Suse 11.3, Kernel 2.6.34.7-0.7, Fehler bei Laden von Modul fcpci
Hallo, folgende Fehlermeldung erscheint: modprobe fcpci FATAL: Error inserting fcpci (/lib/modules/2.6.34.7-0.7-xen/updates/fcpci.ko): Device or resource busy Sämtliche Versuche in den Foren waren erfolglos Ich hoffe, dass mir jemand helfen kann. Vielen Dank -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org
On 28.01.2011, PAP wrote:
FATAL: Error inserting fcpci (/lib/modules/2.6.34.7-0.7-xen/updates/fcpci.ko): Device or resource busy
Kannst du bitte mal die Ausgabe von "lspci -v" posten? Und bitte auch den fuer die Karte relevanten Abschnitt aus der Ausgabe von "dmesg". -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org
Hallo Herr Diehl, vielen Dank für die Antwort. Die Antwort hane unter die jeweilige Zeile kopiert. Mit freundlichen Grüßen, Peter Am Freitag, 28. Januar 2011, 09:32:41 schrieb Heinz Diehl:
On 28.01.2011, PAP wrote:
FATAL: Error inserting fcpci (/lib/modules/2.6.34.7-0.7-xen/updates/fcpci.ko): Device or resource busy
Kannst du bitte mal die Ausgabe von "lspci -v" posten?
linux-1:~ # lspci -v 00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a4) Subsystem: Dell PowerEdge T105 Memory Controller Flags: bus master, 66MHz, fast devsel, latency 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed- 00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev f1) Subsystem: Dell PowerEdge T105 ISA Bridge Flags: bus master, 66MHz, fast devsel, latency 0 I/O ports at 8c00 [size=1K] 00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2) Subsystem: Dell PowerEdge T105 SMBus Flags: 66MHz, fast devsel, IRQ 10 I/O ports at 2080 [size=32] I/O ports at 2040 [size=64] I/O ports at 2000 [size=64] Capabilities: [44] Power Management version 2 Kernel driver in use: nForce2_smbus 00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Dell PowerEdge T105 onboard USB Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20 Memory at d0000000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a4) (prog-if 20 [EHCI]) Subsystem: Dell PowerEdge T105 onboard USB Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at d0001000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO]) Subsystem: Dell PowerEdge T105 Serial ATA Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 I/O ports at 20f0 [size=8] I/O ports at 20e0 [size=4] I/O ports at 20d0 [size=8] I/O ports at 20c0 [size=4] I/O ports at 20b0 [size=16] Memory at d0002000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: sata_nv 00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO]) Subsystem: Dell PowerEdge T105 Serial ATA Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 I/O ports at 2440 [size=8] I/O ports at 2430 [size=4] I/O ports at 2420 [size=8] I/O ports at 2410 [size=4] I/O ports at 2400 [size=16] Memory at d0003000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: sata_nv 00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev f2) (prog-if 00 [Normal decode]) Flags: bus master, 66MHz, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 00003000-00003fff Memory behind bridge: d0100000-d01fffff Prefetchable memory behind bridge: d8000000-dfffffff 00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00linux-1:~ # lspci -v 00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a4) Subsystem: Dell PowerEdge T105 Memory Controller Flags: bus master, 66MHz, fast devsel, latency 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed- 00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev f1) Subsystem: Dell PowerEdge T105 ISA Bridge Flags: bus master, 66MHz, fast devsel, latency 0 I/O ports at 8c00 [size=1K] 00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2) Subsystem: Dell PowerEdge T105 SMBus Flags: 66MHz, fast devsel, IRQ 10 I/O ports at 2080 [size=32] I/O ports at 2040 [size=64] I/O ports at 2000 [size=64] Capabilities: [44] Power Management version 2 Kernel driver in use: nForce2_smbus 00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Dell PowerEdge T105 onboard USB Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20 Memory at d0000000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a4) (prog-if 20 [EHCI]) Subsystem: Dell PowerEdge T105 onboard USB Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at d0001000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO]) Subsystem: Dell PowerEdge T105 Serial ATA Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 I/O ports at 20f0 [size=8] I/O ports at 20e0 [size=4] I/O ports at 20d0 [size=8] I/O ports at 20c0 [size=4] I/O ports at 20b0 [size=16] Memory at d0002000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: sata_nv 00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO]) Subsystem: Dell PowerEdge T105 Serial ATA Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 I/O ports at 2440 [size=8] I/O ports at 2430 [size=4] I/O ports at 2420 [size=8] I/O ports at 2410 [size=4] I/O ports at 2400 [size=16] Memory at d0003000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: sata_nv 00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev f2) (prog-if 00 [Normal decode]) Flags: bus master, 66MHz, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 00003000-00003fff Memory behind bridge: d0100000-d01fffff Prefetchable memory behind bridge: d8000000-dfffffff 00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Memory behind bridge: d0200000-d02fffff Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [160] Advanced Error Reporting Kernel driver in use: pcieport 00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [160] Advanced Error Reporting Kernel driver in use: pcieport 00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [160] Advanced Error Reporting Kernel driver in use: pcieport 00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [160] Advanced Error Reporting Kernel driver in use: pcieport 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp 01:07.0 Network controller: AVM GmbH Fritz!PCI v2.0 ISDN (rev 01) Subsystem: AVM GmbH Fritz!PCI v2.0 ISDN Flags: medium devsel, IRQ 17 Memory at d0110000 (32-bit, non-prefetchable) [size=32] I/O ports at 3400 [size=32] Capabilities: [40] Power Management version 2 Kernel driver in use: fcpci 01:08.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02) (prog- if 00 [VGA controller]) Subsystem: Dell PowerEdge T105 Embedded ATI ES1000 Flags: bus master, stepping, fast Back2Back, medium devsel, latency 66, IRQ 19 Memory at d8000000 (32-bit, prefetchable) [size=128M] I/O ports at 3000 [size=256] Memory at d0100000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at d0120000 [disabled] [size=128K] Capabilities: [50] Power Management version 2 Kernel driver in use: radeon 02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Dell PowerEdge T105 Broadcom NetXtreme 5722 Flags: bus master, fast devsel, latency 0, IRQ 419 Memory at d0200000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data Capabilities: [58] Vendor Specific Information: Len=78 <?> Capabilities: [e8] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 00-1e-c9-ff-fe-28-99-37 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: tg3 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Memory behind bridge: d0200000-d02fffff Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [160] Advanced Error Reporting Kernel driver in use: pcieport 00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [160] Advanced Error Reporting Kernel driver in use: pcieport 00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [160] Advanced Error Reporting Kernel driver in use: pcieport 00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [160] Advanced Error Reporting Kernel driver in use: pcieport 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp 01:07.0 Network controller: AVM GmbH Fritz!PCI v2.0 ISDN (rev 01) Subsystem: AVM GmbH Fritz!PCI v2.0 ISDN Flags: medium devsel, IRQ 17 Memory at d0110000 (32-bit, non-prefetchable) [size=32] I/O ports at 3400 [size=32] Capabilities: [40] Power Management version 2 Kernel driver in use: fcpci 01:08.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02) (prog- if 00 [VGA controller]) Subsystem: Dell PowerEdge T105 Embedded ATI ES1000 Flags: bus master, stepping, fast Back2Back, medium devsel, latency 66, IRQ 19 Memory at d8000000 (32-bit, prefetchable) [size=128M] I/O ports at 3000 [size=256] Memory at d0100000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at d0120000 [disabled] [size=128K] Capabilities: [50] Power Management version 2 Kernel driver in use: radeon 02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Dell PowerEdge T105 Broadcom NetXtreme 5722 Flags: bus master, fast devsel, latency 0, IRQ 419 Memory at d0200000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data Capabilities: [58] Vendor Specific Information: Len=78 <?> Capabilities: [e8] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 00-1e-c9-ff-fe-28-99-37 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: tg3
Und bitte auch den fuer die Karte relevanten Abschnitt aus der Ausgabe von "dmesg".
