From what I've read on todays posts, SuSE likes doing things without telling you (see the Sendmail
I'm no CD buring expert - but you seem to have a problem with your IDE set up. The traxdata you mentioned is an IDE device is it not? And it seems to me that something is making Linux detect a change somehow from the Secondary Master (HDC) to Secondary Slave. Do you have Cable select on the CD internally? Change it to either Master OR Slave, depending how you set it up. Other than that - I haven't got a clue! :o) posts from Rogier!!). I'd check your fstab files and check to see what your CDRW is set to (do a dmesg). Is it HDC or HDD? Kevin Jackson -- http://www.thelinuxwebsite.com/ -- Coming Soon (Monday 17th April) -----Original Message----- From: michael.norman1 [mailto:michael.norman1@which.net] Sent: 13 April 2000 00:17 To: suse-linux-e@suse.com Subject: [SLE] CD Burning errors Hi all. I have a Traxdata CDRW2260 cd burner which until recently has burned audio cds quite happily using XCDroast. However it has now started to fail. Using XDRoast I got two cds which failed about two thirds of the way through. No material on them was readable on any CD drive. I looked in var/log/messages and found the following : Apr 9 14:04:59 Normans kernel: VFS: Disk change detected on device sr(11,0) Apr 9 14:06:07 Normans kernel: ide-scsi: hdc: unsupported command in request queue (0) Apr 9 14:06:07 Normans kernel: end_request: I/O error, dev 16:00 (hdc), sector 0 Apr 9 14:06:07 Normans kernel: ide-scsi: hdd: unsupported command in request queue (0) Apr 9 14:06:07 Normans kernel: end_request: I/O error, dev 16:40 (hdd), sector 0 Apr 9 14:35:08 Normans -- MARK -- Apr 9 14:55:08 Normans -- MARK -- I then decide to use cdrecord from the console, a dummy write was successful and I was also able to write a few tracks to a cdrw as a test. But when I went for a real burn it again died half way through and left me with another coaster. The relevant error message is : Executing 'test unit ready command on Bus 0 Target 1, Lun 0 timeout 240s CDB: 51 00 00 00 00 00 00 00 10 00 cdrecord: Input/output error, read disk info: scsi sendcmd: retryable error CDB: 51 00 00 00 00 00 00 00 10 00 staus: 0x2 (CHECK CONDITION) Sense bytes: FO 00 02 00 00 00 00 19 00 00 6A 6E 3A 00 00 00 Sense Key: 0x2 Not Ready, Segment 0 Sense Code 0x3A Qual 0x00 (medium not present) Fru 0x0 Sense flags: Blk 0 (valid) cmd finished after 0.0002s timeout 240s The same drive works in W98 using WinonCD I ahve burnt a couple of CD's successfully since the problems in Linux starteds o I don't think its a hardware problem Can anyone offer any clues as to what might be going wrong and how I might fix it ? TIA Mike -- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/Support/Doku/FAQ/ -- To unsubscribe send e-mail to suse-linux-e-unsubscribe@suse.com For additional commands send e-mail to suse-linux-e-help@suse.com Also check the FAQ at http://www.suse.com/Support/Doku/FAQ/