Hi.
I run SuSE 72. here, and have got diald to call my ISP. I use the ip-up
and ip-down's
that follows 7.2. BUT I cannot get them to run the built in sendmail and
fetchmails calls that ha sto be found in the 2 mentioned scripts.
I have the idea, that the ip-up has been called twice. This is the
reason, that I send
a LONG /var/log/message with this mail -SORRY !!.
The diald is also being called over and over again.
Hope anybody can see what and where the lack is here.
Thank you in advance.
Jul 2 14:05:01 duron diald[1040]: FIFO: link up request
Jul 2 14:05:01 duron diald[1040]: new state CONNECT action 0x8052070
timeout 600
Jul 2 14:05:01 duron diald[1040]: Calling site 192.168.0.2
Jul 2 14:05:02 duron diald[1040]: running '/etc/ppp/chatscript.diald'
Jul 2 14:05:02 duron chat[1048]: report (CONNECT)
Jul 2 14:05:02 duron chat[1048]: report (OK)
Jul 2 14:05:02 duron chat[1048]: report (BUSY)
Jul 2 14:05:02 duron chat[1048]: report (NO CARRIER)
Jul 2 14:05:02 duron chat[1048]: report (NO DIALTONE)
Jul 2 14:05:02 duron chat[1048]: timeout set to 10 seconds
Jul 2 14:05:02 duron chat[1048]: send (ATZ^M)
Jul 2 14:05:02 duron chat[1048]: expect (OK)
Jul 2 14:05:02 duron chat[1048]: CARRIER^M
Jul 2 14:05:02 duron chat[1048]: ATZ^M^M
Jul 2 14:05:02 duron chat[1048]: OK
Jul 2 14:05:02 duron chat[1048]: -- got it
Jul 2 14:05:02 duron chat[1048]: send (ATDT16110^M)
Jul 2 14:05:02 duron diald[1040]: SIGCHLD[5]: pid 1048 dial, status 0
Jul 2 14:05:02 duron diald[1040]: new state START_LINK action 0x8052410
timeout 60
Jul 2 14:05:02 duron diald[1040]: Connected to site 192.168.0.2
Jul 2 14:05:02 duron diald[1040]: Running pppd (pid = 1049).
Jul 2 14:05:02 duron diald[1049]: Running pppd: /usr/sbin/pppd
-defaultroute -detach modem crtscts mtu 1500 mru 1500 netmask
255.255.255.0 noauth user 120010795264 ipcp-accept-local
ipcp-accept-remote
Jul 2 14:05:02 duron pppd[1049]: pppd 2.4.0 started by root, uid 0
Jul 2 14:05:02 duron pppd[1049]: Perms of /dev/ttyS0 are ok, no 'mesg
n' neccesary.
Jul 2 14:05:03 duron pppd[1049]: using channel 2
Jul 2 14:05:03 duron pppd[1049]: Using interface ppp0
Jul 2 14:05:03 duron pppd[1049]: Connect: ppp0 <--> /dev/ttyS0
Jul 2 14:05:03 duron pppd[1049]: sent [LCP ConfReq id=0x1 ]
Jul 2 14:05:05 duron pppd[1049]: sent [LCP ConfReq id=0x1 ]
Jul 2 14:05:05 duron pppd[1049]: rcvd [LCP ConfReq id=0xa4 <auth chap MD5> ]
Jul 2 14:05:05 duron pppd[1049]: sent [LCP ConfRej id=0xa4 ]
Jul 2 14:05:05 duron pppd[1049]: rcvd [LCP ConfAck id=0x1 ]
Jul 2 14:05:05 duron pppd[1049]: rcvd [LCP ConfReq id=0xa5 <auth chap MD5> ]
Jul 2 14:05:05 duron pppd[1049]: sent [LCP ConfNak id=0xa5 <auth pap>]
Jul 2 14:05:05 duron pppd[1049]: rcvd [LCP ConfReq id=0xa6 <auth pap> ]
Jul 2 14:05:05 duron pppd[1049]: sent [LCP ConfAck id=0xa6 <auth pap> ]
Jul 2 14:05:05 duron pppd[1049]: sent [LCP EchoReq id=0x0
magic=0x5820274f]
Jul 2 14:05:05 duron pppd[1049]: cbcp_lowerup
Jul 2 14:05:05 duron pppd[1049]: want: 2
Jul 2 14:05:05 duron pppd[1049]: sent [PAP AuthReq id=0x1
user="120010795264" password=<hidden>]