.0-4/input0 [ 2.731627] usbcore: registered new interface driver usbhid [ 2.731629] usbhid: USB HID core driver [ 2.761656] EXT4-fs (sda5): mounted filesystem with ordered data mode [ 3.016024] usb 2-7: new low speed USB device using ohci_hcd and address 3 [ 3.219038] usb 2-7: New USB device found, idVendor=062a, idProduct=0000 [ 3.219041] usb 2-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.228314] input: HID 062a:0000 as /devices/pci0000:00/0000:00:02.0/usb2/2-7/2-7:1.0/input/input1 [ 3.228380] generic-usb 0003:062A:0000.0002: input,hidraw1: USB HID v1.10 Mouse [HID 062a:0000] on usb-0000:00:02.0-7/input0 [ 4.809755] udev: starting version 157 [ 4.959911] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 4.962569] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 5.106540] i2c i2c-1: nForce2 SMBus adapter at 0x2040 [ 5.106555] i2c i2c-2: nForce2 SMBus adapter at 0x2000 [ 5.108497] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2 [ 5.108543] ACPI: Power Button [PWRB] [ 5.108619] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 5.108644] ACPI: Power Button [PWRF] [ 5.128047] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 5.128084] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 5.128113] scsi 2:0:0:0: Attached scsi generic sg2 type 5 [ 5.174557] sr0: scsi3-mmc drive: 8x/48x writer cd/rw xa/form2 cdda tray [ 5.174561] Uniform CD-ROM driver Revision: 3.20 [ 5.174668] sr 2:0:0:0: Attached scsi CD-ROM sr0 [ 5.273621] Modular ISDN core version 1.1.21 [ 5.273710] NET: Registered protocol family 34 [ 5.315219] tg3.c:v3.108 (February 17, 2010) [ 5.315700] input: PC Speaker as /devices/platform/pcspkr/input/input4 [ 5.316702] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141 [ 5.318172] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 18 [ 5.318178] alloc irq_desc for 18 on node -1 [ 5.318180] alloc kstat_irqs on node -1 [ 5.318197] tg3 0000:02:00.0: PCI INT A -> Link[LNK2] -> GSI 18 (level, low) -> IRQ 18 [ 5.318209] tg3 0000:02:00.0: setting latency timer to 64 [ 5.338097] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 5.338252] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 5.338930] tg3 0000:02:00.0: eth0: Tigon3 [partno(BCM95722) rev a200] (PCI Express) MAC address 00:1e:c9:28:99:37 [ 5.338936] tg3 0000:02:00.0: eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1]) [ 5.338939] tg3 0000:02:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 5.338942] tg3 0000:02:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit] [ 5.347705] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 5.350536] mISDNipac module version 2.0 [ 5.365556] AVM Fritz PCI driver Rev. 2.1 [ 5.366174] ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 17 [ 5.366180] alloc irq_desc for 17 on node -1 [ 5.366182] alloc kstat_irqs on node -1 [ 5.366194] fcpci 0000:01:07.0: PCI INT A -> Link[LNK4] -> GSI 17 (level, low) -> IRQ 17 [ 5.366197] mISDN: found adapter Fritz!Card PCI v2 at 0000:01:07.0 [ 5.366208] AVM.1: AVM Fritz!CARD PCIv2 config irq:17 base:0x3400 [ 5.388032] AVM 1 cards installed DEBUG [ 5.533992] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 6.402395] Adding 6072564k swap on /dev/sda3. Priority:-1 extents:1 across:6072564k [ 6.650816] device-mapper: uevent: version 1.0.3 [ 6.651014] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com [ 7.404699] loop: module loaded [ 7.650523] EXT4-fs (sda9): mounted filesystem with ordered data mode [ 7.716310] EXT4-fs (sda6): mounted filesystem with ordered data mode [ 7.761698] EXT4-fs (sda8): mounted filesystem with ordered data mode [ 7.814978] EXT4-fs (sda7): mounted filesystem with ordered data mode [ 10.009071] type=1505 audit(1296197342.217:2): operation="profile_load" pid=1163 name=/bin/ping [ 10.065247] type=1505 