Hi,
I just installed 9.2 on my home server and am experiencing some trouble. On
boot the ethernet card is not being correctly initialized and therefore all
subsequent startups like DHCP, DNS etc. all have problems.
As you can see by the output below, it seems the interface is not
getting/retaining its (ipv4) address.
If I restart the network service everything is fine and all other services
function normally.
Some of the relevant output follows. It's SuSE 9.2 on a 1.5 Mhz Pentium 4.
TIA,
Frank
Here's ifstatus eth0 when it's not working:
mother:~ # ifstatus eth0
ifstatus [DEBUG] eth0
ifstatus [DEBUG] HWDESC = eth0 CONFIG = eth0 INTERFACE = eth0
ifstatus eth0 device: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev
08)
ifstatus eth0 is up
ifstatus 2: eth0: mtu 1500 qdisc pfifo_fast qlen 1000
link/ether 00:02:b3:8b:4a:23 brd ff:ff:ff:ff:ff:ff
inet6 fe80::202:b3ff:fe8b:4a23/64 scope link
valid_lft forever preferred_lft forever
ifstatus-route [DEBUG] eth0 eth0
ifstatus-route Configured routes for interface eth0:
ifstatus-route 169.254.0.0 - 255.255.0.0 eth0
ifstatus-route
ifstatus-route 0 of 1 configured routes for interface eth0 up
ifstatus-wireless [DEBUG] eth0 eth0
ifstatus-wireless [DEBUG] eth0 is not wireless, exiting
ifstatus-wireless-wpa [DEBUG] eth0 eth0
ifstatus-wireless-wpa [DEBUG] eth0 is not wireless, exiting
ifstatus-connection [DEBUG] eth0 eth0
mother:~ # ifconfig
eth0 Link encap:Ethernet HWaddr 00:02:B3:8B:4A:23
inet6 addr: fe80::202:b3ff:fe8b:4a23/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:460 (460.0 b)
lo Link encap:Local Loopback
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
modem0 Link encap:Point-to-Point Protocol
inet addr:66.84.234.55 P-t-P:66.84.234.2 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:3 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:3 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:42 (42.0 b) TX bytes:183 (183.0 b)
mother:~ #
And here it is when it is working:
mother:~ # /etc/init.d/network start
network [DEBUG] start
network [DEBUG] CONFIG =
network [DEBUG] INTERFACE =
network [DEBUG] AVAILABLE_IFACES = eth0
network [DEBUG] PHYSICAL_IFACES = eth0
network [DEBUG] DIALUP_IFACES = modem0
network [DEBUG] TUNNEL_IFACES =
network [DEBUG] MANDATORY_DEVICES =
network [DEBUG] SKIP =
Setting up network interfaces:
ifup [DEBUG] lo -o rc
ifup [DEBUG] HWDESC = lo CONFIG = lo INTERFACE = lo
ifup lo
ifup-wireless [DEBUG] lo lo -o rc
ifup-wireless [DEBUG] unknown option rc ignored
ifup-wireless [DEBUG] lo is not wireless, exiting
ifup-wireless-wpa [DEBUG] lo lo -o rc
ifup-wireless-wpa [DEBUG] unknown option rc ignored
ifup-wireless-wpa [DEBUG] lo is not wireless, exiting
ifup lo ifup IP address: 127.0.0.1/8 ifup
ifup [DEBUG] Handling Index <>:
IPADDR = 127.0.0.1
PREFIXLEN = 8
CHECK_DUPLICATE_IP = no
ifup-route [DEBUG] lo lo -o rc
ifup-route [DEBUG] calling: ip route replace to 127/8 dev lo ---> OK
ifup-services [DEBUG] lo lo -o rc
ifup-services [DEBUG] unknown option rc
ifup-services [DEBUG] No services to handle
ifup [DEBUG] executing additional global start script
if-up.d/dhcpcd-hook-samba
lo returned 0 done
ifup [DEBUG] eth0 -o rc
ifup [DEBUG] HWDESC = eth0 CONFIG = eth0 INTERFACE = eth0
ifup eth0 device: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
ifup-wireless [DEBUG] eth0 eth0 -o rc
ifup-wireless [DEBUG] unknown option rc ignored
ifup-wireless [DEBUG] eth0 is not wireless, exiting
ifup-wireless-wpa [DEBUG] eth0 eth0 -o rc
ifup-wireless-wpa [DEBUG] unknown option rc ignored
ifup-wireless-wpa [DEBUG] eth0 is not wireless, exiting
ifup eth0 ifup IP address: 192.168.0.10/24 ifup
ifup [DEBUG] Handling Index <>:
IPADDR = 192.168.0.10
PREFIXLEN = 24
CHECK_DUPLICATE_IP = no
ifup-route [DEBUG] eth0 eth0 -o rc
ifup-route [DEBUG] calling: ip route replace to 169.254.0.0/16 dev eth0 --->
OK
Nothing to flush.
ifup-services [DEBUG] eth0 eth0 -o rc
ifup-services [DEBUG] unknown option rc
ifup-services [DEBUG] No services to handle
ifup [DEBUG] executing additional global start script
if-up.d/dhcpcd-hook-samba
eth0 returned 0 done
network [DEBUG] ... still waiting for hotplug devices:
network [DEBUG] SUCCESS_IFACES= lo eth0
network [DEBUG] MANDATORY_DEVICES=
network [DEBUG] ... final
network [DEBUG] SUCCESS_IFACES= lo eth0
network [DEBUG] MANDATORY_DEVICES=
network [DEBUG] TOCHECK_IFACES=
network [DEBUG] FAILED=0
ifup [DEBUG] modem0 -o rc
ifup [DEBUG] HWDESC = modem0 CONFIG = modem0 INTERFACE = modem0
ifup modem0
ifup modem0 Startmode is 'manual'
modem0 returned 5 skipped
ifup-route [DEBUG] noiface -o rc
Setting up service network . . . . . . . . . . . . . . done
mother:~ # ifconfig
eth0 Link encap:Ethernet HWaddr 00:02:B3:8B:4A:23
inet addr:192.168.0.10 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:546 (546.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.BOOTPROTO='static'
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Here's the config:
BROADCAST='192.168.0.255'
IPADDR='192.168.0.10'
MTU=''
NETMASK='255.255.255.0'
NETWORK='192.168.0.0'
REMOTE_IPADDR=''
STARTMODE='onboot'
UNIQUE='1HdK.XvTWJ6g289A'
USERCONTROL='no'
_nm_name='bus-pci-0000:02:0b.0'0.0.0