Jul 2 14:05:05 duron pppd[1049]: rcvd [LCP EchoRep id=0x0
magic=0x1f034bd5]
Jul 2 14:05:08 duron pppd[1049]: sent [PAP AuthReq id=0x2
user="120010795264" password=<hidden>]
Jul 2 14:05:09 duron pppd[1049]: rcvd [PAP AuthAck id=0x2 ""]
Jul 2 14:05:09 duron pppd[1049]: sent [IPCP ConfReq id=0x1 ]
Jul 2 14:05:09 duron pppd[1049]: rcvd [IPCP ConfReq id=0x1 ]
Jul 2 14:05:09 duron pppd[1049]: sent [IPCP ConfAck id=0x1 ]
Jul 2 14:05:09 duron pppd[1049]: rcvd [CCP ConfReq id=0x1 ]
Jul 2 14:05:09 duron pppd[1049]: Unsupported protocol 'Compression
Control Protocol' (0x80fd) received
Jul 2 14:05:09 duron pppd[1049]: sent [LCP ProtRej id=0x2 80 fd 01 01
00 0a 12 06 00 00 00 01]
Jul 2 14:05:09 duron pppd[1049]: rcvd [IPCP ConfNak id=0x1 ]
Jul 2 14:05:09 duron pppd[1049]: sent [IPCP ConfReq id=0x2 ]
Jul 2 14:05:09 duron pppd[1049]: rcvd [IPCP ConfAck id=0x2 ]
Jul 2 14:05:09 duron pppd[1049]: local IP address 195.249.30.137
Jul 2 14:05:09 duron pppd[1049]: remote IP address 195.249.0.237
Jul 2 14:05:10 duron diald[1040]: New addresses: local 195.249.30.137,
remote 195.249.0.237, broadcast 0.0.0.0
Jul 2 14:05:10 duron diald[1040]: running '/sbin/ifconfig ppp0
195.249.30.137 pointopoint 195.249.0.237 broadcast 0.0.0.0 netmask
255.255.255.0 metric 0 mtu 1500 up'
Jul 2 14:05:10 duron diald[1040]: start ppp0: SIOCSIFMETRIC: Operation
not supported
Jul 2 14:05:10 duron diald[1040]: SIGCHLD[6]: pid 1051 system, status
256
Jul 2 14:05:10 duron diald[1040]: start ppp0: Establishing routes for
ppp0
Jul 2 14:05:10 duron diald[1040]: running '/usr/sbin/ip route replace
195.249.0.237 dev ppp0 scope link src 195.249.30.137 metric 0 '
Jul 2 14:05:10 duron diald[1040]: SIGCHLD[7]: pid 1052 system, status 0
Jul 2 14:05:10 duron diald[1040]: running '/usr/sbin/ip route replace
default dev ppp0 scope link src 195.249.30.137 metric 0 '
Jul 2 14:05:10 duron diald[1040]: SIGCHLD[8]: pid 1053 system, status 0
Jul 2 14:05:10 duron diald[1040]: stop tap0: Removing routes for tap0
Jul 2 14:05:10 duron diald[1040]: running '/usr/sbin/ip route del
default dev tap0 scope link src 192.168.0.1 metric 1'
Jul 2 14:05:10 duron diald[1040]: SIGCHLD[9]: pid 1054 system, status 0
Jul 2 14:05:10 duron diald[1040]: running '/sbin/ifconfig tap0 0.0.0.0'
Jul 2 14:05:10 duron diald[1040]: SIGCHLD[10]: pid 1055 system, status
0
Jul 2 14:05:10 duron diald[1040]: new state UP action 0x80525a0 timeout
120
Jul 2 14:05:10 duron diald[1040]: Changed snoop device to ppp0
Jul 2 14:05:10 duron diald[1040]: running ip-up script
'/etc/diald/ip-up 'ppp0' '255.255.255.0' '195.249.30.137'
'195.249.0.237''
Jul 2 14:05:10 duron diald[1040]: running '/etc/diald/ip-up 'ppp0'
'255.255.255.0' '195.249.30.137' '195.249.0.237''
Jul 2 14:05:10 duron diald[1040]: SIGCHLD[11]: pid 1056 system, status
256
Jul 2 14:05:10 duron diald[1040]: ip-up: Usage: /etc/diald/ip-up
<INTERFACE> <DEVICE> <SPEED> <LOCALIP> <REMOTEIP>
--
Med venlig hilsen // Best regards // VY 73 de Erik OZ4KK
Erik Jakobsen // erik@urbakken.dk
Powered by SuSE Linux 6.3
*********************************************************