audit(1296197342.274:3): operation="profile_load" pid=1167 name=/sbin/klogd [ 10.173741] type=1505 audit(1296197342.381:4): operation="profile_load" pid=1168 name=/sbin/syslog-ng [ 10.281297] type=1505 audit(1296197342.490:5): operation="profile_load" pid=1169 name=/sbin/syslogd [ 10.397635] type=1505 audit(1296197342.605:6): operation="profile_load" pid=1170 name=/usr/sbin/avahi-daemon [ 10.494982] type=1505 audit(1296197342.702:7): operation="profile_load" pid=1171 name=/usr/sbin/identd [ 10.602638] type=1505 audit(1296197342.809:8): operation="profile_load" pid=1172 name=/usr/sbin/mdnsd [ 10.727924] type=1505 audit(1296197342.934:9): operation="profile_load" pid=1173 name=/usr/sbin/nscd [ 10.898438] type=1505 audit(1296197343.105:10): operation="profile_load" pid=1174 name=/usr/sbin/ntpd [ 11.014949] type=1505 audit(1296197343.222:11): operation="profile_load" pid=1175 name=/usr/sbin/traceroute [ 11.791461] CAPI 2.0 started up with major 68 (middleware+capifs) [ 18.258476] type=1503 audit(1296197350.465:12): operation="change_hat" info="unconfined" error=-1 pid=1673 [ 18.258498] type=1503 audit(1296197350.465:13): operation="change_hat" info="unconfined" error=-1 pid=1673 [ 22.761726] fcpci: module license 'Proprietary' taints kernel. [ 22.761732] Disabling lock debugging due to kernel taint [ 22.766161] fcpci: AVM FRITZ!Card PCI driver, revision 0.7.2 [ 22.766164] fcpci: (fcpci built on Jan 10 2011 at 12:18:45) [ 22.766165] fcpci: -- 64 bit CAPI driver -- [ 22.766171] Error: Driver 'fcpci' is already registered, aborting... [ 22.891705] fcpci: AVM FRITZ!Card PCI driver, revision 0.7.2 [ 22.891709] fcpci: (fcpci built on Jan 10 2011 at 12:18:45) [ 22.891711] fcpci: -- 64 bit CAPI driver -- [ 22.891716] Error: Driver 'fcpci' is already registered, aborting... [ 23.036445] ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded [ 25.407047] Bridge firewalling registered [ 25.420385] alloc irq_desc for 419 on node 0 [ 25.420389] alloc kstat_irqs on node 0 [ 25.420394] tg3 0000:02:00.0: irq 419 (275) for MSI/MSI-X [ 25.453477] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 25.455757] device eth0 entered promiscuous mode [ 27.121801] tg3 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex [ 27.121805] tg3 0000:02:00.0: eth0: Flow control is on for TX and on for RX [ 27.122170] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 27.122214] br0: port 1(eth0) entering forwarding state [ 29.569933] BIOS EDD facility v0.16 2004-Jun-25, 2 devices found [ 32.371850] Event-channel device installed. [ 33.045302] usbcore: registered new interface driver usbback [ 35.740013] br0: no IPv6 routers present [ 37.812012] eth0: no IPv6 routers present [ 40.329645] alloc irq_desc for 428 on node 0 [ 40.329648] alloc kstat_irqs on node 0 [ 40.329690] alloc irq_desc for 429 on node 0 [ 40.329691] alloc kstat_irqs on node 0 [ 40.329731] alloc irq_desc for 430 on node 0 [ 40.329733] alloc kstat_irqs on node 0 [ 40.338233] alloc irq_desc for 431 on node 0 [ 40.338236] alloc kstat_irqs on node 0 [ 40.338262] suspend: event channel 24 [ 125.235627] fcpci: AVM FRITZ!Card PCI driver, revision 0.7.2 [ 125.235632] fcpci: (fcpci built on Jan 10 2011 at 12:18:45) [ 125.235634] fcpci: -- 64 bit CAPI driver -- [ 125.235639] Error: Driver 'fcpci' is already registered, aborting... -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org
On 28.01.2011, PAP wrote:
01:07.0 Network controller: AVM GmbH Fritz!PCI v2.0 ISDN (rev 01) Subsystem: AVM GmbH Fritz!PCI v2.0 ISDN Flags: medium devsel, IRQ 17 Memory at d0110000 (32-bit, non-prefetchable) [size=32] I/O ports at 3400 [size=32] Capabilities: [40] Power Management version 2 Kernel driver in use: fcpci
Das ist der relevante Eintrag. Die letzte Zeile sagt, dass fcpci bereits benutzt wird von deiner Fritz-Karte.
