Hi guys, I bought a generic flash card reader a while back so I could access my photos using Suse. It worked fine in 8.0 but will not work in 8.2 This is the output I got in Suse 8.0 when plugging in the reader. Aug 27 17:19:39 linux kernel: hub.c: USB new device connect on bus2/2, assigned device number 2 Aug 27 17:19:40 linux kernel: usb.c: USB device 2 (vend/prod 0x58f/0x9321) is not claimed by any active driver. Aug 27 17:19:40 linux kernel: Initializing USB Mass Storage driver... Aug 27 17:19:40 linux kernel: usb.c: registered new driver usb-storage Aug 27 17:19:40 linux kernel: usb-uhci.c: interrupt, status 2, frame# 612 Aug 27 17:19:41 linux kernel: usb_control/bulk_msg: timeout Aug 27 17:19:41 linux kernel: scsi1 : SCSI emulation for USB Mass Storage devices Aug 27 17:19:46 linux kernel: usb_control/bulk_msg: timeout Aug 27 17:20:04 linux kernel: usb-uhci.c: interrupt, status 3, frame# 106 Aug 27 17:20:04 linux kernel: Vendor: Generic Model: USB CF Reader Rev: 2.00 Aug 27 17:20:04 linux kernel: Type: Direct-Access ANSI SCSI revision: 02 Aug 27 17:20:04 linux kernel: Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0 Aug 27 17:20:04 linux kernel: SCSI device sda: 93952 512-byte hdwr sectors (48 MB) Aug 27 17:20:04 linux kernel: sda: Write Protect is off Aug 27 17:20:04 linux kernel: sda: sda1 Aug 27 17:20:04 linux kernel: WARNING: USB Mass Storage data integrity not assured Aug 27 17:20:04 linux kernel: USB Mass Storage device found at 2 Aug 27 17:20:04 linux kernel: USB Mass Storage support registered. Aug 27 17:20:04 linux insmod: Using /lib/modules/2.4.18-4GB/kernel/drivers/usb/storage/usb-storage.o As you can see it worked but not immediately after plugging it in. Even though it gave a warning it still worked fine and I could read and write to it with no problems at all. However now using 8.2 I get the following. Aug 27 20:40:35 linux kernel: hub.c: new USB device 00:07.3-2, assigned address 2 Aug 27 20:40:35 linux kernel: usb.c: USB device 2 (vend/prod 0x58f/0x9321) is not claimed by any active driver. Aug 27 20:40:38 linux kernel: Initializing USB Mass Storage driver... Aug 27 20:40:38 linux kernel: usb.c: registered new driver usb-storage Aug 27 20:40:38 linux kernel: usb-uhci.c: interrupt, status 2, frame# 859 Aug 27 20:40:39 linux kernel: usb_control/bulk_msg: timeout Aug 27 20:40:39 linux kernel: scsi1 : SCSI emulation for USB Mass Storage devices Aug 27 20:40:39 linux kernel: Vendor: Generic Model: USB CF Reader Rev: 2.00 Aug 27 20:40:39 linux kernel: Type: Direct-Access ANSI SCSI revision: 02 Aug 27 20:40:39 linux kernel: Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0 Aug 27 20:40:39 linux kernel: SCSI device sda: 93952 512-byte hdwr sectors (48 MB) Aug 27 20:40:44 linux kernel: usb_control/bulk_msg: timeout Aug 27 20:41:44 linux kernel: usb-uhci.c: interrupt, status 2, frame# 1438 Thats it. It just seems to hang here and I cant use the reader. Does anyone have any idea how I can get the bugger to work like it did under 8.0? Thanks, Glenn