Hi, beim Booten bekomme ich folgende, teilweise abweichende Treiberinfos:
(Was ist eigentlich mit der sogenannten Firmware? Muß ich da noch was
machen?)
----- Original Message -----
From: "Sebastian Huber"
Hi, und beim Booten gibt es folgende Treiberinfos:
usb-uhci.c: USB UHCI at I/O 0x1c20, IRQ 11 usb-uhci.c: USB UHCI at I/O 0x1000, IRQ 5
usb-uhci.c: Detected 2 ports usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2 usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found hub.c: USB hub found
hub.c: 2 ports detected hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
hub.c: USB new device connect on bus1/1, assigned device number 2 hub.c: USB new device connect on bus1/2, assigned device number 2
usb.c: USB device 2 (vend/prod 0x57c/0x1000) is not claimed by any active driver. usb.c: USB device 2 (vend/prod 0x57c/0x1000) is not claimed by any active driver
CAPI-driver Rev 1.1.4.1: loaded CAPI-driver Rev 1.1.4.1: loaded
fcusb2: AVM FRITZ!Card USB v2 driver, revision 0.2 fcusb2: AVM FRITZ!Card USB v2 driver, revision 0.2
fcusb2: (fcusb2 built on Aug 19 2002 at 16:02:15) fcusb2: (fcusb2 built on Jun 1 2002 at 02:15:10)
fcusb2: Loading... fcusb2: Loading...
kcapi: driver fcusb2 attached kcapi: driver fcusb2 attached
usb.c: registered new driver fcusb2 usb.c: registered new driver fcusb2
fcusb2: Driver 'fcusb2' attached to stack fcusb2: Driver 'fcusb2' attached to stack
kcapi: Controller 1: fritz-usb attached kcapi: Controller 1: fritz-usb attached
fcusb2: Loaded. fcusb2: Loaded
capifs: Rev 1.1.4.1 capi20: started up with major 68 kcapi: capi20 attached capi20: Rev 1.1.4.2: started up with major 68 (middleware+capifs) CSLIP: code copyright 1989 Regents of the University of California ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 loaded kcapi: capidrv attached kcapi: appl 1 up capidrv: Rev 1.1.4.1: loaded fcusb2: Stack version 3.09-10 kcapi: card 1 "fritz-usb" ready. kcapi: notify up contr 1 capidrv: controller 1 up capidrv-1: now up (2 B channels) capidrv-1: D2 trace enabled capi: controller 1 up
habe ich alles nicht!, dafür das: pppd[1100]: Plugin userpass.so loaded. linux pppd[1100]: userpass: $Revision: 1.3 $ linux pppd[1100]: Plugin capiplugin.so loaded. linux pppd[1100]: capiplugin: $Revision: 1.27 $ linux pppd[1100]: capiconn: 1.7 linux modprobe: modprobe: Can't locate module char-major-68 linux pppd[1100]: capiplugin: CAPI_REGISTER failed - CAPI not installed (0x1009) [No such device (19)] linux pppd[1100]: Exit.
So wie ich das sehe, laedt der USB Treiber den fcusb2 Treiber. Dieser loest mit seinem post-install das Ausfuehren des ISDN Hotplugskript aus. Das wiederum fuehrt das load-fcusb2 Skript aus, was CAPI und Karte initialisiert. Eigentlich genial.
-- Um die Liste abzubestellen, schicken Sie eine Mail an: suse-isdn-unsubscribe@suse.com Um eine Liste aller verfügbaren Kommandos zu bekommen, schicken Sie eine Mail an: suse-isdn-help@suse.com