[ 22.761726] fcpci: module license 'Proprietary' taints kernel. [ 22.761732] Disabling lock debugging due to kernel taint [ 22.766161] fcpci: AVM FRITZ!Card PCI driver, revision 0.7.2 [ 22.766164] fcpci: (fcpci built on Jan 10 2011 at 12:18:45) [ 22.766165] fcpci: -- 64 bit CAPI driver -- [ 22.766171] Error: Driver 'fcpci' is already registered, aborting... [ 22.891705] fcpci: AVM FRITZ!Card PCI driver, revision 0.7.2 [ 22.891709] fcpci: (fcpci built on Jan 10 2011 at 12:18:45) [ 22.891711] fcpci: -- 64 bit CAPI driver -- [ 22.891716] Error: Driver 'fcpci' is already registered, aborting...
Hier wird versucht, den Treiber nochmals zu laden, und jetzt wird klar, warum die Fehlermeldung kommt: wie oben ersichtlich ist, ist der Treiber bereits geladen. Du hast also zwei Moeglichkeiten: die Meldung ignorieren, oder nachzusehen, wer oder was da nochmal laden will. Es kann auch sein, dass der Treiber fest in den Kernel einkompiliert ist, und irgendwas den nochmal als Modul nachladen will. Dann kannst du ihn in /etc/modprobe.d/blacklist deaktivieren. Alternativ dazu kannst du auch den Prozess finden, der da nochmal laden will. -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org
On 28.01.2011, Heinz Diehl wrote:
Es kann auch sein, dass der Treiber fest in den Kernel einkompiliert ist, und irgendwas den nochmal als Modul nachladen will.
Vergiss diesen Satz, der Treiber ist proprietaer und deswegen nicht im kernel enthalten. Wenn deine Fritzcard funktioniert, wuerde ich die Meldung ignorieren, irgendein Prozess versucht einfach, den Treiber nochmal zu laden. -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Heinz Diehl [28.01.2011 22:28]:
On 28.01.2011, Heinz Diehl wrote:
Es kann auch sein, dass der Treiber fest in den Kernel einkompiliert ist, und irgendwas den nochmal als Modul nachladen will.
Vergiss diesen Satz, der Treiber ist proprietaer und deswegen nicht im kernel enthalten. Wenn deine Fritzcard funktioniert, wuerde ich die Meldung ignorieren, irgendein Prozess versucht einfach, den Treiber nochmal zu laden.
Ich weiß es jetzt nicht sicher, aber ist das nicht eine Spezialität der Fritz-Karten, dass sie drei Dingslinge laden, der erste lädt einen Treiber, und die beiden nächsten versuchen das auch und scheitern (natürlich)? Ich meine, dass ich sowas vor Jahren auch hatte, als ich noch Fritzen brauchte... Jedenfalls kommt mir die Sache sehr bekannt vor. Gruß Werner -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.15 (GNU/Linux) Comment: Using GnuPG with SUSE - http://enigmail.mozdev.org/ iEYEARECAAYFAk1GeRMACgkQk33Krq8b42NH/QCfVBVoZf3Gf9ZJdBK18QeuxVUC 5JkAmwfnjxdycn1fi+OwsikiNyYoJ86G =VVlq -----END PGP SIGNATURE----- -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org
Am Freitag, 28. Januar 2011, 09:32:41 schrieb Heinz Diehl:
On 28.01.2011, PAP wrote:
FATAL: Error inserting fcpci (/lib/modules/2.6.34.7-0.7-xen/updates/fcpci.ko): Device or resource busy
Vielen Dank für deine Antwort, Mit freundlichen Grüßen, Peter
Kannst du bitte mal die Ausgabe von "lspci -v" posten?
