Hi Matthias, Op 09-11-16 om 13:24 schreef Matthias Brugger:
On 11/08/2016 09:44 PM, Jogchum Reitsma wrote:
Hi,
After succeeding in getting wifi enabled on the pi 3 (see my previous posting 6th of nov., 20:31 WET, and follow ups) the next problem arises:
Would you mind to document this in the wiki, so that the next person who wants to try RPi3 doesn't have to search the list archive (or askes the question again).
I'm not sure where to put this in the wiki. The only specific place seems to me https://en.opensuse.org/HCL:Raspberry_Pi3 but that's just a bit about where to get the images, and how to install them. Seems somewhat inapporpriate to me to put is there.
every 5 minutes the wifi connection gets another hw-address, and hence another ip address... Rather inconvenient.
Dmesg spits out the following:
[ 1306.573949] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 1306.576314] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code [ 1306.576327] cfg80211: World regulatory domain updated: [ 1306.576341] cfg80211: DFS Master region: unset [ 1306.576341] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 1306.576347] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 1306.576352] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 1306.576355] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 1306.576359] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 1306.576362] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 1306.576366] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 1306.576370] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 1306.576373] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 1307.277503] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 1622.583086] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 1622.585585] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code [ 1622.585603] cfg80211: World regulatory domain updated: [ 1622.585611] cfg80211: DFS Master region: unset [ 1622.585611] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 1622.585618] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 1622.585623] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 1622.585626] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 1622.585630] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 1622.585634] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 1622.585637] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 1622.585641] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 1622.585644] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 1623.287611] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 1938.580273] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 1938.587515] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code [ 1938.587571] cfg80211: World regulatory domain updated: [ 1938.587604] cfg80211: DFS Master region: unset [ 1938.587604] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 1938.587617] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 1938.587633] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 1938.587654] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 1938.587666] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 1938.587676] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 1938.587687] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 1938.587694] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 1938.587705] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 1939.294771] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2083.905735] fuse init (API version 7.23) [ 2254.629486] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2254.631800] brcmfmac: brcmf_cfg80211_reg_notifier: not a ISO3166 code [ 2254.631815] cfg80211: World regulatory domain updated: [ 2254.631823] cfg80211: DFS Master region: unset [ 2254.631823] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 2254.631828] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 2254.631833] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 2254.631836] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 2254.631840] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 2254.631844] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 2254.631847] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 2254.631850] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 2254.631853] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 2255.303333] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
================================================================
ever going.
What is going on here, and what can be done? Of course I did some googling, but I didn't find anything alike...
I think the best would be to open a bug in bugzilla for this. Maybe you want to attache the wpa_supplicant log as well. Not sure about this, I'm rather a wifi noop.
I'll await the dialogue with Stefan before issuing a bugreport.
Thanks, Matthias
I'm not sure where to put -- To unsubscribe, e-mail: opensuse-arm+unsubscribe@opensuse.org To contact the owner, e-mail: opensuse-arm+owner@opensuse.org