end 777 total 806 clock 60.0Hz 800x600 (0x282) 49.5MHz +HSync +VSync h: width 800 start 816 end 896 total 1056 skew 0 clock 46.9KHz v: height 600 start 601 end 604 total 625 clock 75.0Hz 800x600 (0x283) 50.0MHz +HSync +VSync h: width 800 start 856 end 976 total 1040 skew 0 clock 48.1KHz v: height 600 start 637 end 643 total 666 clock 72.2Hz 800x600 (0x284) 40.0MHz +HSync +VSync h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz v: height 600 start 601 end 605 total 628 clock 60.3Hz 800x600 (0x285) 36.0MHz +HSync +VSync h: width 800 start 824 end 896 total 1024 skew 0 clock 35.2KHz v: height 600 start 601 end 603 total 625 clock 56.2Hz 720x576 (0x28e) 27.0MHz -HSync -VSync h: width 720 start 732 end 796 total 864 skew 0 clock 31.2KHz v: height 576 start 581 end 586 total 625 clock 50.0Hz 640x480 (0x286) 31.5MHz -HSync -VSync h: width 640 start 656 end 720 total 840 skew 0 clock 37.5KHz v: height 480 start 481 end 484 total 500 clock 75.0Hz 640x480 (0x287) 31.5MHz -HSync -VSync h: width 640 start 656 end 696 total 832 skew 0 clock 37.9KHz v: height 480 start 481 end 484 total 520 clock 72.8Hz 640x480 (0x289) 25.2MHz -HSync -VSync h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz v: height 480 start 490 end 492 total 525 clock 59.9Hz 640x480 (0x28f) 25.2MHz -HSync -VSync h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz v: height 480 start 490 end 492 total 525 clock 59.9Hz -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

6 11

[opensuse] Upgrade from 11.4 to 12.1, cciss module
by Claudio ML 04 Oct '12

04 Oct '12

Hello all, I have a system with a Smart Array 5i/532 with OpenSuSE 11.3. Now i want to upgrade this to OpenSuSE 12.2, but i have a problem. I have noticied from another system with OpenSuSE 12.2, of a module change, from cciss to hpsa, and a change from /dev/cciss to /dev/sdx. Now, my questions are basically 2: - When i do the upgrade of that system, will be used the hpsa module? It will be used for an Smart Array 5i/532? - If the hpsa module will be used, and the hard disk device change from /dev/cciss to /dev/sdx, what i can do to make the system bootable? I need a detailed list of operations to be done in this case, the last time it is happened the only solution i have found is to re-install all the system... Cordially, Claudio Prono. -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

2 4

[opensuse] rsyslog drops thousands of messages.
by Carlos E. R. 04 Oct '12

04 Oct '12

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 When I fetch mail with fetchmail, I see this: <5.6> 2012-09-12 17:09:03 Telcontar rsyslogd-2177 - - - imuxsock begins to drop messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:07 Telcontar rsyslogd-2177 - - - imuxsock lost 187 messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:09 Telcontar rsyslogd-2177 - - - imuxsock begins to drop messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:13 Telcontar rsyslogd-2177 - - - imuxsock lost 226 messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:15 Telcontar rsyslogd-2177 - - - imuxsock begins to drop messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:19 Telcontar rsyslogd-2177 - - - imuxsock lost 144 messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:21 Telcontar rsyslogd-2177 - - - imuxsock begins to drop messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:25 Telcontar rsyslogd-2177 - - - imuxsock lost 248 messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:27 Telcontar rsyslogd-2177 - - - imuxsock begins to drop messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:31 Telcontar rsyslogd-2177 - - - imuxsock lost 196 messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:35 Telcontar rsyslogd-2177 - - - imuxsock begins to drop messages from pid 21238 due to rate-limiting <5.6> 2012-09-12 17:09:37 Telcontar rsyslogd-2177 - - - imuxsock lost 119 messages from pid 21238 due to rate-limiting The PID is that of fetchmail. How can avoid that? This is with openSUSE 12.1 - -- Cheers, Carlos E. R. -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.18 (GNU/Linux) iEYEARECAAYFAlBQpsQACgkQtTMYHG2NR9XAKACfXrYylbVLZUuJsFaMnxBUYdFk pO0An3FzGU4XJHgyR/lqJO0oXpW/38no =x9Hz -----END PGP SIGNATURE----- -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