linux-1:~ # lspci -v 00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a4) Subsystem: Dell PowerEdge T105 Memory Controller Flags: bus master, 66MHz, fast devsel, latency 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed- 00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev f1) Subsystem: Dell PowerEdge T105 ISA Bridge Flags: bus master, 66MHz, fast devsel, latency 0 I/O ports at 8c00 [size=1K] 00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2) Subsystem: Dell PowerEdge T105 SMBus Flags: 66MHz, fast devsel, IRQ 10 I/O ports at 2080 [size=32] I/O ports at 2040 [size=64] I/O ports at 2000 [size=64] Capabilities: [44] Power Management version 2 Kernel driver in use: nForce2_smbus 00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Dell PowerEdge T105 onboard USB Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20 Memory at d0000000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a4) (prog-if 20 [EHCI]) Subsystem: Dell PowerEdge T105 onboard USB Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at d0001000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO]) Subsystem: Dell PowerEdge T105 Serial ATA Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 I/O ports at 20f0 [size=8] I/O ports at 20e0 [size=4] I/O ports at 20d0 [size=8] I/O ports at 20c0 [size=4] I/O ports at 20b0 [size=16] Memory at d0002000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: sata_nv 00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO]) Subsystem: Dell PowerEdge T105 Serial ATA Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 I/O ports at 2440 [size=8] I/O ports at 2430 [size=4] I/O ports at 2420 [size=8] I/O ports at 2410 [size=4] I/O ports at 2400 [size=16] Memory at d0003000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: sata_nv 00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev f2) (prog-if 00 [Normal decode]) Flags: bus master, 66MHz, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 00003000-00003fff Memory behind bridge: d0100000-d01fffff Prefetchable memory behind bridge: d8000000-dfffffff 00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Memory behind bridge: d0200000-d02fffff Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [160] Advanced Error Reporting Kernel driver in use: pcieport 00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [160] Advanced Error Reporting Kernel driver in use: pcieport 00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev f3) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [160] Advanced Error Reporting Kernel driver in use: pcieport 00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [160] Advanced Error Reporting Kernel driver in use: pcieport 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp 01:07.0 Network controller: AVM GmbH Fritz!PCI v2.0 ISDN (rev 01) Subsystem: AVM GmbH Fritz!PCI v2.0 ISDN Flags: medium devsel, IRQ 17 Memory at d0110000 (32-bit, non-prefetchable) [size=32] I/O ports at 3400 [size=32] Capabilities: [40] Power Management version 2 Kernel driver in use: fcpci 01:08.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02) (prog- if 00 [VGA controller]) Subsystem: Dell PowerEdge T105 Embedded ATI ES1000 Flags: bus master, stepping, fast Back2Back, medium devsel, latency 66, IRQ 19 Memory at d8000000 (32-bit, prefetchable) [size=128M] I/O ports at 3000 [size=256] Memory at d0100000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at d0120000 [disabled] [size=128K] Capabilities: [50] Power Management version 2 Kernel driver in use: radeon 02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Dell PowerEdge T105 Broadcom NetXtreme 5722 Flags: bus master, fast devsel, latency 0, IRQ 419 Memory at d0200000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data Capabilities: [58] Vendor Specific Information: Len=78 <?> Capabilities: [e8] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 00-1e-c9-ff-fe-28-99-37 Capabilities: [16c] Power Budgeting Kernel driver in use: tg3
Und bitte auch den fuer die Karte relevanten Abschnitt aus der Ausgabe von "dmesg".
.0-4/input0 [ 2.731627] usbcore: registered new interface driver usbhid [ 2.731629] usbhid: USB HID core driver [ 2.761656] EXT4-fs (sda5): mounted filesystem with ordered data mode [ 3.016024] usb 2-7: new low speed USB device using ohci_hcd and address 3 [ 3.219038] usb 2-7: New USB device found, idVendor=062a, idProduct=0000 [ 3.219041] usb 2-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.228314] input: HID 062a:0000 as /devices/pci0000:00/0000:00:02.0/usb2/2-7/2-7:1.0/input/input1 [ 3.228380] generic-usb 0003:062A:0000.0002: input,hidraw1: USB HID v1.10 Mouse [HID 062a:0000] on usb-0000:00:02.0-7/input0 [ 4.809755] udev: starting version 157 [ 4.959911] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 4.962569] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 5.106540] i2c i2c-1: nForce2 SMBus adapter at 0x2040 [ 5.106555] i2c i2c-2: nForce2 SMBus adapter at 0x2000 [ 5.108497] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2 [ 5.108543] ACPI: Power Button [PWRB] [ 5.108619] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 5.108644] ACPI: Power Button [PWRF] [ 5.128047] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 5.128084] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 5.128113] scsi 2:0:0:0: Attached scsi generic sg2 type 5 [ 5.174557] sr0: scsi3-mmc drive: 8x/48x writer cd/rw xa/form2 cdda tray [ 5.174561] Uniform CD-ROM driver Revision: 3.20 [ 5.174668] sr 2:0:0:0: Attached scsi CD-ROM sr0 [ 5.273621] Modular ISDN core version 1.1.21 [ 5.273710] NET: Registered protocol family 34 [ 5.315219] tg3.c:v3.108 (February 17, 2010) [ 5.315700] input: PC Speaker as /devices/platform/pcspkr/input/input4 [ 5.316702] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141 [ 5.318172] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 18 [ 5.318178] alloc irq_desc for 18 on node -1 [ 5.318180] alloc kstat_irqs on node -1 [ 5.318197] tg3 0000:02:00.0: PCI INT A -> Link[LNK2] -> GSI 18 (level, low) -> IRQ 18 [ 5.318209] tg3 0000:02:00.0: setting latency timer to 64 [ 5.338097] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 5.338252] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 5.338930] tg3 0000:02:00.0: eth0: Tigon3 [partno(BCM95722) rev a200] (PCI Express) MAC address 00:1e:c9:28:99:37 [ 5.338936] tg3 0000:02:00.0: eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1]) [ 5.338939] tg3 0000:02:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 5.338942] tg3 0000:02:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit] [ 5.347705] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 5.350536] mISDNipac module version 2.0 [ 5.365556] AVM Fritz PCI driver Rev. 2.1 [ 5.366174] ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 17 [ 5.366180] alloc irq_desc for 17 on node -1 [ 5.366182] alloc kstat_irqs on node -1 [ 5.366194] fcpci 0000:01:07.0: PCI INT A -> Link[LNK4] -> GSI 17 (level, low) -> IRQ 17 [ 5.366197] mISDN: found adapter Fritz!Card PCI v2 at 0000:01:07.0 [ 5.366208] AVM.1: AVM Fritz!CARD PCIv2 config irq:17 base:0x3400 [ 5.388032] AVM 1 cards installed DEBUG [ 5.533992] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 6.402395] Adding 6072564k swap on /dev/sda3. Priority:-1 extents:1 across:6072564k [ 6.650816] device-mapper: uevent: version 1.0.3 [ 6.651014] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com [ 7.404699] loop: module loaded [ 7.650523] EXT4-fs (sda9): mounted filesystem with ordered data mode [ 7.716310] EXT4-fs (sda6): mounted filesystem with ordered data mode [ 7.761698] EXT4-fs (sda8): mounted filesystem with ordered data mode [ 7.814978] EXT4-fs (sda7): mounted filesystem with ordered data mode [ 10.009071] type=1505 audit(1296197342.217:2): operation="profile_load" pid=1163 name=/bin/ping [ 10.065247] type=1505 audit(1296197342.274:3): operation="profile_load" pid=1167 name=/sbin/klogd [ 10.173741] type=1505 audit(1296197342.381:4): operation="profile_load" pid=1168 name=/sbin/syslog-ng [ 10.281297] type=1505 audit(1296197342.490:5): operation="profile_load" pid=1169 name=/sbin/syslogd [ 10.397635] type=1505 audit(1296197342.605:6): operation="profile_load" pid=1170 