11 49

[opensuse] No interaction with Android over bluetooth
by Gary Trotcko 04 Oct '12

04 Oct '12

Hi folks. I came across the odd behavior of my bluetooth system on 2 laptops -- HP Probook 4330s running Opensue 12.1 x86_64 and Asus x44 with 32 bit Opensuse 12.1. I have 2 Samsung smartphones, Galaxy S GT-I9000 and my wife's Galaxy Mini and any attempts to transfer data over bluetooth in both directions between my laptops and any of these handsets are failng with such error messages: 'Connection reset by peer (104)', but previously these devices were successfully discovered for each other. In other hand with my old Nokias (6220 Classic, N810) the laptops' bluetooth works just fine without any issues. I guess it's not a matter of Android but Suse due the fact that I can normally transfer files from my desktop (Fedora) to the same Samsung handsets over USB bluetooth dongle. Additionally to transfer issue I have a faling tethering with Samsung too. My system logs don't contain any useful info at least I couldn't find it out. Is anyone here who can tell me if it bug and could it be reported previously. Googling it haven't brought any mention for such behavior. I will appreciate any suggestions for solving this trouble. Thanks. My HP Probook 4330s: http://dl.dropbox.com/u/3067546/hp4330s_conf.txt My Samsung Galaxy S GT-I9000 runs stock firmware Gingerbread 2.3.6 and just in case I get android logs with logcollector: http://dl.dropbox.com/u/3067546/androidlogfile.txt -- Best Regards, Gary Trotcko -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

1 1

[opensuse] konqueror broken after update
by eddie 03 Oct '12

03 Oct '12

Personally, I've never liked dolphin and preferred konqueror. However, since running an update, konqueror no longer works. I get the following error message. There was an error loading the module Sidebar. The diagnostics is: The plugin 'konq_sidebar' uses an incompatible KDE library (4.9.2 "release 511"). Any thoughts? -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

2 3

[opensuse] screensaver
by e-letter 03 Oct '12

03 Oct '12

Readers, How to find the screensaver settings for the gnome desktop? The 'systems settings' application does not show an option. -- opensuse122gnome -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

3 2

[opensuse] SuSE branded XFCE
by ellanios82 03 Oct '12

03 Oct '12

Hello openSuSErs SuSE branded XFCE __________________ - this is a 'Superior desktop' . . . very Nice . . . Congrats :)) .......... best regards -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

1 0

[opensuse] OS 12.2 KDE and reboot options
by JC Francois 03 Oct '12

03 Oct '12

Hi, I just upgraded my OS 12.1 installation to OS 12.2 on my dual boot (Win 7 and OS) system and everything went smoothly. The bootloader seems to still be GRUB 0.97 while I expected 2.0 but that is really not a big deal. What I have lost (and miss) are the options that I used to get when I clicked long on the "restart computer" button. I used to see the list of the GRUB partitions displayed and had the choice to select what partition I wanted to boot back in (for example reboot in Win7). Is there any way to restore that functionality? Thanks, /~JC -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

2 2

[opensuse] Can`t start KDE in opesuse 12.2
by Gunnar 03 Oct '12

03 Oct '12

I have "lost" my Opensuse. I have tried to upgrade from 12.1 to 12.2. After the upgrade was done, I got an error, and that I had to: RPM --rebuilddb. No I can`t log in, it seem that the graphic system are broken. I can log in to consol, but no KDE start up. Gunnar -- To unsubscribe, e-mail: opensuse+unsubscribe(a)opensuse.org To contact the owner, e-mail: opensuse+owner(a)opensuse.org

3 6