name=/usr/sbin/avahi-daemon [ 10.494982] type=1505 audit(1296197342.702:7): operation="profile_load" pid=1171 name=/usr/sbin/identd [ 10.602638] type=1505 audit(1296197342.809:8): operation="profile_load" pid=1172 name=/usr/sbin/mdnsd [ 10.727924] type=1505 audit(1296197342.934:9): operation="profile_load" pid=1173 name=/usr/sbin/nscd [ 10.898438] type=1505 audit(1296197343.105:10): operation="profile_load" pid=1174 name=/usr/sbin/ntpd [ 11.014949] type=1505 audit(1296197343.222:11): operation="profile_load" pid=1175 name=/usr/sbin/traceroute [ 11.791461] CAPI 2.0 started up with major 68 (middleware+capifs) [ 18.258476] type=1503 audit(1296197350.465:12): operation="change_hat" info="unconfined" error=-1 pid=1673 [ 18.258498] type=1503 audit(1296197350.465:13): operation="change_hat" info="unconfined" error=-1 pid=1673 [ 22.761726] fcpci: module license 'Proprietary' taints kernel. [ 22.761732] Disabling lock debugging due to kernel taint [ 22.766161] fcpci: AVM FRITZ!Card PCI driver, revision 0.7.2 [ 22.766164] fcpci: (fcpci built on Jan 10 2011 at 12:18:45) [ 22.766165] fcpci: -- 64 bit CAPI driver -- [ 22.766171] Error: Driver 'fcpci' is already registered, aborting... [ 22.891705] fcpci: AVM FRITZ!Card PCI driver, revision 0.7.2 [ 22.891709] fcpci: (fcpci built on Jan 10 2011 at 12:18:45) [ 22.891711] fcpci: -- 64 bit CAPI driver -- [ 22.891716] Error: Driver 'fcpci' is already registered, aborting... [ 23.036445] ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded [ 25.407047] Bridge firewalling registered [ 25.420385] alloc irq_desc for 419 on node 0 [ 25.420389] alloc kstat_irqs on node 0 [ 25.420394] tg3 0000:02:00.0: irq 419 (275) for MSI/MSI-X [ 25.453477] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 25.455757] device eth0 entered promiscuous mode [ 27.121801] tg3 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex [ 27.121805] tg3 0000:02:00.0: eth0: Flow control is on for TX and on for RX [ 27.122170] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 27.122214] br0: port 1(eth0) entering forwarding state [ 29.569933] BIOS EDD facility v0.16 2004-Jun-25, 2 devices found [ 32.371850] Event-channel device installed. [ 33.045302] usbcore: registered new interface driver usbback [ 35.740013] br0: no IPv6 routers present [ 37.812012] eth0: no IPv6 routers present [ 40.329645] alloc irq_desc for 428 on node 0 [ 40.329648] alloc kstat_irqs on node 0 [ 40.329690] alloc irq_desc for 429 on node 0 [ 40.329691] alloc kstat_irqs on node 0 [ 40.329731] alloc irq_desc for 430 on node 0 [ 40.329733] alloc kstat_irqs on node 0 [ 40.338233] alloc irq_desc for 431 on node 0 [ 40.338236] alloc kstat_irqs on node 0 [ 40.338262] suspend: event channel 24 [ 125.235627] fcpci: AVM FRITZ!Card PCI driver, revision 0.7.2 [ 125.235632] fcpci: (fcpci built on Jan 10 2011 at 12:18:45) [ 125.235634] fcpci: -- 64 bit CAPI driver -- [ 125.235639] Error: Driver 'fcpci' is already registered, aborting... -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org
PAP wrote:
[ 5.350536] mISDNipac module version 2.0 [ 5.365556] AVM Fritz PCI driver Rev. 2.1 [ 5.366174] ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 17 [ 5.366180] alloc irq_desc for 17 on node -1 [ 5.366182] alloc kstat_irqs on node -1 [ 5.366194] fcpci 0000:01:07.0: PCI INT A -> Link[LNK4] -> GSI 17 (level, low) -> IRQ 17 [ 5.366197] mISDN: found adapter Fritz!Card PCI v2 at 0000:01:07.0
Wenn ich mich an meine 11.3 Installation zurückerinnere gab es da ein Problem mit ISDN: Kontrollier mal in /etc/modprobe.d die Datei 50-blacklist.conf; so um Zeile 230 herum ist bei mir die "ISDN-Section". Hier sollten (u.a.) die folgenden Einträge drin sein: blacklist mISDN_dsp blacklist mISDN_core blacklist mISDNipac blacklist avmfritz Wenn die nicht da sind, pack die rein. danach sollte es gehen. Andreas -- Um die Liste abzubestellen, schicken Sie eine Mail an: opensuse-de+unsubscribe@opensuse.org Um eine Liste aller verfuegbaren Kommandos zu bekommen, schicken Sie eine Mail an: opensuse-de+help@opensuse.org
participants (4)
-
Heinz Diehl -
Kyek, Andreas, VF-DE -
PAP -
Werner Flamme